Classic Exhibits VK-1122 Setup Instructions

Classic Exhibits
Brand
Classic Exhibits
Model
VK-1122
Type
Setup Instructions

Classic Exhibits VK-1122 is a versatile and customizable display system that can be used for a variety of purposes, including trade shows, exhibitions, and retail displays. The system is made of lightweight aluminum extrusion and features a patented expandable lock that creates a strong and positive connection between components.

The VK-1122 can be assembled in a variety of configurations, including straight walls, curves, and counters. The system also includes a variety of accessories, such as lights, shelves, and monitor mounts, that can be used to customize the display to meet your specific needs.

Classic Exhibits VK-1122 is a versatile and customizable display system that can be used for a variety of purposes, including trade shows, exhibitions, and retail displays. The system is made of lightweight aluminum extrusion and features a patented expandable lock that creates a strong and positive connection between components.

The VK-1122 can be assembled in a variety of configurations, including straight walls, curves, and counters. The system also includes a variety of accessories, such as lights, shelves, and monitor mounts, that can be used to customize the display to meet your specific needs.

www.classicexhibits.com
Step 1
Page 1 of 4
866.652.2100
© 2014
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - General Layout
Plan View
Perspective View
10’
10’
www.classicexhibits.com
Step 2
Page 2 of 4
866.652.2100
© 2014
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - General Information
The Tool Typical Connection
Horizontal Inline Connection (remove only one setscrew)
Base Plate Connection Vertical Connection
(remove only two setscrews)
Most Visionary Designs exhibits can be
assembled with the supplied Hex Key Tool.
Occasionally, a flat head screwdriver may
be required.
Most horizontal extrusion connections have a patented expandable lock. This lock inserts into
the groove of an opposing extrusion. Tightening the lock with the Hex Key Tool expands the lock
and creates a strong positive connection.
Remove only (1) setscrew when disassembling. Replace setscrew in
extrusion after assembling it. Before packing, replace setscrew in
extrusion to avoid losing it.
Attach base plate to round or square
vertical extrusion using the bolt provided.
Be careful not to strip the threads.
When vertical extrusions are packed in
portable cases rather than crates or
tubs, they must broken down into
smaller sections which then require
assembly.
Remove only (2) setscrews when
disassembling. Replace setscrews in
extrusion after assembling it. Before
packing, replace setscrews in extrusion
to avoid losing them.
Using Your Setup Instructions
The Visionary Designs Setup Instructions are created specifically for your
configuration. They are laid out sequentially, including an exploded view of
the entire display, and then a logical series of detailed steps to assemble the
main structure and components. We encourage you to study the instructions
before attempting to assemble your exhibit.
Each page reminds you to tighten the setscrews after disassembling your
exhibit to prevent loss of the locks and setscrews (see below in RED).
This is VERY IMPORTANT.
Cleaning and Packing Your Display
1) Use care when cleaning aluminum extrusion or acrylic inserts. Use only
non-abrasive cleaners.
2) When cleaning laminate inserts or countertops, use mild cleansers and a
soft material such as cotton.
3) Keep all display components away from extreme heat and long exposure
to sunlight to avoid warping and fading.
4) Retain all packing material. It will make re-packing much easier and will
reduce the likelihood of shipping damage.
Typical Connection (cont’d)
Numbered Label
Each extrusion contains a numbered label which
corresponds with setup instructions.
The label is located within a groove of the extrusion
(when possible). With Visionary Designs the labels
contain Black numbers unless otherwise specified.
Detail C E liateDD liateDDetail B
Detail A
Setscrews
www.classicexhibits.com
Step 1
Page 1 of 4
866.652.2100
© 2014
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - VK-1122 Backwall Assembly
1A
1A
1
6
5
3
4
8
7
2
When assembled
Item
1A
1
2
3
4
5
6
7
8
Qty.
2
1
1
1
1
1
1
1
1
Description
Base Plates
39” Vertical extrusion
39” Vertical extrusion top left outside cut
39” Vertical extrusion
39” Vertical extrusion top right outside cut
41” Horizontal extrusion
41” Horizontal extrusion
41” Top left curved extrusion
41” Top right curved extrusion Front View
Back View
Steps:
1) Attach base plates [1A] to lower verticals [1,3].
2) Connect upper verticals [2,4] with
connection bars [b].
3) Connect horizontals [5,6] with connection bar [a].
4) Connect vertical [1/2,3/4] with horizontal
assembly [5/6].
5) Connect curved extrusions [7,8] with
connection bar [a].
6) Connect curved assembly [7/8] between
verticals [1/2,3/4].
7) Attach Graphic to velcro on back of frame as shown.
Velcro:
Back/Top
Edge
Velcro:
Back/Bottom
Edge
Velcro:
Inside
Edge
Velcro:
Inside
Edge
Attach graphic
to velcro on back of
assembled frame
Horizontal Placement
Stopper
Set upper horizontal
bar atop stopper where
indicated on verticals
Turn Knob Clockwise
to Tighten Lock
indicates location of
knobs on BACKSIDE of unit.
Do not over tighten Knobs
Knob
Knob
indicates
location of connection
lock with knob.
Note: Slide connection
bar between extrusions and
tighten knobs to secure.
Connection Bar
a
b
a
b
www.classicexhibits.com
Step 2
Page 2 of 4
866.652.2100
© 2014
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - VK-1122 Backwall Attachments
When assembled
Steps:
1) Attach A10 Clips and wing graphics
as shown in Wing Attachment detail.
2) Connect stand off barrels to backwall
then attach circle graphic as shown in
Graphic Attachment detail.
3) Attach Light atop display as shown in
Light Connection detail.
Light Connection
Attach light to
backwall where
desired and tighten
in place.
Graphic
Cap
Standoff
Barrel
Slide connector on back of standoff
barrels into groove of extrusion
and twist to secure in place. Secure graphic
to standoffs using screw caps.
Graphic Attachment
Slide A10 Clamp
into groove
of square extrusion.
When desired location
is found, tighten
set screw to secure.
Set-
Screw
A10
Tighten black plastic
set screw to secure
Wing in place.
Plastic
Knob
Wing Attachment
www.classicexhibits.com
Step 3
Page 3 of 4
866.652.2100
© 2014
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - VK-1122 Backwall Counter and Monitor Mount Attachments
9
10
11
9
10
11
When assembled
Item
9
10
11
Qty.
2
2
2
Description
11.5” Horizontal Extrusion
26.75” Curved Extrusion
20.3” Curved Extrusion
Steps:
1) Attach Curved extrusions [10,11].
2) Attach horizontal extrusion [9] to [10/11].
3) Connect [9/10/11] to vertical extrusion as shown.
4) Screw in top plate to curved extrusion [10] as shown.
5) Connect counter top as shown in detail below.
6) Attach monitor mounts as shown in detail.
Monitor Mount Attachment
Connectors
Attach monitor mount back
plate to connectors using
setscrews provided.
*
*
*
Screw
Screw
Note: Curved extrusion
[10] and horizontal [11]
stay assembled for
shipping and packing.
Counter Top Attachment
Insert screws located
on underside of counter
into holes on flange plate
and secure with wing nuts.
Wing Nut
www.classicexhibits.com
Step 4
Page 4 of 4
866.652.2100
© 2014
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - Pedestal
Counter
Infill
Hinge
Infill
Infill
6
3
2
4
10
9
12
11
5
1
8
7Back Side
When assembled
Front Side
When assembled
Item
1-2
3-4
5
6-7
8
9
10-11
12
Qty.
1ea.
1ea.
1
1ea.
1
1
1ea.
1
Description
38” Vertical Extrusion w/ cut
38” Vertical Extrusion
18.9” Horizontal Extrusion
18” Horizontal Extrusion
20” Horizontal Extrusion
22.5” Curved Extrusion
18” Horizontal Extrusion
20” Horizontal Extrusion
Door
Hinge
Hinge
Door Attachment
Slide pin into
hinge attached
to vertical.
Slide door
hinge atop pin.
Hinge
Door
Steps:
1) Attach lower horizontals [5,6,7,8] between
verticals [1,2,3,4] as shown.
2) Attach door using pins as shown in
Door Attachment detail.
3) Insert infills as shown.
4) Attach upper horizontals [9,10,11,12] between verticals.
5) Place counter on top.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6

Classic Exhibits VK-1122 Setup Instructions

Classic Exhibits
Brand
Classic Exhibits
Model
VK-1122
Type
Setup Instructions

Classic Exhibits VK-1122 is a versatile and customizable display system that can be used for a variety of purposes, including trade shows, exhibitions, and retail displays. The system is made of lightweight aluminum extrusion and features a patented expandable lock that creates a strong and positive connection between components.

The VK-1122 can be assembled in a variety of configurations, including straight walls, curves, and counters. The system also includes a variety of accessories, such as lights, shelves, and monitor mounts, that can be used to customize the display to meet your specific needs.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages

Related papers