Quick Start
186-86000-02 B00
STEP 1 EXB RT Battery Module Unpacking and Parts Check
EXB Quick Start
EXB RT Quick Start
Warranty and
Product Registration
Battery Power Cable
EXB RT Battery Module Box Contents
- EXB 5RT Battery Module Part number 86207
- EXB 7RT Battery Module Part number 86207
- EXB 11RT Battery Module Part number 86209
Bezel Hex Drive
Detection Cable
Tower Stand Expanders
(not to scale) Stabilizer Bracket
(4 screws included)
41
Rail Kit
www.mgeops.com
EX 5/7/11RT Systems
Quick Start
STEP 2 EXB RT Tower Configuration
Tower Configuration with Optional Multiple EXB Modules (2 EXBs shown)
Power Module
EXB Battery
Module(s)
(up to 6)
E X 11 R T
Tower Configuration of Standard System
Battery
Module
(up to 6)
E X B R T
E X 1 1 R T
OFFON
Power Module
Battery Modules
Power Module
Battery Module
Use tower stand expanders provided with each battery module to enlarge the footings.
Power Module
1
1
2
2
4
4
4
4
33
5
1
1
2
2
4
4
4
4
33
5
Battery Module EXB 5/7/11 RT
286-86000-02 B00EXB Quick Start
Quick Start
EXB Quick Start 386-86000-02 B00
STEP 3 Rack Configuration
See System Installation and User Manual for details.
EXB RT Front Panel Display and Rack Installation
E X 1 1 R T
OFFON
E X 1 1 R T
OFFON
E X 1 1 R T
OFFON
E X 1 1 R T
OFFON
1
2
3
FINISHED PANEL
(rack orientation)
1
2
3
A. Prepare the front panel logo and LCD display for
rack orientation, Apply to all modules including
Transformer, CLA, if equipped (Power Moduler shown).
EXB RT
EX RT Transformer
Layout of Modules in Rack Configuration
(3 EXBs shown)
EX RT Transformer
OFFON
EX 11 RT
B. Rack Installation
3
4
4
4
42
2
1
4
4
5
1
66
6
1. Attach both front mounting ear brackets
to module with supplied screws. (For this
step, it is possible to adjust the position
of both front mounting brackets.)
2. Attach rear support brackets to module.
These brackets prevent the module from
sliding out of the rack.
3. Attach rails together, secure with
wing nuts, and finger tighten (both sides).
4. Attach both rails to rear and front of rack
with supplied flathead screws (as
shown).
5. Use caution when sliding unit into rack.
Temporarily secure unit to rack with
thumb screws on front mounting
brackets.
6. Secure rear support brackets to rails.
6
1. Power Module
(Top, EX 5/7/11 RT)
2. EXB RT Battery
Module (Upper)
3. EXB RT Battery
Module (lower)
4. EXB RT Battery
Module (bottom)
Battery Module EXB 5/7/11 RT
486-86000-02 B00
STEP 4 System Connections
EXB Quick Start
1. Check that the battery circuit breaker is in the OFF (“0”) position.
2. & 3. Connect the battery power cable and battery detection cable as shown.
A. System Connections with Battery Modules
Battery Module Circuit Breaker
Battery Power Cable
Battery Detection Cable
1
2
3
1
2
See EX 5/7/11 RT System Installation and User Manual for initial start-up procedures.
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
in other languages
Related papers
-
MGE UPS Systems EX-5, EX-7, EX-11RT User manual
-
-
-
-
MGE UPS Systems 66229 Datasheet
-
-
-
-
-
Other documents
-
Eaton EX RT 11 Quick start guide
-
-
-
-
Eaton 68502 Datasheet
-
-
-
-
Eaton EX 1500 RT2U User manual
-