KT&C KPC DN100 Operating instructions

Thank you for choosing our high quality camera.

Before attempting to connect or operate, please read and follow

these instructions.

OPERATION MANUAL

M060-DN100-001

z

CONTENTS

1. Cautions

2. Features

3. Package

4. Overview and function

5. Installation

6. Connection

7. Dimensions

8. Specifications

9. Setup menu operation

• SETUP MENU

• SETUP MODE

• CAMERA ID

• LENS

• SHUTTER

• WHITE BALANCE

• LANGUAGE MODE SETUP

• RESET

10.Funtion Menu operation

• FUNTION MENU

• BLC

• AGC

• DAY&NIGHT

• PRIVACY

• MIRROR

• GAMMA

• MOTION

11.Troubleshooting

3

1.Cautions

4

This device complies with Part 15 of the FCC

Rules. Operation is subject to the following two

conditions;

1. This device may not cause harmful interference.

2. This device must accept any interference received, including

interference that may cause undesired operation.

This equipment has been tested and found to comply with limits for a Class B digital

device, pursuant to part 15 of the FCC Rules. These limits are designed to provide

reasnoable protection against harmful interference in a residential installation.

This equipment generates, uses, and can radiate radio communications.

However, there is no guarantree that interference will not occur in a particular

installation. If this equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

Note-

• Reorient or relocate the receiving antena.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to 　

whice the receiver is connected.

• Consult the dealer or an experienced radio / tv technician for helf.

Any changes or modications in construction of this devies

which are not expressly approved by the party responsible

for compliance could void the user's authority to operate the

equipment.

Caution -

1. A regulated DC12V 1.5A power supply is recommended for use with this camera

for the best picture and the most stable operation.

An unregulated power supply can cause damage to the camera.

When unregulated power supply is applied, product warranty will be

out of subject.

2. It is recommended that the camera is used with a monitor that has a CCTV quality

75 video impedance level.

If your monitor is switched to high impedance the n please adjust accordingly.

3. Do not attempt to disassmble the camera to gain access to the internal conponets.

Refer servicing to your dealer.

4. Never face the camera towards the sun or any bright or reective light, which may

cause smear on the picture and possible damage to the CCD.

5. Do not remove the serial sticker for the warranty service.

Correct Disposal of This Product

(Waste Electrical & Electronic Equipment)

(Applicable in the European Union and other European countries with

separate collection systems)

This marking shown on the product or its literature, indicate that it should not

be disposed with other household wastes at the end of its working life. To

prevent possible harm to the environment or human health from uncontrolled

waste disposal, please separate this from other types of wastes and recycle it

responsibly to promote the sustainable reuse of material resources.

This product should not be mixed with other commercial wastes purchased this

product, or their local government ofce, for details of where and how they can

take item for environmentally safe recycling.

Business users should contact their supplier and check the terms and

conditions of the purchase contract.

Household users should contact either the retailer where they for disposal.

1.Cautions

5

CAUTIONS

1

2.Features

6 7

• 1/3″Sony Super HAD CCDⅡ

• 550TV Lines

• OSD Function

• Digital slow shutter, Manual shutter

• Privacy Zone

• Dual Voltage use DC12V/AC24V

• Motion Detection

• 3-Axis Gimbal

The Service Video Connector also provides the installer with an

easy way of configuring the camera.

• Service Video connector

6 7

FEATURES

2

CAUTIONS

1

3.

Package

1 DOME CAMERA

2 VIDEO OUTPUT TEST CABLE

3 OPERATION MANUAL

4 SCREW - 3ea

4.Overview and function

• CONTROL FUNCTION

(OSD JOYSTICK)

LEFT

UP

RIGHT

DOWN

MENU

• Name (LED Type)

• Name (Standard)

8 9

5. Installation

8 9

NO PART NAME

STANDARD Type LED Type

1Housing Botton

2Holder Panning

3Holder Tlit

4Holder Rotate

5Cover Sun Shield Cover LED

6Housing Top

7Cover, Dome

1

2

3

4

5

6

7

Standard Type

LED Type

6.Connection

10

BNC FEMALE

VIDEO

VIDEO IN

DC 12V POWER SUPPLY

BNC FEMALE

VIDEO

VIDEO IN

DC 12V / AC 24V

DUAL POWER SUPPLY

When you install the camera, please glue up the end of cable to

keep it stable in order to protect the camera from the humidity problems.

• DUAL(DC12V/AC24V)

• DC12V

7.Dimensions

11

Ø136.4

45

95.3

Ø100

Unit : mm

50˚ 70˚

65˚

◀ When using a wide angle lens

of 2.6mm, Tilt is not available

over 65°.

8.Specifications

12

Signal Format NTSC PAL

image Device 1/3″Sony Super HAD CCDⅡ

Scanning System 2:1 Interlace

H.Resolution 550TV Lines

Scanning Frequency H:15.734KHz, V:59.94Hz H:15.625KHz, V:50Hz

Total Pixels 811(H) x 508(V) 795(H) x 596(V)

Effective Pixels 768(H) x 494(V) 752(H) x 582(V)

Electronic Shutter Speed 1/60 sec 1/50 sec

S/N Ratio More than 48dB(AGC Off)

Gamma r=0.45

Min. Illumination 0.05 Lux / Face Plate

Sync System Internal

Video Output 1.0 Vp-p Composite 75(Ω) unbalanced

Power

Consumption

DC12V DC 12V (±10%) Max110mA

Dual DC 12V (±10%) 160mA

AC 24V (±10%) 1.8W

Operating Temperature -10℃ ~ +50℃

Storage Temperature -20℃ ~ +60℃

Operating Humidity 10% ~ 80%

Options Dual Power

Weight 343g

Power

Consumption

DC12V DC 12V (±10%) Max 550mA

Dual DC 12V (±10%) 650mA

AC 24V (±10%) 6.8W

Min. Illumination 0 Lux (IR LED ON)

IR LED 30ea

IR LED Half Angle ±22 Degree

IR LED Wavelenght 850nm

IR Beam Range Up to 30M

IR LED Operation On : 1 Lux, Off : 3 Lux

LED TYPE

When you x the focus around 22.0mm in f9.0-22.0mm Varifocal lens, please set short

distance focus approximately 3M and do not set long distance focus

Face Plate : Point at the CCD without obstruction of light from any other material.

9.Setup menu operation

OSD STRUCTURE

• ▲,▼ : Menu up / down

• ◀,▶ : Set-up Key

• ■ : MENU(SELECTION KEY)

SETUP MENU

CAMERA ID • ON • OFF

LENS • MANUAL • VIDEO • DC

SHUTTER • AUTO • FLK • FIXED • MANUAL

WHITE BAL. • ATW • AWB • FIXED • MANUAL

FUNCTION

• BLC • AGC • DAY & NIGHT • PRIVACY

• MIRROR • GAMMA • MOTION

ADJUST • CONTRAST • SHARPNESS

• CB_GAIN • CR_GAIN

LANGUAGE • ENGLISH • KOREAN • CHINESE1 • CHINESE2 • JAPANESE

RESET • YES • NO

EXIT

13

14 15

9.Setup menu operation

14 15

9.Setup menu operation

16 17

9.Setup menu operation

16 17

10.Funtion Menu operation

18 19

10.Funtion Menu operation

18 19

10.Funtion Menu operation

20 21

10.Funtion Menu operation

20 21

Page is loading ...

KT&C KPC DN100 Operating instructions

KT&C KPC DN100 Operating instructions

Related papers

Other documents