Endres+Hauser 71399069/71531419 Operating instructions

Brand: Endres+Hauser

Model: 71399069/71531419

Type: Operating instructions

This manual is also suitable for

71399069

Endres+Hauser 71399069/71531419 is a flow assembly designed for inline monitoring of drinking water quality. It accommodates various sensors, including turbidity, pH, chlorine, and dissolved oxygen sensors. Its compact design allows for easy installation and maintenance, making it suitable for use in pipelines to monitor water quality continuously and ensure compliance with drinking water regulations.

Products Solutions Services

Operating Instructions

71399069

CDP chamber 2 for drinking water monitoring

BA01976C/07/EN/01.19

71446999

2019-08-31

About this document 71399069

2 Endress+Hauser

1 About this document

1.1 Warnings

Structure of information Meaning

LDANGER

Causes (/consequences)

If necessary, Consequences of

non-compliance (if applicable)

‣Corrective action

This symbol alerts you to a dangerous situation.

Failure to avoid the dangerous situation will result in a fatal or serious

injury.

LWARNING

Causes (/consequences)

If necessary, Consequences of

non-compliance (if applicable)

‣Corrective action

This symbol alerts you to a dangerous situation.

Failure to avoid the dangerous situation can result in a fatal or serious

injury.

LCAUTION

Causes (/consequences)

If necessary, Consequences of

non-compliance (if applicable)

‣Corrective action

This symbol alerts you to a dangerous situation.

Failure to avoid this situation can result in minor or more serious injuries.

NOTICE

Cause/situation

If necessary, Consequences of

non-compliance (if applicable)

‣Action/note

This symbol alerts you to situations which may result in damage to

property.

1.2 Symbols

Symbol Meaning

Additional information, tips

Permitted or recommended

Not permitted or not recommended

Reference to device documentation

Reference to page

Reference to graphic

 Result of a step

1.3 Symbols on the device

Symbol Meaning

Reference to device documentation

71399069 Basic safety instructions

Endress+Hauser 3

2 Basic safety instructions

2.1 Requirements for personnel

• Installation, commissioning, operation and maintenance of the measuring system may

be carried out only by specially trained technical personnel.

• The technical personnel must be authorized by the plant operator to carry out the

specified activities.

• The electrical connection may be performed only by an electrical technician.

• The technical personnel must have read and understood these Operating Instructions

and must follow the instructions contained therein.

• Faults at the measuring point may only be rectified by authorized and specially trained

personnel.

Repairs not described in the Operating Instructions provided must be carried out only

directly at the manufacturer's site or by the service organization.

2.2 Designated use

The flow assembly is specially designed to accommodate the CUS52D optical turbidity

sensor. In addition, the assembly has 3 installation slots for other sensors: 2 for sensors

with Pg 13.5 and an installed length of 120 mm ( e.g. pH or ORP sensors) and one for

sensors with M35 x 2 (e.g. chlorine dioxide, free chlorine or total chlorine sensors).

Thanks to its design, it can be used in pressurized systems.

2.2.1 Non-designated use

Use of the device for any purpose other than that described, poses a threat to the safety of

people and of the entire measuring system and is therefore not permitted.

The manufacturer is not liable for damage caused by improper or non-designated use.

2.3 Workplace safety

As the user, you are responsible for complying with the following safety conditions:

• Installation guidelines

• Local standards and regulations

• Regulations for explosion protection

2.4 Operational safety

Before commissioning the entire measuring point:

1. Verify that all connections are correct.

2. Ensure that electrical cables and hose connections are undamaged.

3. Do not operate damaged products, and protect them against unintentional operation.

4. Label damaged products as defective.

During operation:

‣If faults cannot be rectified:

products must be taken out of service and protected against unintentional operation.

Basic safety instructions 71399069

4 Endress+Hauser

2.5 Product safety

The product is designed to meet state-of-the-art safety requirements, has been tested, and

left the factory in a condition in which it is safe to operate. The relevant regulations and

international standards have been observed.

71399069 Product description

Endress+Hauser 5

3 Product description

A0035157

 1 Overview

1 Outlet (compression fitting DN6/8)

2 Drain screw ¼"

3 Securing screw

4 Inlet (compression fitting DN6/8)

5 Housing with holder

6 Rinse connection ¼"

7 Clamp coupling 2''

The assembly can be rotated around the horizontal axis in steps of 90°. To do so,

release the securing screw (item 3) under the housing. After rotating the assembly,

tighten the securing screw again.

A0040206

 2 Cover

1 M35 x 2 coupling

2 PG 13.5 coupling

3 Outlet (compression fitting DN6/8)

Incoming acceptance and product identification 71399069

6 Endress+Hauser

4 Incoming acceptance and product

identification

4.1 Incoming acceptance

1. Verify that the packaging is undamaged.

 Notify the supplier of any damage to the packaging.

Keep the damaged packaging until the issue has been resolved.

2. Verify that the contents are undamaged.

 Notify the supplier of any damage to the delivery contents.

Keep the damaged goods until the issue has been resolved.

3. Check that the delivery is complete and nothing is missing.

 Compare the shipping documents with your order.

4. Pack the product for storage and transportation in such a way that it is protected

against impact and moisture.

 The original packaging offers the best protection.

Make sure to comply with the permitted ambient conditions.

If you have any questions, please contact your supplier or your local Sales Center.

4.2 Product identification

4.2.1 Nameplate

The nameplate provides you with the following information on your device:

• Manufacturer identification

• Serial number

• Ambient and process conditions

• Input and output values

• Safety information and warnings

‣Compare the information on the nameplate with the order.

4.3 Scope of delivery

The delivery comprises:

• Assembly in the version ordered

• Assembly holder

• Operating Instructions

‣If you have any queries:

Please contact your supplier or local sales center.

71399069 Installation

Endress+Hauser 7

5 Installation

5.1 Installation conditions

5.1.1 Dimensions

Assembly

38.5 (1.52)

120 (4.72)

290 (11.42)

29 (1.14)

80 (3.15)

48 (1.89)

120 (4.72)

29 (1.14)

A0040213

 3 Assembly. Engineering unit in mm (in)

Installation 71399069

8 Endress+Hauser

Assembly holder

30 (1.18)

! 9 (0.35)

85 (3.35)146 (5.75)

122.5 (4.82)

50 (1.97)

84 (3.31)

120 (4.72)

8 (0.31)

18 (0.71)

125 (4.92)

A0040316

 4 Assembly holder. Dimensions: mm (in)

5.1.2 Mounting instructions

A bypass line can be shut off without interrupting the process. Sensors can be cleaned,

for example, without this adversely affecting the process. For this reason, installation in

the bypass is preferable to direct installation in the process line.

Shutoff valves must be provided by the customer.

1. Mount the product vertically.

2. Establish the medium connection with commercially available clamp fittings (8 mm).

3. If using a chlorine sensor:

Install a DN5-8 spigot downstream from the assembly outlet to take samples for a

reference measurement.

NOTICE

Medium pressure too high

Damaged or functionally impaired assemblies and sensors!

‣Observe the maximum permitted medium pressure for assemblies and sensors.

‣Do not exceed the maximum permitted pressure of 1.5 bar (21.8 psi).

71399069 Installation

Endress+Hauser 9

5.2 Measuring system

A complete measuring system comprises:

• Transmitter, e.g. Liquiline CM444

• Sensor and power supply cable

• Sensor, e.g. CPS11D pH sensor or CUS52D turbidity sensor

• Assembly 71399069

• Optional:

• Inlet stop cock

• Flowmeter

• Flow reducer

• Additional sensors, e.g. oxygen or chlorine sensor

A0037151

 5 Measuring system (example)

1 Transmitter Liquiline CM44x

2 Sensor and power supply cable

3 pH, ORP, andchlorine sensor

4 Assembly with holder

5 Flow reducer

6 Inlet stop cock

7 Turbidity sensor CUS52D

Installation 71399069

10 Endress+Hauser

5.3 Mounting the assembly

5.3.1 Wall mounting

Mark the bore holes.

Drill the holes (4 x M8).

Mount the assembly holder.

4. Where necessary:

Shorten any hoses that are too long.

Mount the flowmeter, along with the hose and stop cock, below the assembly on the

wall. Connect the hose to the inlet of the assembly.

71399069 Installation

Endress+Hauser 11

Mount the outlet hose, along with the flow reducer, on the assembly cover (on the

housing).

7. Not illustrated:

Mount inlet and outlet valves (medium line/bypass) under the assembly.

5.3.2 Panel mounting on the wall

The wall mounting kit contains distance sleeves for mounting the unit on a wall.

The panel features 8 bore holes for wall mounting.

NOTICE

Wall has insufficient load-bearing capacity or unsuitable fastening materials are used

Damage to the wall or panel is possible!

‣Only mount on walls with sufficient load-bearing capacity and select suitable wall

plugs.

1. Mark the bore holes. Dimensions:

2. Drill the mounting holes in the wall. Insert suitable wall plugs.

3. Use distance sleeves and screw the panel in place at the mounting holes.

5.3.3 Panel mounting with stand support

‣Mount the stand according to the instructions in the manual provided.

5.4 Mounting the cover

NOTICE

Cover mounted incorrectly

Sensor may break!

‣Always mount the cover in the correct position.

‣Pay attention to the marks on the assembly housing and on the cover (→  6).

A0037113

 6 Marks on the cover

Installation 71399069

12 Endress+Hauser

5.5 Mounting the sensor

In the case of versions with panel mounting, the sensors are already mounted with the

exception of pH or chlorine sensors.

If the sensors are not already mounted or the slot is not required, the slot is sealed with a

dummy cover on delivery.

5.5.1 Turbidity sensor (clamp version 2'')

Release the clamp fitting and remove the dummy cover from the sensor connection.

Fit a seal over the sensor.

Insert the sensor into the adapter.

Align the sensor optics: 180 ± 10° in relation to the flow direction. Use the arrow on

the sensor to align the optics (arrow at 12 o'clock).

71399069 Installation

Endress+Hauser 13

Fit the clamp fitting around the adapter with the sensor and tighten hand-tight. In

doing so, ensure that the sealing surfaces are free from dirt.

6. Not illustrated:

Connect the sensor cable to the transmitter.

7. No turbidity sensor used:

Seal the adapter with the dummy cover supplied.

5.5.2 Chlorine sensor (1x M35 x 2 version)

1. Remove the dummy plug from the M35 x 2 coupling.

Mount the sensor, along with the O-ring supplied, in the M35 x 2 coupling.

Installation 71399069

14 Endress+Hauser

Tighten the sensor by hand.

Connect the sensor cable to the transmitter.

5. No chlorine sensor used (not illustrated):

Seal the M35 x 2 coupling with the dummy plug provided.

5.5.3 Chlorine sensor (NPT ¾" version, with G1 adapter)

1. Remove the transportation cap from the sensor.

2. Mount the NPT ¾" adapter, along with the sealing tape supplied, in the G1 coupling.

3. Screw the sensor into the adapter.

4. Connect the sensor cable to the transmitter.

5. No sensor used:

Seal the unused coupling with the dummy plug provided.

5.5.4 pH/ORP or oxygen sensor (2x Pg 13.5 x 120 mm)

1. Remove the transportation cap from the sensor and the blanking cover from the Pg

13.5 coupling.

71399069 Installation

Endress+Hauser 15

Mount the sensor in a Pg 13.5 coupling.

Connect the sensor cable to the transmitter.

4. No sensor used (not illustrated):

Seal the unused coupling with the dummy plug provided.

5.6 Post-installation check

1. After mounting, check all the connections to ensure they are secure and leak-tight.

2. Check all hoses for damage.

 Replace damaged hoses.

Commissioning 71399069

16 Endress+Hauser

6 Commissioning

6.1 Preparatory steps

LCAUTION

Process connections and hoses are not tight

Risk of injury if medium escapes!

‣Before applying pressure to the assembly, check that all the connections and hoses are

tight.

1. Check that all seals are fitted correctly.

2. Check the sensor installation and connection.

3. Supply power to the transmitter.

4. Configure the measurement according to the Operating Instructions for the

transmitter.

Operating Instructions for the transmitter

71399069 Maintenance

Endress+Hauser 17

7 Maintenance

LWARNING

Process pressure and temperature, contamination, electrical voltage

Risk of serious or fatal injury!

‣If the sensor has to be removed during maintenance work, avoid hazards posed by

pressure, temperature and contamination.

‣The process line must be unpressurized, empty and rinsed.

‣Before opening, ensure the devices are de-energized.

‣Power can be supplied to switching contacts from separate circuits. Also ensure these

circuits are de-energized prior to carrying out maintenance work.

7.1 Cleaning agent

The choice of cleaning agent depends on the degree and type of contamination. The most

common types of contamination and the appropriate cleaning agents are listed in the

following table.

Type of soiling Cleaning agent

Greases and oils Hot water or water-soluble organic solvents (e.g.

ethanol)

Limescale deposits, metal

hydroxide buildup, lyophobic

biological buildup

Approx. 3% hydrochloric acid

Sulfide deposits Mixture of 3% hydrochloric acid and thiocarbamide

(commercially available)

Protein buildup Mixture of 3% hydrochloric acid and pepsin

(commercially available)

Fibers, suspended substances Pressurized water, possibly surface-active agents

Light biological buildup Pressurized water

LWARNING

Solvents

Solvents are harmful to health, may destroy plastic components of the sensor and are also

suspected carcinogens (e.g. chloroform)!

‣Do not use any halogen-containing, organic solvents or acetone.

NOTICE

Media containing surfactants

Damage to the sensor membrane!

‣The sensor membrane must not come into contact with agents containing surfactants.

7.2 Maintenance tasks

7.2.1 Cleaning the assembly

1. All parts in contact with the medium, such as the sensor and the sensor guide, must

be cleaned regularly. To do so, remove the sensor.

2. Remove light dirt and fouling using a cloth moistened with suitable cleaning

solutions.

Maintenance 71399069

18 Endress+Hauser

3. Remove heavy soiling using a soft brush and a suitable cleaning agent.

4. For very persistent dirt, soak the parts in a cleaning solution. Then clean the parts

with a brush.

7.2.2 Cleaning the sensors

Operating Instructions for the sensor

71399069 Repair

Endress+Hauser 19

8 Repair

8.1 Spare parts

8.1.1 Replacing damaged parts

LWARNING

Incorrect repair

Danger due to damage to the device!

‣Any damage to the assembly that compromises pressure safety must be repaired only

by authorized and qualified personnel.

‣Following repair and maintenance tasks, take appropriate measures to check the

assembly for leaks. Following this, the assembly must again comply with the

specifications in the technical data.

‣Replace all other damaged components immediately.

8.2 Return

The product must be returned if repairs or a factory calibration are required, or if the

wrong product was ordered or delivered. As an ISO-certified company and also due to legal

regulations, Endress+Hauser is obliged to follow certain procedures when handling any

returned products that have been in contact with medium.

To ensure the swift, safe and professional return of the device:

‣Refer to the website www.endress.com/support/return-material for information on the

procedure and conditions for returning devices.

8.3 Disposal

The device contains electronic components. The product must be disposed of as electronic

waste.

‣Observe the local regulations.

9 Accessories

The following are the most important accessories available at the time this documentation

was issued.

‣For accessories not listed here, please contact your Service or Sales Center.

Turbimax CUS52D

• Hygienic Memosens sensor for turbidity measurement in drinking water, process water

and in utilities

• With Memosens technology

• Product Configurator on the product page: www.endress.com/cus52d

Technical Information TI01136C

Accessories 71399069

20 Endress+Hauser

CCS50D

• Membrane-covered amperometric sensor for chlorine dioxide

• With Memosens technology

• Product Configurator on the product page: www.endress.com/ccs50d

Technical Information TI01353C

CCS51D

• Sensor for measuring free chlorine

• With Memosens technology

• Product Configurator on the product page: www.endress.com/ccs51d

Technical Information TI01423C

CCS120D

• Sensor for measuring total chlorine

• With Memosens technology

• Product Configurator on the product page: www.endress.com/ccs120d

Technical Information TI01444C

Memosens CPS31D

• pH electrode with gel-filled reference system with ceramic diaphragm

• Product Configurator on the product page: www.endress.com/cps31d

Technical Information TI00030C

Oxymax COS22D

• Sterilizable sensor for dissolved oxygen

• With Memosens technology or as an analog sensor

• Product Configurator on the product page: www.endress.com/cos22d

Technical Information TI00446C

Memosens CLS82D

• Four-electrode sensor

• With Memosens technology

• Product Configurator on the product page: www.endress.com/cls82d

Technical Information TI01188C

Page is loading ...

Endres+Hauser 71399069/71531419 Operating instructions

Brand: Endres+Hauser

Model: 71399069/71531419

Type: Operating instructions

This manual is also suitable for

71399069

Download PDF

report

Endres+Hauser 71399069/71531419 Operating instructions

This manual is also suitable for

Endres+Hauser 71399069/71531419 Operating instructions

Related papers

Other documents