2. Command access
  3. VLP-UL-M-KIT

Command access VLP-UL-M-KIT Insert Instructions

  • Hello! I am an AI chatbot trained to assist you with the Command access VLP-UL-M-KIT Insert Instructions. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
1
#20375_F
Visit our website for more details
www.CommandAccess.com
U.S. Customer Support
1-888-622-2377
Canada Customer Support
1-855-823-3002
The Command Access VLP-UL-M-KIT is a eld-installable motorized latch-pullback kit
for the Von Duprin 33/35 & 98/99 series devices.
VLP-UL-M-KIT
INSERT INSTRUCTIONS
E.
A.
F.D.
B. C.
KIT INCLUDES | TOOLS REQUIRED
1- Motor Mount w/ MM4S series module
2- 8/32 X 1/4” Phillips head screws
1- 8’ Lead w/ VD Connector
1- Push & go connector
1- MM4S switch program sticker
1- Dogging Hole Cap
• Cordless Drill
• Hammer & Pin Punch(recommend) or 3/16 drill bit
• 5/16 Nut driver (recommended) or Flat head screwdriver
• #2 Phillips head screwdriver
Watch the Video
A.
B.
C.
D.
E.
F.
2
TECHNICAL INFORMATION
MM4S
S
witcheS
ON
OFF
OFF
OFF
ON
OFF
Standard Torque
PTS programming locked
ON ON
High Torque
1 2
P
rogram
PTS Video
Click or Scan
2 Beeps
3 Beeps
5 Beeps
6 Beeps
B
eePS
e
xPlanation
S
olution
Over Voltage
Under Voltage
Retraction or Dogging
failure
Push to Set
> 30V unit will shut down. Check voltage & adjust to 24 V.
< 20V unit will shut down. Check voltage & adjust to 24 V.
Device physically binding during retraction or pulled from the dogged position.
Device is recording it’s new position and power mode after the 6th beep.
trouBleShooting & DiagnoSticS
4 Beeps
Failed Sensor
Verify all 3 sensor wires are installed correctly. Replace sensor if problem
persists by contacting oce.
Make sure to set PTS before nishing installation!
**Important Info**
1. After 1
st
fail: 5 beeps then immediately attempts to retract again.
2. After 2
nd
fail: 5 beeps with pause in-between for 30 seconds then device
attempts to retract again.
3. After 3
rd
fail: 5 beeps every 7 minutes, device will not attempt to retract.
To Reset: Depress bar for 5 seconds at any time.
Setting PTS
Step 1
Select your preferred torque mode (ships in standard torque) Press the device push
pad to the desired setting. (Recommend to fully depress and release 5%, giving the
device room for changing door conditions.)
Step 2
While depressing the push pad, apply power. (i.e. presenting the credential to the reader).
Step 3
Continue to keep pad depressed, the device will beep 6 times. After the beeps have
stopped, release the pad and now the adjustment is complete. If not to your liking
repeat the 3 steps.
Step 4
Once you found the correct location, turn PTS switch to OFF position.
• Average Latch Retraction Current: 2 Amp
• Average Holding Current: 250 mA
High Torque Mode
• Input Voltage: 24VDC +/- 10%
• Wire gauge: Minimum 18 gauge
• Direct wire run - no relays or access control
units in-between power supply & module
• Average Latch Retraction Current: 1 Amp
• Average Holding Current: 215 mA
Standard Torque Mode
SPECIFICATIONS
Low Torque
• Average Latch Retraction Current: 600 mA
• Average Holding Current: 150 mA
Low Torque Mode
Add Program
sticker to inside
of device
3
Ceiling Tile
Legend
Standard Placement
Module
GREEN
CHANNEL 1
LED
NORMALLY OPEN
DRY CONTACT FROM
ACCESS CONTROL
SYSTEM
NO VOLTAGE
LOCKING
HARDWARE
+
-
CAT
ElEctrifiEd Exit dEvicE
InstallatIon ExamplE
rEcommEndEd PowEr SuPPliES:
All Command Access exit devices & field installable kits have been thoroughly cycle
tested with Command Access power supplies at our factory.
For more information click here or go to our website
4
STEP 1 - Disassemble Exit Device
Remove (4) screws on head cover
A.
Remove (2) mounting brackets & (2) screws with
5/16” nutdriver.
B.
Slide off housing from baserail assembly.
C.
Remove push pad by pulling forward & then
upwards.
D.
Remove both screws and skip to Step 3
A.
B
Remove cylinder by pulling up. Push tabs in
& pull up dogging hook.
heaD cover
1
4
2
3
ScrewS
houSing
PuSh PaD
STEP 2- Removing Dogging Assembly - If you have an re rated device skip to step 3
cylinDer
Dogging hook
taBS
1
2
Newer Baserail Older Baserail
5
C.
Utalizing a hmmer and pin punch or drill & 3/16” drill bit remove the (2) rivets.
Depress the baserail’s activating brackets.
A.
Grabbing the motor kit with the attaching hooks facing down move it towards the back activat-
ing bracket at 90°. Grab onto the bottom pin and begin to bring the back of the motor down.
C.
rivetS
Back activating
Bracket
centereD Pin
STEP 3- Installing Kit
rivetS
Keep depressed & nd the bottom roll pin towards
the bottom of the back activating bracket.
B.
Note: if having difculty hooking onto the pin make sure it is centered, if not re-center pin before attaching kit.
6
Continue bringing the motor down until
it’s to the back of the baserail.
D. E.
Slide motor bracket underneath baserail into the
exsisting groves. Pull motor back if neccessaery to
clear the back of the baserail
Once the kit lines up with the screw holes install
(2) Phillips screws provided using a magnetic tip
screw driver.
Next, plug in the push & go connector into the
MM4S
H.
1
2
Connect your VD 8’ lead (CAT or VD retrot) or you can
remove the VD connector to hardwire- take stripped
wire end and push into the push & go connector
Hook up to power & test motor functions before
nishing the re-assembly.
I.
STEP 3- Installing Kit
Continued
7
Replace head cover & re-install (4) screws.
E.
Replace back mounting bracket & re-install
(2) screws with 5/16” nut driver.
C.
PuSh PaD
houSing
Bracket
ScrewS
Bracket
heaD cover
1
4
2
3
Step 1-
Select your preferred torque mode (ships in standard torque) Press the
device push pad to the desired setting.
(Recommend to fully depress and
release 5%, giving the device room for changing door conditions.)
Step 2-
While depressing the push pad, apply power. (i.e. Presenting the
credential to the reader).
Step 3-
Continue to keep pad depressed, the device will beep 6 times. After
the beeps have stopped, release the pad and now the adjustment is
complete. If not to your liking repeat the 3 steps.
Setting PtS
Step 4-
Once you found the correct location, ip the dip switches to o to lock programming.
ON
OFF
OFF
OFF
ON
OFF
Low Torque
Standard Torque
PTS programming locked
ON ON High Torque
1
S
witch
P
rogram
2
Replace push pad by placing over activating arms &
pushing down then back towards end of device
A.
STEP 4- Reassemble your device
Slide baseplate back into housing being careful of
pinching motor/REX wires.
B.
Replace front mounting bracket.
D.
Set PTS isntructions below & add program
sticker to back of the device.
F.
/