2. Command access
  3. CYLP-UL-M KIT

Command access CYLP-UL-M KIT Insert Instructions

  • Hello! I am an AI chatbot trained to assist you with the Command access CYLP-UL-M KIT Insert Instructions. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
1
E.
A.
F.
D.B. C.
G.
Kit Includes Tools Required
1- Motor Mount w/ MM4S series module
1 - Attaching Magnet Bracket
1- 8’ Lead w/ VD Connector
1 - 1/16” Allen Wrench
2- Phillips head screws
1- Push & Go Pigtail
1- Dogging Hole Cap
A.
B.
C.
D.
E.
F.
G.
Cordless Drill
#2 Phillips head screwdriver
CYLP-UL-M KIT
INSERT Instructions
The Command Access CYLP-UL-M-KIT is a field-installable motorized latch-pullback kit for the Corbin
4000/5000 & Yale 7000 series devices.
INSTALL VIDEO
#20092_F
US customer support 1-888-622-2377 | www.commandaccess.com | CA customer support 1-855-823-3002
Step 1-
Select your preferred torque mode (ships in standard torque) Press the device push pad to
the desired setting. (Recommend to fully depress and release 5%, giving the device room for
changing door conditions.)
Step 2-
While depressing the push pad, apply power. (i.e. presenting the credential to the reader).
Step 3-
Continue to keep pad depressed, the device will beep 6 times. After the beeps have stopped, release
the pad and now the adjustment is complete. If not to your liking repeat the 3 steps.
Step 4-
Once you found the correct location, turn PTS switch to OFF position.
Setting PTS
Troubleshooting & Diagnostics
**Important Info**
Make sure to set PTS before finishing installation
Technical Information
mm4s switches
2
on
on
off
STANDARD TORQUE
HIGH TORQUE
PTS PROGRAMMING LOCKED
PTS PROGRAMMING on
off
Average Latch Retraction Current: 2 Amp
Average Holding Current: 250 mA
High Torque Mode
Average Latch Retraction Current: 1 Amp
Average Holding Current: 215 mA
Standard Torque Mode
SPECIFICATIONS
• Input Voltage: 24VDC +/- 10%
• Wire gauge: Minimum 18 gauge
• Direct wire run - no relays or access control
units in-between power supply & module
2 Beeps
3 Beeps
5 Beeps
6 Beeps
Beeps Explanation Solution
Over Voltage
Under Voltage
Retraction or dogging
Push to Start
> 30V unit will shut down. Check voltage & adjust to 24 V.
< 20V unit will shut down. Check voltage & adjust to 24 V.
After 1st fail: 5 beeps then immediately attempts to retract again.
After 2nd fail: 5 beeps with pause in-between for 30 seconds then device
attempts to retract again.
After 3rd fail: 5 beeps every 7 minutes, device will not attempt to retract.
To Reset: Depress bar for 5 seconds at any time.
Device is recording it’s new position and power mode after
the 6th beep.
4 Beeps Failed Sensor Verify all 3 sensor wires are installed correctly. Replace sensor if problem
persists by contacting oce.
MM4S VIDEO
#20092_F
US customer support 1-888-622-2377 | www.commandaccess.com | CA customer support 1-855-823-3002
1
Electrified Exit Device
Installation Example
Ceiling Tile
Legend
Standard Placement
Optional Placement
Module
GREEN
CHANNEL 1
LED
NORMALLY OPEN
DRY CONTACT FROM
ACCESS CONTROL
SYSTEM
NO VOLTAGE
LOCKING
HARDWARE
+
-
CAT
Recommended Power Supplies:
All Command Access exit devices & eld installable kits have been thoroughly
cycle tested with Command Access power supplies at our factory.
For more information click here or go to our website
Retrofit 2-pin Connector
The new 2-pin connector is used when retrofitting a older Command or
Von Duprin installation so you can plug in to the existing connector.
PUSH N’ GO Connector
New
Exisitng
STRIPE WIRE 1/8”-3/16” 7 INSERT INTO WIRE ACCESS HOLES OF CONNECTOR.
WIRE RELEASE
WIRE ACCESS
#20092_F
US customer support 1-888-622-2377 | www.commandaccess.com | CA customer support 1-855-823-3002
1
2
Rod
1 2
Acme Thread
Installation Instructions
Slide o Filler plate.
1.
Install attaching bracket to the rod on the bottom
of the back activating bracket.
3.
Using the 1/16” Hex wrench secure the 1st set
screw to secure the bracket to the device.
5.
Refer to this picture for the next 2 steps.
4.
Use the 2nd set screw to set the height of the
attaching block. You want the block to be level.
6.
If dogging assembly is present, remove (2)
screws and discard dogging assembly.
2.
#20092_F
US customer support 1-888-622-2377 | www.commandaccess.com | CA customer support 1-855-823-3002
Cylindrical housing
Slide the motor mount into the device. Feed the
acme thread into the cylinder clockwise.
7.
Connect your 8’ lead (CAT retrot) or you can remove
the VD connector to hard wire take stripped wire end
and push into the push & go connector.
9.
Hook up to power & set your PTS.
11.
Slide the ller plate back on to re-install
12.
Continue feeding the acme thread until the holes on
the motor mount line up to the existing dogging holes.
Next, install the (2) screws provided.
8.
Next, plug in the push & go connector into
the MM4S.
10.
Installation Instructions
Setting PTS
Step 1-
Select your preferred torque mode (ships in standard torque) Press the device push pad to the
desired setting. (Recommend to fully depress and release 5%, giving the device room for
changing door conditions.)
Step 2-
While depressing the push pad, apply power. (i.e. presenting the credential to the reader).
Step 3-
Continue to keep pad depressed, the device will beep 6 times. After the beeps have
stopped, release the pad and now the adjustment is complete. If not to your liking repeat
the three steps.
Step 4-
Once you found the correct location, ip the dip switches to o to lock programming.
#20092_F
US customer support 1-888-622-2377 | www.commandaccess.com | CA customer support 1-855-823-3002
mm4s switches
2
on
on
off
STANDARD TORQUE
HIGH TORQUE
PTS PROGRAMMING LOCKED
PTS PROGRAMMING on
off
1
/