Livex Lighting 73162-91 Installation guide

Livex Lighting
Brand
Livex Lighting
Model
73162-91
Type
Installation guide

This manual is also suitable for

Livex Lighting 73162-91 is a ceiling mount light fixture that provides ambient lighting for your home. It features a metal pan and a glass shade that gives your room a modern and stylish look. The fixture is easy to install and comes with all the necessary hardware. It requires two medium-base bulbs (not included) and can accommodate up to 60 watts per bulb. The fixture is dimmable, allowing you to adjust the light output to create the perfect ambiance for any occasion. With its sleek design and versatile functionality, the Livex Lighting 73162-91 is a great addition to any home.

Livex Lighting 73162-91 is a ceiling mount light fixture that provides ambient lighting for your home. It features a metal pan and a glass shade that gives your room a modern and stylish look. The fixture is easy to install and comes with all the necessary hardware. It requires two medium-base bulbs (not included) and can accommodate up to 60 watts per bulb. The fixture is dimmable, allowing you to adjust the light output to create the perfect ambiance for any occasion. With its sleek design and versatile functionality, the Livex Lighting 73162-91 is a great addition to any home.

ASSEMBLING &INSTALLATION INSTRUCTIONS PRODUCT#
73162 73163 73164 For Ceiling Mount Fixtures
WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER .
MOUNTING THE FIXTURE
1. Shut off the power at the fuse box or circuit breaker box.
Remove the old fixture from ceiling, including the mounting
plate.
2. Carefully unpack your new fixture and lay out all the parts
on a clear area. Take care not to lose any small parts
necessary for installation.
3. Thread the two mounting screws about 1/4”into the
pre-drilled holes in the mounting plate spaced the same
distance apart as the holes in the pan (A).
4. Attach the mounting plate to the Junction Box using the two
screws from the Junction Box. The side of the mounting
plate marked "GND" must face out.
The junction box is
not include.
5. Hold the pan (A) towards the mounting plate and connect
the electrical wires as follows (See Fig.2). Connect the
black wire from the fixture to the black house (hot) wire;
connect the white wire from the fixture to the white house
(neutral) wire. Make sure all wire nuts are secured. You
may wrap the connections with electrical tape. If your
Junction box has a ground wire (green or bare copper)
connects fixture’s ground wire to it. Other wise attach the
bare copper fixture wire to the green ground screw on the
mounting plate. Tuck the wire connections neatly into the
ceiling junction box as you are holding the fixture
assembly toward the ceiling.
6. Finish mounting the pan (A) by placing it over both
mounting screws so that the screws protrude from the
keyholes in the bottom of the pan (A). Rotate the pan (A)
until the screw are seat in the slots of the keyholes and
tighten it with a screwdriver.
7. Install the light bulbs in accordance with the fixture’s
specifications.
DO NOT EXCEED THE MAXIMUM
WATTAGE RATING!
8. Attach the glass shade(B) to the crown(D), raise the
assembly to the pan , aligning the thread hole of pan with
crown's hole, then tighten it with the screws(C).
Your installation is now complete. Return power to the
junction box and test the fixture.
Fig.1
M
o
u
n
t
i
n
g
p
l
a
t
e
M
o
u
n
t
i
n
g
s
c
r
e
w
G
r
o
u
n
d
W
i
r
e
J
u
n
c
t
i
o
n
B
o
x
A
D
C
(
N
o
t
i
n
c
l
u
d
e
d
)
F
i
x
t
u
r
e
B
G
r
o
u
n
d
W
i
r
e
Fig.2
MIN 90℃ SUPPLY CONDUCTORS
DOC20141273162
White or
HOUSE
Black
WIRES
(Hot)
Smooth
FIXTURE
WIRES
Black or
Ribbed
WIRES
FIXTURE
Bare Copper(Ground)
FIXTURE
WIRES
Copper
(Ground)
HOUSE
(Neutral)
WIRES
White
Bare
Green or
WIRES
HOUSE
  • Page 1 1

Livex Lighting 73162-91 Installation guide

Livex Lighting
Brand
Livex Lighting
Model
73162-91
Type
Installation guide
This manual is also suitable for

Livex Lighting 73162-91 is a ceiling mount light fixture that provides ambient lighting for your home. It features a metal pan and a glass shade that gives your room a modern and stylish look. The fixture is easy to install and comes with all the necessary hardware. It requires two medium-base bulbs (not included) and can accommodate up to 60 watts per bulb. The fixture is dimmable, allowing you to adjust the light output to create the perfect ambiance for any occasion. With its sleek design and versatile functionality, the Livex Lighting 73162-91 is a great addition to any home.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents