This card provides quick start instructions for an experienced
installer to set up and operate the DVI 201xi Tx.
Refer to www.extron.com for the complete user’s guide.
Step 1
Turn off all equipment or disconnect from power sources. Mount the
transmitter and receiver as required.
Step 2
Choose a receiver that is compatible with the DVI 201xi Tx.
Step 3
Determine how the source device will obtain the EDID information
and select one of the following choices.
Procedure A: To capture the EDID of a desired display and store it in
the EDID Minder for future use:
i. Connect the display to the local monitor output of
the transmitter.
ii. Power on the transmitter and the local monitor.
iii. Configure the DDC switches as shown in the figure
at right.
iv. Press and release the EDID "Store" button (see the
figure at right). The rear panel LED turns amber
while the EDID information is read and stored from
the local monitor. Afterwards, the LED turns green.
v. Power off and disconnect the display from the
transmitter.
vi. Connect the transmitter to the receiver.
vii. Connect a source device to the transmitter.
viii. Connect a display device to the receiver and, if required, a local
monitor to the transmitter.
ix. Power on the display device(s), the transmitter, and the receiver.
x. Power on the source device.
Procedure B: To use the default EDID:
i. Configure the DDC switches as shown in the figure
at right.
ii. Connect a source device to the transmitter.
iii. Connect a display device to the receiver and, if
required, a local monitor to the transmitter.
iv. Connect the transmitter and receiver.
v. Power on the transmitter, receiver, and display devices.
vi. Power on the source device.
ON
1 2 3
ON
OFF
DEFAULT EDID
EDID MINDER
REMOTE DDC
ON
1 2 3
ON
OFF
DEFAULT EDID
EDID MINDER
REMOTE DDC
Quick Start Guide — DVI 201xi Tx
68-1645-50
Rev. A
12 08
Procedure C: To use DDC pass-through routed to the local monitor:
i. Configure the DDC switches as shown in the figure at right.
ii. Connect a source device to the transmitter.
iii. Connect a display device to the receiver and, if
required, a local monitor to the transmitter.
iv. Connect the transmitter and receiver.
v. Power on the transmitter, receiver, and local monitor.
vi. Power on the source device.
vii. Power on the source device.
Procedure D: To use DDC pass-through routed to the remote
display:
i. Configure the DDC switches as shown in the figure at right.
ii. Connect a source device to the transmitter.
iii. Connect a display device to the receiver and, if
required, a local monitor to the transmitter.
iv. Connect the transmitter and receiver.
v. Power on the transmitter, receiver, and display
devices.
vi. Power on the source device.
Step 4
The DVI 201xi Tx transmits single link DVI-D (1024x768 or
720p @ 60 Hz up to 200'; 1920x1200 or 1080p @ 60 Hz up to 100') over
two CAT 5/5e/6/7 twisted pair cables.
ON
1 2 3
ON
OFF
DEFAULT EDID
EDID MINDER
REMOTE DDC
ON
1 2 3
ON
OFF
DEFAULT EDID
EDID MINDER
REMOTE DDC
1
2
12V
0.4A MAX
POWER
DVI-D INPUT
LOCAL MONITOR OUTPUT
OUTPUTS
DO NOT
CONNECT
OUTPUTS
TO LAN
SN XXXXXXXX E XXXXX
00/00
DVI DL TX
STORE
EDID
Tx Rx
CONTROL
PASS THRU
ON
1 2 3
ON
OFF
DEFAULT EDID
EDID MINDER
REMOTE DDC
PC w/ Dual Link
DVI Output
Local Monitor
Extron
DVI 201xi Tx
DVI Transmitter
Extron
DVI 201 Rx
Receiver
Projector
Tw isted Pair
Cables (2) 100'
RS-232
DVI 200 RX SERIES
RS-232
PASS THRU
Tx Rx
Extron USA - West
Headquarters
+800.633.9876
Inside USA / Canada Only
+1.714.491.1500
+1.714.491.1517 FAX
Extron USA - East
+800.633.9876
Inside USA / Canada Only
+1.919.863.1794
+1.919.863.1797 FAX
Extron Europe
+800.3987.6673
Inside Europe Only
+31.33.453.4040
+31.33.453.4050 FAX
Extron Asia
+800.7339.8766
Inside Asia Only
+65.6383.4400
+65.6383.4664 FAX
Extron Japan
+81.3.3511.7655
+81.3.3511.7656 FAX
Extron China
+400.883.1568
Inside China Only
+86.21.3760.1568
+86.21.3760.1566 FAX
Extron Middle East
+971.4.2991800
+971.4.2991880 FAX