Teleco Televisore LCD 1511 User manual

USER’S MANUAL

LCD TV SET

1

Contents

 Introduction

 Warning

 Caution

 Main Unit Description

 Remote Control

 OSD basic adjustment

 DTV Features

 USB/CARD Reader Operation

 CI Operation



DVD manual

 Specifications



Trouble Shooting

2

Introduction

Thank you very much for your purchase of our product of LCD TV. It serves as

a normal color TV and PC monitor. To enjoy your set to the full from the very

beginning, read this manual carefully and keep it handy for ready reference.

INSTALLATION

 Locate the receiver in the room where direct light does not strike the screen. Total

darkness or a reflection on the picture screen can cause eyestrain. Soft and indirect

lighting is recommended for comfortable viewing.

 Allow enough space between the receiver and the wall to permit ventilation.

 Avoid excessively warm locations to prevent possible damage to the cabinet or

premature component failure.

 This TV receiver can be connected to DC12V.

 Do not install the receiver in a location near heat sources such as radiator, air ducts,

direct sunlight, or in a place somewhere like close compartment and close area. Do not

cover the ventilation openings when using the set.

 The indicator light will last about 30 seconds to go out after cutting off the electricity, during

this period, you cannot repower it on until the indicator light goes out, thanks a lot for your

attention!

3

Warning

This symbol is intended to alert the user to avoid the risk

of electric shock, do not disassemble this equipment by anyone

except a qualified service personnel.

This symbol is intended to alert the user to the presence

of important operation and maintenance instructions in

the literature accompanying the equipment.

CAUTION: TO AVOID THE RISK OF ELECTRIC SHOCK.

DO NOT REMOVE COVER (OR BACK).

NO USER- SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

4

Caution

High voltages are used in the operation of this product.

- Do not remove the back cabinet from your set. Refer

servicing to qualified service personnel.

Caution

To prevent fire or electrical shock hazard, Do not expose

the main unit to moisture.

Caution

Do not drop or push objects into the television cabinet

slots or openings. Never spill any kind of liquid on the

television receiver.

Caution

Avoid exposing the main unit to direct sunlight and other

source of the heat. Do not stand the television receiver

directly on other produces which give off heat. E. g. video

cassette players, Audio amplifiers. Do not block the

ventilation holes in the back cover. Ventilation is essential

to prevent failure of electrical component. Do not squash

power supply cord under the main unit.

5

Caution

Never stand on, lean on, push suddenly the product

or its stand. You should Pay special attention to

children.

Caution

Do not place the main unit on an unstable cart stand,

shelf or table. Serious injury to an individual, and

damage to the television, may result if it should fall.

Caution

When the product is not used for an extended period

of time, it is advisable to disconnect the AC power

cord from the AC outlet.

Caution

The LCD panel used in this product is made of glass.

Therefore, it can break when the product is dropped

or applied with impact. Be careful not to be injured

by broken glass pieces in case the LCD panel breaks.

6

Main unit description

Control Panel Button Function

TV Terminal Connections

1. USB input terminal. (optional)

2. HDMI input terminal.

3. VGA input terminal of simulation signal of PC.

4. PC AUDIO terminal.

5. SCART input terminal.

6. Video input terminal.

7. AUDIO input terminal.

8. ATV antenna/close circuit TV network port or DTV antenna port.

9. HEADPHONE output terminal.

10. CI input terminal. (optional)

Power Input Configuration

DC

VOL+ : Volume up.

VOL- : Volume down.

CH+ : TV channel up.

CH- : TV channel down.

MENU : Press to select the main menu.

TV/AV : Select the input signal.

POWER : Switch on when at standby mode or enter the standby mode.

7

Optional Configuration as below:

Connect the USB/CARD storage to the USB/CARD

jack on the set.

NOTE

 It is only 500mA MAX of DC current output when you connect with USB jack or CARD

socket.

 To ensure the Mobile HD works well, you should use other power supply for the Mobile HD.

And do not use the USB jack and CARD socket in the same time.

 It supports Mobile HD by connecting with USB jack. The partitions of the Mobile HD can’t be

more than 4 partitions. The max partition is 2TB. It supports FAT/FAT32 document. The max FAT

document is 4GB and the max FAT32 document is 2TB.

8

Remote control

POWER: Press this button to switch on the TV when at

standby mode or enter standby mode.

MUTE: Press this button to mute or restore sound.

DVD SETUP: Press this button to enter the DVD main menu

and press again to exit the main menu.

(Used for models with DVD function only)

TITLE: Press this button to return the title menu.

(Used for models with DVD function only)

MENU(BLUE): Press this button to return the root menu or

exit the DVD main menu.

(Used for models with DVD function only)

USB/CR: Press to select the MEDIA signal source.

(Used for models with USB/CR function only)

NICAM/A2: In the TV condition, press this button to select

the sound mode.

SLEEP: Set the sleep timer.

ASPECT: Press to select the different picture size.

EJECT : press to eject the DVD-disc in DVD mode.

(Used for models with DVD function only)

DISPLAY: Display TV information .

AUTO: Press to adjust the picture automatically in PC mode.

PMODE: Select picture mode.

SMODE: Select sound mode.

DTV: Press to enter the DTV channel.

(Used for models with DTV function only)

SOURCE: Press to change signal source.

ENTER: Enter the selected option or perform the selected

operation. When the current source is DTV, you can

press “ENTER” button to display the “QUICK SELECT”

menu.

MENU: Press this button to enter the main menu for various

optional adjustable setting.

EXIT: Exit the OSD (On-screen display).

0-9: Select and switch to a channel using 0 - 9.

-/--: Switch the program digit.

: Switch back and front between the current and previous

channels.

9

CH-/CH+: Change the channel up and down.

VOL-/VOL+: Adjust the volume.

INFO: Display some information of current program in

DTV mode.

(Used for models with DTV function only)

AUDIO: Press to select the DTV audio or DVD audio.

(Used for models with DTV or DVD function only)

FAV: Switch between custom set “Favourite List”.

(Used for models with DTV function only)

TV/RADIO: Switch between DTV program and radio

program (only audio but not image).

(Used for models with DTV function only)

EPG: Enter electronic program guide.

(Used for models with DTV function only)

Stop playing the disc or Media.

(Used for models with DVD or USB/CR function only)

SUBTITLE(GREEN): Open or close subtitle.

(Used for models with DTV function only)

TEXT: Press to enter the Teletext mode.

(Used for European region only)

Press to start playing the disc or Media, or to pause

playing.

(Used for models with DVD or USB/CR function only)

HOLD: Freeze a multi-page passage on screen in

Teletext mode. (Used for European region only).

Start to record.

INDEX: Press this button to go to the index page in

Teletext.

(Used for European region only)

Press to play backward.

(Used for models with DVD or USB/CR function only)

SIZE: Display the top, bottom or all of page to read

easily in Teletext mode.

(Used for European region only)

Press to play forward.

(Used for models with DVD or USB/CR function only)

10

REVEAL: Press this button to reveal the hidden information

in Teletext page. Press again to hide the information.

(Used for European region only)

Skip to previous chapter

(Used for models with DVD or USB/CR function only)

SUBPAGE: Carry out the function of SUBCODE in the text

while enter the text display mode.

(Used for European region only)

Skip to next chapter

(Used for models with DVD or USB/CR function only)

ZOOM：

：：

：Select the zoom picture.

(Used for models with DVD function only)

GOTO：

：：

：Jump to the appointed chapter or title.

(Used for models with DVD function only)

SUBTITLE(BLUE)：

：：

：Select the disc caption.

(Used for models with DVD function only)

ANGLE：

：：

：Select the angle.

(Used for models with DVD function only)

PROGRAM：

：：

：Select the disc program.

(Used for models with DVD function only)

INTRO：

：：

：Press the button to display the time of chapter

remain or elapsed.

(Used for models with DVD function only)

REPEAT：

：：

：Select the repeat mode.

(Used for models with DVD function only)

AB：

：：

：Select the segment to repeat.

(Used for models with DVD function only)

RED,GREEN,YELLOW, BLUE: Correpond to

the different colored subjects.

(

Used for european region and

USB/CR

function

only

)

11

OSD basic adjustment

Picture

You can select the type of picture, which best corresponds to your viewing.

1. Press the “MENU” button to enter the

OSD menu. Then press “/” button to

select the “PICTURE” menu. Enter the

“PICTURE” menu by pressing “”

button.

2. Press “/” button to select “PICTURE

MODE” and press the “/” button to

select the picture mode.

3. Press “/” button to select

“BRIGHTNESS” and press the “/” button to enter brightness adjustment menu to adjust

brightness.

4. Press “/” button to select “CONTRAST” and press the “/” button to enter contrast

adjustment menu to adjust contrast.

5. Press “/” button to select “SATURATION” and press the “/” button to enter color

adjustment menu to adjust saturation.

6. Press “/” button to select “SHARPNESS” and press the “/” button to enter sharpness

adjustment menu to adjust sharpness.

7. Press “/” button to select “HUE” and press the “/” button to enter hue adjustment

menu to adjust hue.

Note: The item hue is only for NTSC

8. Press “/” button to select “COLOR TEMP” menu and press the “/” button to select the

color temp.

Sound

You can select the type of sound, which best corresponds to your listening.

1. Press the “MENU” button to enter the

OSD menu. Then press “/” button to

select the “SOUND” menu. Enter the

“SOUND” menu by pressing “” button .

12

2. Press “/” button to select “SOUND MODE” and press the “/” button to select the local

sound mode.

3. Press “/” button to select “BASS” and press the “/” button to enter bass adjustment

menu to adjust bass.

4. Press “/” button to select “TREBLE” and press the “/” button to enter treble

adjustment menu to adjust treble.

5. Press “/” button to select “BALANCE” and press the “/” button to enter balance

adjustment menu to adjust balance.

6. Press “/” button to select “AVL” and press the “/”button to select the avl function on

or off.

FUNCTION

You can make the desired adjustment in the TV mode.

1. Press the “MENU” button to enter the

OSD menu. Then press “/” button to

select the “FUNCTION” menu. Enter the

“FUNCTION” menu by pressing “”

button.

2. Press “/” button to select

“LANGUAGE” menu and press the

“/” button to select the OSD language

which you desire.

3. Press “/” button to select “OSD DURATION” and press the “/” button to select the

time how long you want OSD display.

4. Press “/” button to select “ASPECT RATIO” menu and press the “/” button to select

the size which you desire.

5. Press “/” button to select “TT LANGUAGE” menu and press the “/” button to select

the local TELETEXT LANGUAGE.

6. Press “/” button to select “BLUE

SCREEN” and press the “/”button to

select the blue background on or off.

7. Press “/” button to select “RESET”,

then press “ENTER” button to enter. Press

the “/” button to select “YES” or

“NO”.

ATV

1. Press the “MENU” button to enter the

OSD menu. Then press “/” button to

select the “ATV” menu. Enter the “ATV”

13

menu by pressing “” button.

2. Press “/” button to select “AREA” and press the “/” button to select the local country.

3. Press “/” button to select “AUTO

SEARCH” and press the “ENTER” button

to enter. Press “/” button to select

“YES” or “NO”.

4. Press “/” button to select “MANUAL

SEARCH” and press the “ENTER” button

to enter.

a. CHANNEL

Press “/” button to select

“CHANNEL” and press the “/”

button to select the different channel .

b. COLOR SYSTEM

Press “/” button to select “COLOR

SYSTEM” and press the “/” button to

select the local color system .

c. SOUND SYSTEM

Press “/” button to select “SOUND

SYSTEM” and press the “/” button to

select the local sound system .

d. FINE TUNE

Press “/” button to select “FINE TUNE” and press the “/” button to select the

frequency which you want to fine tune .

e. SKIP

Press “/” button to select “SKIP” and press the “/”button to select skip the channel on

or off.

f. MANUAL SEARCH

Press “/” button to select “MANUAL SEARCH” and press the “/” button to adjust the

channel’s frequency .

5. Press “/” button to select “CHANNEL

EDIT” and press the “ENTER” button to

enter.

a. Press “/” button to select one

channel and press “RED” button to pitch

on. Press “/” button to select another

channel which you want to swap . Press

“ENTER” button to confirm.

b. Press “/” button to select one channel and press “GREEN” button to pitch on. Press

“/” button to select another channel which you want to insert . Press “ENTER” button to

confirm.

c. Press “/” button to select one channel and press “YELLOW” button to pitch on. Press

14

“/” button to select another channel which you want to copy. Press “ENTER” button to

confirm.

d. Press “/” button to select the channel which you want to delete and press “BLUE”

button to pitch on. Press “ENTER” button to confirm.

e. Press “/” button to select the channel in the list, press “ENTER” button to enter the

rename channel’s window.

Input channel name at “____”, press

“//” button to select “letter”,

“number”, “_”, “”, “”, “EMPTY” or

“BAK SPC”, and press “ENTER” button

to confirm.

Press “//” button to select “OK”

to save and return to the previous menu.

Press “//” button to select

“CANCEL” to exit and return to the

previous menu.

PC

1. Press the “MENU” button to enter the

OSD menu. Then press “/” button to

select the “PC” menu. Enter the “PC”

menu by Pressing “” button.

2. Press “/” button to select

“H POSITION” menu and press the

“/” button to enter H Position

adjustment menu to adjust H Position.

3. Press “/” button to select

“V POSITION” and press the “/” button to enter V Position adjustment menu to adjust

V Position .

4. Press “/” button to select “PHASE” and press the “/” button to enter Phase adjustment

menu to adjust phase.

5. Press “/” button to select “CLOCK” and press the “/” button to enter clock adjustment

menu to adjust clock.

6. Press “/” button to select “AUTO ADJUST” menu and press the “ENTER” button to do

auto adjustment.

DTV

1. Press the “MENU” button to enter the

OSD menu. Then press “/” button to

select the “DTV” menu when the current

15

signal source is in DTV. Enter the “DTV” menu by Pressing “” button.

2. Press “/” button to select “AREA”

menu and press the “/” button to select

the local country.

3. Press “/” button to select “AUTO

SEARCH” and press the “ENTER” button

to enter. Press “/” button to select

“YES” or “NO”.

4. Press “/” button to select “MANUAL

SEARCH” and press the “ENTER” button

to enter. Press “/” button to select “YES” or “NO”.

5. Press “/” button to select

“CH.MANAGE” and press the “ENTER”

button to enter.

6.

a. CH.ORGN

Press “/” button to select “CH.ORGN” and

press the “ENTER” button to enter . Press

“/” button to select the channel . Press

“RED” button to set the channel for favourite

channel. Press “GREEN” button to delete the

channel. Press “YELLOW” button to skip the

channel. Press “BLUE” button to lock the

channel and the default password is “0000”.

Press “ENTER” button to save.

*The administrator password is “8888”.

b. CH.SORT

Press “/” button to select “CH.SORT” and

press the “ENTER” button to see the channel’s

sort .

c. CH.GROUP

The left side of CHANNEL GROUPING

window lists index number and program name.

Besides, the FAVOURITE lable and GROUP

NUMBER are also listed. All programs can be

grouped as:1 None; 2 News; 3 Science; 4 Sports;

5 Movie; 6 kids; 7 Music and 8 Fashion.

User can move cursor to the program and press the number button to set the group number. Press

“EXIT” button to exit. Press “ENTER” button to save the setting. When the setting is successful,

“Successfully updated…”will be displayed on the screen.

Note: Press the “ENTER” button to display the list of “Channel Grouping”. Press the “/” button

16

to select the group and press the “/” button to select the channel you want.

d. DEL TV CH.

Press “/” button to select “DEL TV CH. ”

and press the “ENTER” button to enter . Press

“/” button to select “YES” or “NO”, press

“ENTER” button to delete all TV channels

when select “YES”, press “ENTER” button to

return back to the previous menu when select

“NO”.

e. DEL RADIO CH.

Press “/” button to select “DEL RADIO

CH. ” and press the “ENTER” button to enter .

Press “/” button to select “YES” or “NO”,

press “ENTER” button to delete all radio

channels when select “YES”, press “ENTER”

button to return back to the previous menu

when select “NO”.

7. Press “/” button to select “TIME” and

press the “ENTER” button to enter.

8. Press “/” button to select “ADV

SETTING” and press the “ENTER” button

to enter.

a. AUDIO

Press “/” button to select “AUDIO” and

press the “/” button to select the local

country .

b. SUBTITLE

Press “/” button to select “SUBTITLE”

and press the “/” button to select the local

country .

c. CI

Press “/” button to select “CI” and press the “ENTER” button to enter .

d. PARENT LOCK

When the password of parental Lock needed to

be changed, user can enter the “Parental Lock”

to change the password. The default password

is “0000” and the administrator password is

“8888”.

e. RATING

When user want to change or set the rating of program, first need to input the correct password.

Press the “/” button to exit/enter the rating option and press the “/” button to select the

rating .

17

f. RECORD SET.

(1) RECORD START

Press “/” button to select “RECORD

START” and press the “ENTER” button to

start record .

(2) FILE MANAGER

Press “/” button to select “FILE

MANAGER” and press the “ENTER” button

to enter. Press “/” button to select the

record . Press “RED” button to play. Press

“GREEN” button to delete one record which

you select. Press “YELLOW” button to delete

all records. Press “BLUE” button to zoom in or

zoom out the picture.

(3) DEVICE LIST

Press “/” button to select “DEVICE LIST”

and press the “ENTER” button to display the

list of device .

(4) SUBSCRIBE

Press “/” button to select “SUBSCRIBE” and press the “ENTER” button to enter. Press “/”

button to select “Timer NO” and press the “”

button to move cursor to the right side of the

window . Press “/” button to select the

number and press “ENTER” button to confirm.

Press “/” button to select “Timer Mode” and

press the “/” button to select the timer mode

such as Off, Once, Daily, Weekly .

18

DTV Features

Favourite List

When the source is selected as DTV, users

can enter “FAVOURITE LIST” by pressing

“FAV” button. The “Favourite LIST” window is

illustrated as follow:

Program Information

When the source is selected as DTV, you

can press “INFO” button to display the channel’s

information. Press “INFO” button twice to

display the channel’s detail. The “PROGRAM

INFORMATION ”window is illustrated as

follow:

Audio

When the source is selected as DTV, users

can enter “Multi audio” by pressing “AUDIO”

button. The “Multi audio” window is illustrated

as follow:

Press “/” button to select “Stereo”  “Left”

 “ Right ”. Press “EXIT” button to exit the

window and save the setting.

Electronic Program Guide



EPG





Electronic Program Guide provides program information which will be broadcasted now or in the

future. The system will display “EPG” window by pressing “EPG” button. DATE and TIME

information is displayed on the top-right of the window. The left side contains all channels. The

right side contains the programs in the channel. The selected program is also displayed on the

bottom-left of the window.

Daily Mode

The “RED” button enables the “DAILY

MODE”, the program guide is listed and sorted

by daily time.

19

Weekly Mode:

The “GREEN” button enables the

“WEEKLY MODE”, the program guide is

listed and sorted by weekly time.

Extend Mode:

The “YELLOW” button enables the

“EXTEND MODE”, the program guide

window contains detailed information about

the program.

“EPG” is used for enter or closing the

“EPG” window.

DTV / Radio Switch

“TV / RADIO” button is used for

switch DTV program and radio.

Subtitle

When the source is selected as DTV,

users can enter subtitle by pressing

SUBTITLEbutton. The subtitle window

is illustrated as follow:

The “Subtitle” language can be turned

ON/OFF by pressing the “/” button.

Page is loading ...

Teleco Televisore LCD 1511 User manual

Teleco Televisore LCD 1511 User manual

Related papers

Other documents