King Canada 8338063 User manual

Brand: King Canada

Model: 8338063

Type: User manual

INSTRUCTION MANUAL

MODEL: 8338063

SAFETY GUARD WITH LIMIT SWITCH

Designed to fit NOVA Voyager DVR Drill Press

(model 58006)

WARRANTY INFORMATION

2-YEAR

LIMITED WARRANTY

FOR THIS SAFETY GUARD

KING CANADA TOOLS

OFFERS A 2-YEAR LIMITED WARANTY

FOR NON COMMERCIAL USE.

PROOF OF PURCHASE

Please keep your dated proof of purchase for warranty and servicing purposes.

LIMITED TOOL WARRANTY

King Canada makes every effort to ensure that this product meets high quality and

durability standards. King Canada warrants to the original retail consumer a 2-year

limited warranty as of the date the product was purchased at retail and that each

product is free from defects in materials. Warranty does not apply to defects due

directly or indirectly to misuse, abuse, normal wear and tear, negligence or

accidents, repairs done by an unauthorized service center, alterations and lack of

maintenance. King Canada shall in no event be liable for death, injuries to persons

or property or for incidental, special or consequential damages arising from the use

of our products.

To take advantage of this limited warranty, return the product at your expense

together with your dated proof of purchase to an authorized King Canada service

center. Contact your retailer or visit our web site at www.kingcanada.com for an

updated listing of our authorized service centers. In cooperation with our authorized

serviced center, King Canada will either repair or replace the product if any part or

parts covered under this warranty which examination proves to be defective in

workmanship or material during the warranty period.

NOTE TO USER

This instruction manual is meant to serve as a guide only. Specifications and

references are subject to change without prior notice.

KING CANADA INC. DORVAL, QUÉBEC, CANADA H9P 2Y4

www.kingcanada.com

ASSEMBLY

Figure 1

Assembly

Note: The following instructions use the

Voyager DVR Drill Press model 58006 for the

Safety Guard installation procedures.

1) Remove the quick release nut (A) Fig.1.

2) Loosen and remove the cap screw (A) Fig.2

which secures the depth stop mount (B).

Slide the depth stop mount downwards and

remove it.

3) Slide the depth stop mount (A) Fig.3 of the

Safety Guard assembly onto the Drill Press

quill. Make sure the depth stop rod (B) was

positioned inside the bracket (C) first as

shown in Fig.3. Secure the depth stop

mount (A) to the quill using the same cap

screw (A) Fig.2 removed previously.

4) Reinstall the previously removed quick

release nut (A) Fig.4 on the depth stop rod

(B) as shown.

Figure 2

Figure 3

Figure 4

ASSEMBLY & ADJUSTMENTS

Figure 5

Figure 6

Assembly

5) Now the limit switch cable with connector (A)

Fig.5 must be connected to the connector

(B) found under the control panel. Remove

rubber cap (C), align the connector holes

with the pins and push to connect.

6) This safety guard comes with a guard

extension (A) Fig.6. Install guard extension

to the main guard (B) as shown using the

supplied lock knobs (C) and hex. bolts.

Adjustments

Adjusting the Safety Guards Height

The position of the safety guards can be

adjusted vertically to cover a range of different

sized chucks and tools.

1) To adjust the safety guard height, loosen the

lock knob (A) Fig.7 on the left side, then

adjust the vertical position of the safety

guard (B) and retighten the lock knob. To

adjust the guard extension height, loosen the

lock knobs (C) on both sides, then adjust the

vertical position of the guard extension (D)

and retighten the lock knob.

Note: The entire chuck body must be covered

by the Safety Guard/Guard Extension.

When the Safety Guard is opened, the Drill

Press will automatically detect the Safety Guard

is open and will turn off the machine. The Drill

Press can only be operated while the Safety

Guard is completely closed.

Figure 7

UPLOADING REQUIRED

FIRMWARE

Safety Guard Firmware- Required Upload

Note: The Voyager DVR Drill Press (model 58006) does NOT come with the necessary

firmware to operate this Safety Guard with Limit Switch. The firmware version of the HMI

can be upgraded via USB cable accessory (included with the Voyager DVR Drill Press)

and a PC computer with internet access. Follow these basic instructions for uploading

required firmware.

1) Go to www.teknatool.com

web site.

2) Click on “Support” tab (1), then click on “Upgrade Your DVR Firmware” tab (2) as shown

below.

3) In order to upload new Firmware, an Uploader Software must be downloaded first.

Download software (3), uncompress folder and install software.

4) Download the required firmware for the Voyager DVR called EU - R2P05x CG - 2018-

05-02 (4). Once downloaded, uncompress folder to access Firmware file.

5) Connect the USB cable (included with the Voyager DVR Drill Press) from your com-

puter to the plug found

under the control panel.

6) Launch Uploader

Software. Press F1 then

ON buttons on control

panel to establish

communication. LCD

will indicate “SJM

Device in DFU Mode”.

7) From the menu, click on

“choose” and select the

Firmware file you

uncompressed earlier.

8) Click “upgrade”. The

firmware upgrade will

begin loading, and you will be notified when the process has finished. Installation is

finished.

Firmware Test

At this point, it is important to make sure the firmware upgrade was successful by testing

the safety guard. Turn machine on, open the safety guard. The machine must stop and

the LCD screen will indicate “Safety Guard Open”. The drill press will not be able to start

again until the safety guard is completely closed.

PARTS DIAGRAM & PARTS LISTS

Refer to the Parts section of the King Canada web site for the most updated parts

diagram and parts list.

King Canada 8338063 User manual

King Canada 8338063 User manual

King Canada 8338063 User manual

Related papers

Other documents