Magnetrol E3 Modulevel Retrofit User manual

Brand: Magnetrol

Model: E3 Modulevel Retrofit

Type: User manual

Magnetrol E3 Modulevel Retrofit offers advanced features for precise level measurement. It boasts a sleek design with a dual-compartment angled housing, reducing size and weight while providing a modern look. Its versatility allows retrofitting onto existing Modulevel or into Modulevel or other manufacturer's chambers. The device supports various communication protocols, including HART, AMS, PACTware, and FOUNDATION fieldbus, enabling seamless integration into existing systems.

E3 Modulevel

Retrofits

n E3 Transmitter Head Onto

Existing Electronic Modulevel

n E3A or E3B Head Into

Existing Modulevel Chamber

n E3A or E3B Head Into

Existing Torque Tube Transmitter Chamber

Remove Install

The new E3 electronic Modulevel incorporates many

advances not previously available in a displacer transmitter.

This exciting product offers communications via a variety

of platforms; three-button keypad and two-line ¥ eight-

character LCD display, HART

communications, AMS,

PACTware or F

OUNDATION fieldbus

™

. The use of the dis-

tinctive Eclipse

dual-compartment angled housing results

in a sleek, modernized look, as well as, decreased size and

weight.

The E3 Modulevel is ideal for retrofitting onto an existing

Modulevel or into an existing Modulevel or other manu-

facturer’s chamber.

E3 Transmitter Head Onto

Existing Electronic Modulevel

The E3 transmitter head can be retrofitted onto all existing

EZ, Smart EZ, ES II and E3 sensing units. Order part

number Z39-4101-xxx, where the ninth and tenth digits

are identical to those of the applicable E3 model number

(see bulletin 48-135).

Remove the old transmitter head and install the new head

on the existing enclosing tube (see bulletin 48-697). User

calibration must be performed with E3 head on old sens-

ing unit.

Z39-4101-

n n n

Mounting and Temperature

Housing Material and Agency Approval

Output/SIL Rating

E3A or E3B Head Into

Existing Modulevel Chamber

A top mounted E3 Modulevel can be mounted into an exist-

ing pneumatic or electronic Modulevel chamber. A standard

model E3 can be dropped into an existing blind flange design

chamber (P5x, E5x). If the existing Modulevel has a top-hat

style chamber, a specially modified E3 can be mounted into

the existing top hat design chamber (P6x, E6x).

Order model E3A or E3B for existing blind chamber, or an

XE3A or XE3B, X=special stem length for an existing top-hat

chamber. Remove old Modulevel displacer and top works

from chamber and mount the new E3 as you would any top

mounted model (see bulletin 48-635). Simple configuration

must be performed (no calibration required).

E3A or E3B Head Into

Existing Torque Tube Transmitter Chamber

A top mounted E3 Modulevel can be mounted into an exist-

ing side/side or side/bottom configuration torque tube cham-

ber.* The unit must be specially modified with a compatible

head flange and stem length adjusted for the torque tube

chamber.

Order model XE3A or XE3B, X=torque-tube flange, special

stem length. Remove the old torque tube top works and

displacer from the chamber and mount the new E3 as you

would any top mounted model (see bulletin 48-635). Simple

configuration must be performed (no calibration required).

BULLETIN: 48-698.2

EFFECTIVE: December 2015

SUPERSEDES: November 2009

Remove Install

45°

Fisher 249B/259B (600 lb.),

carbon steel

45°

Masoneilan (600 lb.),

carbon steel

Ø .875

(22)

Ø 7.25

(184)

Ø 9.0

(229)

1.125

(32)

5.23

(133)

.22

(6)

Ø .875

(22)

Ø 5.875

(149)

Ø 7.50

(191)

.25

(6)

1.125

(29)

4.00

(102)

Proprietary Flanges

E3 cannot be retrofit onto a Fisher 249C chamber.

Remove Install

Magnetrol E3 Modulevel Retrofit User manual

Magnetrol E3 Modulevel Retrofit User manual

Magnetrol E3 Modulevel Retrofit User manual

Related papers

Other documents