Philips BTM2360/12 User manual

Brand: Philips

Model: BTM2360/12

Category: Home audio sets

Type: User manual

www.philips.com/support

BTM2360

User manual

Always there to help you

Question?

Contact

Philips

1EN

Contents

1 Important 2

Safety 2

Notice 2

2 Your Micro Music System 4

Introduction 4

What's in the box 4

Overview of the main unit 4

Overview of the remote control 5

3 Get started 7

Connect speakers 7

Connect power 7

Prepare the remote control 7

Demonstrate the features 8

Power on 8

Set the clock 8

Select a source 9

4 Play 10

Play from disc 10

Play from USB 10

Control play 10

Skip tracks 11

Program tracks 11

Play from Bluetooth-enabled devices 11

5 Listen to the radio 13

Tune to a radio station 13

Program radio stations automatically 13

Program radio stations manually 13

Select a preset radio station 13

6 Adjust sound 14

Select a preset sound effect 14

Adjust volume level 14

Mute sound 14

7 Other features 15

Set the alarm timer 15

Set the sleep timer 15

Listen to an external device 15

Charge your devices 16

8 Product information 17

Specications 17

USB playability information 18

Supported MP3 disc formats 18

9 Troubleshooting 19

2 EN

1 Important

Safety

Read and understand all instructions before

you use this micro music system. If damage is

caused by failure to follow the instructions, the

warranty does not apply.

This 'bolt of lightning' indicates uninsulated

material within the device may cause an

electrical shock. For the safety of everyone in

your household, please do not remove the

covering.

The 'exclamation mark' calls attention to

features for which you should read the enclosed

literature closely to prevent operating and

maintenance problems.

WARNING:Toreducetheriskofreorelectric

shock, the device should not be exposed to rain

ormoistureandobjectslledwithliquids,such

as vases, should not be placed on the device.

CAUTION: To prevent electric shock, fully

insert the plug. (For regions with polarized

plugs: To prevent electric shock, match wide

blade to wide slot.)

Warning

•

Never remove the casing of this apparatus.

• Never lubricate any part of this apparatus.

• Never look into the laser beam inside this apparatus.

• Never place this apparatus on other electrical

equipment.

• Keep this apparatus away from direct sunlight, naked

amesorheat.

• Ensure that you always have easy access to the power

cord, plug or adaptor to disconnect the apparatus from

the power.

• The device shall not exposed to dripping

or splashing.

• Do no place any source of danger on the

device(e.g.liquidlledobjects.litcandles).

• Where the MAINS plug or an appliance

coupler is used as the disconnect device,

the disconnect device shall remain readily

operable.

• Make sure that there is enough free space

around the product for ventilation.

• Battery usage CAUTION – To prevent

battery leakage which may result in bodily

injury, property damage, or damage to the

unit:

• Install all batteries correctly, + and - as

marked on the unit.

• Do not mix batteries (old and new or

carbon and alkaline, etc.).

• Batteries (packed or installed) shall not

be exposed to excessive heat such as

sunshine,reorthelike.

• Remove batteries when the unit is not

used for a long time.

• Onlyuseattachments/accessoriesspecied

by the manufacturer.

Notice

Anychangesormodicationsmadetothis

device that are not expressly approved by

Gibson Innovations may void the user’s

authoritytooperatetheequipment.

Compliance

Hereby, Gibson Innovations declares that

this product is in compliance with the

essentialrequirementsandotherrelevant

provisions of Directive 1999/5/EC. You

canndtheDeclarationofConformityon

www.philips.com/support.

3EN

This apparatus includes this label:

Care of the environment

Disposal of your old product and battery

Your product is designed and manufactured

withhighqualitymaterialsandcomponents,

which can be recycled and reused.

This symbol on a product means that the

product is covered by European Directive

2012/19/EU.

This symbol means that the product contains

batteries covered by European Directive

2013/56/EU which cannot be disposed of with

normal household waste.

Inform yourself about the local separate

collection system for electrical and electronic

products and batteries. Follow local rules and

never dispose of the product and batteries

with normal household waste. Correct disposal

of old products and batteries helps prevent

negativeconsequencesfortheenvironmentand

human health.

Removing the disposable batteries

To remove the disposable batteries, see battery

installation section.

Environmental information

All unnecessary packaging has been omitted.

We have tried to make the packaging easy to

separate into three materials: cardboard (box),

polystyrene foam (buffer) and polyethylene

(bags, protective foam sheet.)

Your system consists of materials which can

be recycled and reused if disassembled by

a specialized company. Please observe the

local regulations regarding the disposal of

packaging materials, exhausted batteries and old

equipment.

The Bluetooth

word mark and logos are

registered trademarks owned by Bluetooth

SIG, Inc. and any use of such marks by Gibson

Innovations is under license.

The making of unauthorized copies of copy-

protected material, including computer

programs,les,broadcastsandsound

recordings, may be an infringement of

copyrights and constitute a criminal offence.

Thisequipmentshouldnotbeusedforsuch

purposes.

Care for your product

• Do not insert any objects other than discs

into the disc compartment.

• Do not insert warped or cracked discs into

the disc compartment.

• Remove the discs from the disc

compartment if you are not using the

product for an extended period of time.

• Onlyusemicroberclothtocleanthe

product.

Note

•

The type plate is located on the back of the product.

4 EN

2 Your Micro

Music System

Congratulations on your purchase, and

welcometoPhilips!Tofullybenetfromthe

support that Philips offers, register your product

at www.philips.com/support.

Introduction

With this unit, you can:

• enjoy audio from discs, USB devices,

Bluetooth devices, and other external

devices;

• listen to radio stations.

You can enrich sound output with below

sound effect:

• Digital Sound Control (DSC)

The unit supports these media formats:

What's in the box

Check and identify the contents of your

package:

• Main unit

• Remote control (with one AAA battery)

• Speaker boxes (×2)

• Short user manual

• Safety and notice

Overview of the main unit

ghijkl m on

ghijkl

m on

• Turn on the product.

• Switch to standby mode or ECO

power standby mode.

b Bluetooth indicator

• Indicate the Bluetooth connection

status.

c Display panel

• Show current status.

5EN

d /

• Skip to previous/next track.

• Search within a track/disc.

• Tune to a radio station.

• Adjust time.

• Start or pause play.

f VOLUME knob

• Adjust volume.

• Open or close the disc compartment.

• Stop play.

• Erase a program.

i Disc compartment

j AUDIO IN

• Connect external audio devices.

k SOURCE/PAIRING

• Press to select a source: DISC, USB,

TUNER, AUDIO IN, BT.

• In Bluetooth mode, press and hold for

three seconds until you hear a beep

sound to disconnect the currently

connected device and enter pairing

mode.

• Connect USB storage devices.

m SPEAKER OUT socket

• Connect with the speakers.

n ANTENNA socket

• Connect with the FM antenna.

o AC MAINS ~

Overview of the remote

control

• Turn the product on or off.

• Switch to standby mode or ECO

power standby mode.

b CD

• Select CD source.

c USB

• Select USB source.

q FM/AUDIO IN

• Select FM source.

• Select AUDIO IN source.

• Select Bluetooth source.

d /

• Skip to the previous/next track.

• Search within a track/disc/USB.

• Tune to a radio station.

• Adjust time.

• Play tracks randomly.

f ALBUM/PRESET

• Select a preset radio station.

• Skip to previous/next album.

g DISPLAY

• Adjust display brightness.

• During playback, display the play

information.

h SLEEP/TIMER

• Set sleep timer.

• Set alarm timer.

i CLOCK

• Set the clock.

• View clock information.

j PROG

• Program tracks.

• Program radio stations.

• Auto store FM radio stations.

• Mute or restore volume.

l SOUND

• Enrich sound effect with Digital Sound

Control (DSC).

m VOL +/-

• Adjust volume.

• Play a track or all tracks repeatedly.

• Stop play or erase a program.

/PAIRING

• Press to start, pause, or resume play.

• Press and hold for three seconds until

you hear a beep sound to enter pairing

mode.

7EN

3 Get started

Caution

•

Use of controls or adjustments or performance of

procedures other than herein may result in hazardous

radiation exposure or other unsafe operation.

Always follow the instructions in this chapter in

sequence.

Connect speakers

Note

•

Insert the stripped portion of each speaker wire into

the socket completely.

• Forbettersoundquality,usethesuppliedspeakersonly.

1 Fortherightspeaker,ndthesocketson

the back of the main unit marked "R".

2 Insert the red wire into the red (+) socket,

and the black wire into the black (-) socket.

3 Fortheleftspeaker,ndthesocketsonthe

main unit marked "L".

4 Repeat step 2 to insert the left speaker

wire.

To insert each speaker wire:

1 Holddownthesocketap.

2 Insert the speaker wire fully.

3 Releasethesocketap.

Connect power

Caution

•

Risk of product damage! Ensure that the power supply

voltage corresponds to the voltage printed on the back

or the underside of the unit.

• Before you connect the AC power cord, ensure that

you have completed all other connections.

Connect the power cable to the wall socket.

Prepare the remote control

Caution

•

Risk of product damage! When the remote control is

not used for long periods, remove the batteries.

To insert the remote control battery:

1 Open the battery compartment.

2 Insert the supplied AAA battery with

correct polarity (+/-) as indicated.

3 Close the battery compartment.

8 EN

Demonstrate the features

In standby mode, press to demonstrate

features of this device.

» The features are displayed one by one

across the display panel.

• To turn off the demonstration, press

again.

Power on

Press .

» The product switches to the last selected

source.

Switch to standby mode

Press again to switch the product to standby

mode.

» The clock (if set) is displayed on the panel.

• In standby mode, press

to switch

between working mode and standby

mode.

Note

•

The product switches to standby mode after

15 minutes inactive.

Switch to ECO power standby mode

Press and hold for more than two seconds.

» The red ECO power standby indicator

turns on.

• In Eco power standby mode, press to

switch between working mode and ECO

power standby mode.

Note

•

The product switches to ECO power standby mode

after 15 minutes in standby mode.

Switch between standby mode and ECO

powerstandby mode:

• Press and hold

for more than two

seconds.

Note

•

If no button is pressed over 15 minutes in standby

mode, this product goes to ECO standby mode

automatically.

Set the clock

In standby mode, press and hold CLOCK

for more than two seconds to enter the

clock setting mode.

» [24H] or [12H] is displayed.

2 Press / to select 24H or 12H hour

format, and then press CLOCK.

» The hour digits begin to blink.

3 Press / to set the hour, and then

press CLOCK.

» The minute digits begin to blink.

4 Press / to set the minute, and then

press CLOCK.

» The set clock is displayed.

Note

•

To view clock information in working mode, press

CLOCK.

• If no button is pressed in 90 seconds during setting,

the product exits clock setting without saving earlier

operations.

9EN

Select a source

On the main music system

Press SOURCE repeatedly to select a source.

• [DISC]: the disc in the disc compartment

• [USB]:.mp3lesstoredontheconnected

USB storage device

• [TUNER]: the FM tuner

• [AUDIO IN]: the audio input through the

AUDIO IN socket

• [BT]: audio on the Bluetooth device

On the remote control

Press CD, FM, USB, orAUDIO IN to select

each source directly.

• CD: the disc in the disc compartment

• FM: the FM tuner

• USB:the.mp3lesstoredonthe

connected USB storage device

• AUDIO IN:the audio input through the

AUDIO IN socket

• BT: audio on the Bluetooth device

10 EN

4 Play

Play from disc

Press CD to select CD source.

2 Press to open the disc compartment.

3 Insert a disc with the label side up.

4 Press to close the disc compartment.

» Play starts automatically. If not, press

Play from USB

Note

•

Make sure that the USB device contains playable audio

content.

1 Insert a USB device into the socket.

2 Press USB to select the USB source.

» Play starts automatically. If not, press

Control play

Start, pause, or resume play.

Stop play.

/ Select an album or a folder.

/ Press to skip to the previous or

next track.

Press and hold to search

backward/forward within a track.

Play a track or all tracks

repeatedly.

Play tracks randomly.

VOL +/- Increase or decrease the volume.

Mute or unmute sound.

SOUND Selectapresetsoundequalizer.

DISPLAY Adjust display brightness.

11EN

Skip tracks

When playing a CD:

Press

/ to select tracks.

When playing an MP3 disc and USB:

1 Press / to select an album or a folder.

2 Press / toselectatrackorale.

Program tracks

This function allows you to program 20 tracks

inthedesiredsequence.

1 In stop mode, press PROG to activate the

program mode.

» [PROG] (program) and [001 PR 01]

are displayed.

2 For MP3 tracks, press / to select an

album.

3 Press / to select a track, and then

press PROGtoconrm.

4 Repeat steps 2 to 3 to program more

tracks.

5 Press to play the programmed tracks.

» During play, [PROG] (program) is

displayed.

To erase the program

Press

twice.

Play from Bluetooth-enabled

devices

Note

•

The effective operation range between the unit and

your Bluetooth enabled device is approximately

10 meters (30 feet).

• Any obstacle between the system and the device can

reduce the operational range.

• Compatibility with all Bluetooth devices is not

guaranteed.

1 Press to select the Bluetooth source.

» [BT] (Bluetooth) is displayed.

» TheBluetoothindicatorashesblue.

2 On your device that supports Advanced

AudioDistributionProle(A2DP),enable

Bluetooth and search for Bluetooth devices

that can be paired (refer to the user

manual of the device).

3 Select 'Philips BTM2360' on your

Bluetooth enabled device and if necessary

input '0000' as the paring password.

» After successful pairing and connection,

the Bluetooth indicator turns solid

blue, and the unit beeps twice.

4 Play audio on the connected device.

» Audio streams from your Bluetooth

enabled device to this product.

• If you fail to search for "Philips

BTM2360'' or cannot pair with

this product, press and hold

SOURCE/PAIRING (or

on the

remote control) for three seconds until

you hear a beep sound to enter pairing

mode.

0000

Philips BTM2360

12 EN

Tip

•

The product can memorize up to 8 previously

connected Bluetooth devices.

To disconnect the Bluetooth-enabled device:

• Deactivate Bluetooth on your device; or

• Move the device beyond the

communication range.

Enter Bluetooth pairing mode

Press and hold SOURCE/PAIRING for three

seconds until your hear a beep sound to

disconnect the currently connected device and

enter Bluetooth pairing mode.

Clear Bluetooth pairing history

• Press and hold on the main set for

8 seconds.

» The current Bluetooth connection is

disconnected.

» After successful clearing, the product

beeps.

13EN

5 Listen to the

radio

Tune to a radio station

Tip

•

Position the antenna as far as possible from TV, VCR, or

other radiation source.

• For optimal reception, fully extend and adjust the

position of the antenna.

1 Press FM/AUDIO IN repeatedly to select

FM source.

2 Press and hold / for more than two

seconds.

» The radio tunes to a station with

strong reception automatically.

3 Repeat step 2 to tune to more stations.

To tune to a weak station:

Press

/ repeatedlyuntilyoundoptimal

reception.

Program radio stations

automatically

Note

•

You can program a maximum of 20 preset radio

stations (FM).

In tuner mode, press and hold PROG for

more than two seconds to activate automatic

programming.

» All available stations are programmed in the

order of waveband reception strength.

» Therstprogrammedradiostationis

broadcast automatically.

Program radio stations

manually

Tune to a radio station.

2 Press PROG to activate program mode.

» [PROG] (program) displays on the

screen.

3 Press / to allocate a number from

1–20 to this radio station, and then press

PROGtoconrm.

» Thepresetnumberandthefrequency

of the preset station are displayed.

4 Repeat steps 1-3 to program more

stations.

Note

•

To overwrite a programmed station, store another

station in its place.

Select a preset radio station

In tuner mode, press / to select a preset

number.

14 EN

6 Adjust sound

The following operations are applicable to all

supported media.

Select a preset sound effect

• Press SOUND repeatedly to select a

preset sound effect.

• DSC1, DSC2, DSC3, DSC4, and DSC5

Adjust volume level

• On the remote control, press VOL +/-

repeatedly.

• On the main unit, rotate the volume knob.

Mute sound

• Press to mute or unmute the sound.

15EN

7 Other features

Set the alarm timer

This product can be used as an alarm clock. You

canselectthedisc,FM,or.mp3lesonaUSB

storage device as alarm source.

Note

•

Make sure that you have set the clock correctly.

• If the selected alarm source is unavailable, this product

switches to FM mode automatically.

1 In normal standby mode, press and hold

SLEEP/TIMER for two seconds.

» The hour digits blink.

is displayed.

2 Press / repeatedly to set the hour,

and then press SLEEP/TIMERtoconrm.

» The minute digits blink.

3 Press / to set the minute, and then

press SLEEP/TIMERtoconrm.

» The last selected alarm source blinks.

4 Press / to select an alarm source

(DISC, USB or Tuner), and then press

SLEEP/TIMERtoconrm.

» VOL_XX (XX indicates the volume

level of alarm) blinks.

5 Press / to set the alarm volume,

and then press SLEEP/TIMERtoconrm.

Activate/deactivate alarm timer

In standby mode, press SLEEP/TIMER

repeatedly to activate or deactivate timer.

» If timer is activated,

is displayed.

Tip

•

Alarm timer is not available in AUDIO IN mode.

Note

•

If CD/USB source is selected, but no disc is placed

or no USB device is connected, the TUNER source is

selected automatically.

Set the sleep timer

This music system can switch to standby

automatically after a set period of time.

• When the music system is turned on, press

SLEEP/TIMER repeatedly to select a set

period of time (in minutes).

» When sleep timer is activated,

displayed.

To deactivate sleep timer

• Press SLEEP/TIMER repeatedly until [OFF]

(sleep off) is displayed.

» When sleep timer is deactivated,

disappears.

Listen to an external device

You can listen to an external device through this

unit with an MP3 link cable.

1 Connect an MP3 link cable (not supplied)

between:

• AUDIO IN jack (3.5 mm) on the

product,

• and the headphone jack on an external

device.

2 Press FM/AUDIO IN repeatedly to select

AUDIO IN source.

3 Start to play the device (see the device

user manual).

16 EN

Charge your devices

With this micro music system, you can charge

your external devices, such as your cell phone,

MP3 player or other mobile devices.

1 Use a USB cable to connect the USB

socket of product with the USB socket of

your devices.

2 Connect the product to power.

» Once the device is recognized, the

charging starts.

AUDIO IN

Note

•

Philips does not guarantee the compatibility of this

product with all devices.

17EN

8 Product

information

Note

•

Product information is subject to change without prior

notice.

Specications

Amplier

Total Output Power Maximum 70W

FrequencyResponse 60 Hz - 20 kHz;

±3 dB

Signal to Noise Ratio ≥75dBA

Total Harmonic

Distortion

< 1%

Aux Input 600 mV ± 100 mV

RMS 22kohm

Speakers

Speaker Impedance 8 ohm

Speaker Driver 20mm Tweeter,

100mm Woofer

Sensitivity 83 ± 3dB/m/W

Tuner (FM)

Tuning Range 87.5-108 MHz

Tuning grid 50 KHz

Sensitivity

- Mono, 26dB S/N Ratio

- Stereo, 46dB S/N Ratio

<22 dBf

<45 dBf

Search Selectivity <30 dBf

Total Harmonic

Distortion

<3%

Signal to Noise Ratio >45 dB

USB

USB Direct Version 2.0 Full Speed

Charging support 5V, 500mA

Disc

Laser Type Semiconductor

Disc Diameter 12 cm/8 cm

Support Disc CD-DA, CD-R, CD-

RW, MP3-CD

Audio DAC 24 Bits/44.1 KHz

Total Harmonic

Distortion

<3% (1 KHz)

FrequencyResponse 20 Hz - 20 kHz

(44.1 KHz)

S/N Ratio ≥80dBA

Bluetooth

Bluetooth Version V4.0

BluetoothFrequency

Band

2.4 GHz ~ 2.48 GHz

ISM Band

Bluetooth Range 10 m (free space)

General information

AC power 220-240 V~, 50/60 Hz

Operation Power

Consumption

<25 W

Eco Standby Power

Consumption

<0.5 W

Dimensions

- Main Unit

(W x H x D)

- Speaker Box

(W x H x D)

180 x 121 x 227 mm

140 x 260 x 182 mm

Weight

- Main Unit

- Speaker Box

1.62 kg

1.72 kg x 2

18 EN

USB playability information

Compatible USB devices:

• USBashmemory(USB2.0orUSB1.1)

• USBashplayers(USB2.0orUSB1.1)

• memorycards(requiresanadditionalcard

reader to work with this unit)

Supported USB formats:

• USBormemoryleformat:FAT12,FAT16,

FAT32 (sector size: 512 bytes)

• MP3 bit rate (data rate): 32-320 Kbps and

variable bit rate

• Directory nesting up to a maximum of

8 levels

• Number of albums/ folders: maximum 99

• Number of tracks/titles: maximum 999

• File name in Unicode UTF8 (maximum

length: 32 bytes)

Unsupported USB formats:

• Empty albums: an empty album is an album

thatdoesnotcontainMP3/WMAles,and

will not be shown in the display.

• Unsupportedleformatsareskipped.

For example, word documents (.doc) or

MP3leswithextension.dlfareignored

and not played.

• WMA,AAC,WAV,PCMaudioles

• DRMprotectedWMAles(.wav,.m4a,

.m4p, .mp4, .aac)

• WMAlesinLosslessformat

Supported MP3 disc formats

• ISO9660, Joliet

• Maximum title number: 128 (depending on

lenamelength)

• Maximum album number: 99

• Supportedsamplingfrequencies:32kHz,

44.1 kHz, 48 kHz

• Supported Bit-rates: 32~256 (kbps),

variable bit rates

Page is loading ...

Philips BTM2360/12 User manual

Brand: Philips

Model: BTM2360/12

Category: Home audio sets

Type: User manual

Download PDF

report

Philips BTM2360/12 User manual

Philips BTM2360/12 User manual

Related papers

Other documents