Lopi 33 DVI Gas Fireplace Insert Operating instructions

Lopi
Brand
Lopi
Model
33 DVI Gas Fireplace Insert
Category
Fireplaces
Type
Operating instructions

This manual is also suitable for

Lopi 33 DVI Gas Fireplace Insert: Experience the warmth and ambiance of a traditional fireplace with the convenience of gas. Enjoy adjustable flame height, variable heat output, and remote control operation for effortless temperature management. Create a cozy atmosphere in any room with this versatile insert, designed to fit seamlessly into your existing fireplace. Its compact size and clean-face design make it a stylish addition to any home.

Lopi 33 DVI Gas Fireplace Insert: Experience the warmth and ambiance of a traditional fireplace with the convenience of gas. Enjoy adjustable flame height, variable heat output, and remote control operation for effortless temperature management. Create a cozy atmosphere in any room with this versatile insert, designed to fit seamlessly into your existing fireplace. Its compact size and clean-face design make it a stylish addition to any home.

Surround Panels (DVS/DVL EF II)
Page 1 of 2 17601428 - 2/25/14 © Travis Industries, Inc.
Compatibility
DVS Insert EF II
DVL Insert EF II
Packing List
Top, Right, and Left Side Panels
Panel Trim (with Hardware)
(4) 10-24 Type F Thread-Cutting Screws
(7) Spring Clips
Part Numbers
DVS – 4” by 6” 96100300
DVS – 8” by 10” 96100301
DVS – 10” by 13” 96100302
DVL – 4” by 6” 96100320
DVL – 8” by 10”” 96100321
DVL – 10” by 13” 96100322
Arched Faces with Screens (2014 or later) Require Use of the Extended Position Holes
This surround panel has 2 sets of holes. Hole position is
determined by the face being used (see below)
Standard Position – used for all faces except for the new
2014 arched faces with screens. All other faces use the
standard position hole. If you are uncertain, use the standa
r
position.
Extended Position – used only for new arched faces with
screens (2014 or later). The extended position allows room
the screen and eliminates the ½” gap to the panel. The
extended position hole positions the insert ½” farther into th
e
fireplace cavity.
Rheostat and On/Off Switch Placement on 33 DVI/31 DVI
Install the rheostat and On/Off switch on the right surround side surround panel (see the Owner’s Manual for details).
Inside Fit Panels
The panels may be cut down in size and placed within the fireplace opening. When installed in this configuration, install the
rheostat and on/off switch in the control panel under the firebox (see the owner’s manual for details). For standard installations, we
recommend you attach the rheostat and on/off switch to the upper right surround panel trim (after the trim is installed).
Installation
Before installation the insert should be in place with the gas line and vent attached. Pull the insert out slightly to assist in the
installation. Attach the side panels then the top panel and trim (see the directions below and on the following page).
DVS / 31 DVI
Side Panel Installation
Extended
Position
Standard
Position
DVS Side
Panel
DVL Side
Panel
Line up each side surround
panel and insert two screws from
the inside to secure in place.
5/16" Nutdriver
Pre-thread the holes on the brackets
screws included in the surround panel kit.
b
a
Run the power cord to
the side of the insert.
Surround Panels (DVS/DVL EF II)
Page 2 of 2 17601428 - 2/25/14 © Travis Industries, Inc.
DVL / 33 DVI – Side Panel Installation
Top Panel and Trim Installation
Line up each side surround
panel and insert two screws from
the inside to secure in place.
5/16" Nutdriver
Pre-thread the holes on the surround
panels with the screws included in the
surround panel kit.
b
a
Run the power cord to
the side of the insert.
Top
Panel
Top Trim
"L" Bracket
Right Side Trim
Slot for on/off
switch and hole for
rheostat
(
31 & 33 DVI Only)
a
"L" Bracket
Right Side
Trim
Top Trim
Trim Installation:
Insert one leg of each "L" bracket into the top
and side trim piece. Align the trim to form a
precise corner, then tighten the two set
screws with a small standard screwdriver.
Slide the trim over the panels. Place the
spring clips behind the panels at the locations
shown. This keeps the trim tight against the
panel.
Micro (1/16”)
Standard
Screwdriver
Spring
Clips
Optional Knock-Out
An optional knock-out is provided if the power cord is
routed behind the surround panel.
Install the top panel so
the tabs insert into the
joggle clips on the top
panel
b
  • Page 1 1
  • Page 2 2

Lopi 33 DVI Gas Fireplace Insert Operating instructions

Lopi
Brand
Lopi
Model
33 DVI Gas Fireplace Insert
Category
Fireplaces
Type
Operating instructions
This manual is also suitable for

Lopi 33 DVI Gas Fireplace Insert: Experience the warmth and ambiance of a traditional fireplace with the convenience of gas. Enjoy adjustable flame height, variable heat output, and remote control operation for effortless temperature management. Create a cozy atmosphere in any room with this versatile insert, designed to fit seamlessly into your existing fireplace. Its compact size and clean-face design make it a stylish addition to any home.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents