Datapath Aetria Network Manager Quick start guide
- Category
- Gateways/controllers
- Type
- Quick start guide
Engineering the world’s best visual solutions
Aetria Network Manager
Quick Start Guide
Thank you for purchasing the Aetria WallControl.
The aim of this document is to quickly guide you
through the process of initial setup.
For more detailed information, relevant User Guides
can be downloaded from www.datapath.co.uk.
2
Aetria Network Manager Quick Start Guide
GETTING STARTED WITH AETRIA NETWORK MANAGER
The Installation wizard will automatically
boot the Datapath Aetria Network Manager
option as highlighted above and continue
with the conguration of the Aetria
Network Manager:
Use the cursor keys and select ‘OK’ to
continue.The next step of the conguration
is to set the Hostname for the Aetria
Network Manager:
Enter the fully qualied domain name then
select ‘Yes’ and press Enter.A conrmation
dialog is then displayed, this should be
checked for errors.If there are any errors in
the hostname, select ‘No’ and re-enter the
hostname correctly.
1
2
3
3
Aetria Network Manager Quick Start Guide
Once satised the hostname is correct,
select ‘Yes’ and the Network Interface Card
(NIC) Assignment Menu is displayed
in the next dialog:
Select the required NIC(s) to assign them
for the Management network.Each server
appliance is normally supplied with two
NICs installed. The one not selected for
Management network will automatically
be assigned to the AV network.
Select the NIC for the management
network then select ‘OK’ and press Enter.
A conrmation dialog is then displayed.
This should be checked to ensure the
correct NIC(s) have been selected.
4
5
6
Conrm the NIC selection and select ‘Yes’
and the Management IP Addressdialog
is displayed:
4
Aetria Network Manager Quick Start Guide
Enter the IP Address of the Aetria
Network Manager and select ‘OK’ and
the Management Subnet Mask dialog
is displayed:
Enter the Management Subnet Mask and
select ‘OK’. The Management Gateway dialog
will then be displayed:
7
8
Enter the IP address of the Management
Gateway and select ‘OK’ and the Conrm IP
Details is displayed:
9
5
Aetria Network Manager Quick Start Guide
Check and conrm the IP Details.Select ‘Yes’
and the DNS Servers dialog is displayed:
Enter the IP address of the DNS Server.
Ensure the IP address is separated by a
space.Select‘OK’ and the ANM Setup
Menu is displayed:
Select ‘Initial Appliance Conguration’ and
then select ‘OK’.
Once the above steps are complete. Access
the Aetria Command Center using a Chrome,
Edge or Safari browser on a PC or laptop
connected to the Aetria network.
10
12
11
6
Aetria Network Manager Quick Start Guide
Datapath Ltd declares that this product complies with the essential
requirements and other relevant provisions of Directives 2014/30/EU,
2014/35/EU and 2011/65/EU.
A copy of our Declaration of conformity is available on request.
Datapath Limited
Bemrose House
Bemrose Park
Wayzgoose Drive
Derby, DE21 6XQ
UK
A full list of product compliance certications can be found in the product
User Guide on the Documentation Media supplied with the system.
CERTIFICATION
EU – Class A Declaration of Conformity
7
Aetria Network Manager Quick Start Guide
Datapath UK and
Corporate Headquarters
Bemrose House, Bemrose Park,
Wayzgoose Drive, Derby,
DE21 6XQ, United Kingdom
+44 (0) 1332 294 441
Datapath North America
2490 General q Avenue,
Suite 102, Norristown,
PA 19403, USA
+1 484 679 1553
www.datapath.co.uk
QSG-AET-EN2-V1.0
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
Datapath Aetria Network Manager Quick start guide
- Category
- Gateways/controllers
- Type
- Quick start guide
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Datapath Aetria Command Center Quick start guide
-
-
Datapath Aetria WallControl Quick start guide
-
-
-
-
-
-
-