Krone BA EasyFlow 300 S / 380 S Operating instructions

Original operating instructions

Grass header

EasyFlow 300 S

EasyFlow 380 S

(from serial no.: 1095268)

Order no.: 150 000 310 11 en-GB

Status: 04.08.2021

2

CV0

UKCA Declaration of Conformity

We

KRONE Agriculture SE

Heinrich-Krone-Str. 10, 48480 Spelle, Germany

hereby declare as manufacturer of the product named below, on our sole responsibility,

that the

Machine: Grass header

Type: EasyFlow 300 S, EasyFlow 380 S

to which this declaration refers is in compliance with the following relevant provisions of:

• Supply of Machinery (Safety) Regulations 2008, 2008 No. 1597

The signing Managing Director is authorised to compile the technical documents.

Spelle, August 04, 2021

Jan Horstmann

(Managing Director, Design & Development)

Year of manufacture:

Machine no.:

Importer and authorised representative:

Krone UK Ltd.

Phoenix Avenue

Micklefield, Leeds LS25 4D Y

Table of Contents

3

1 Table of Contents

1 Table of Contents ................................................................................................................................... 3

2 To this Document ................................................................................................................................... 6

2.1 Validity ................................................................................................................................................ 6

2.2 Re-Ordering ........................................................................................................................................ 6

2.3 Further applicable documents ............................................................................................................ 6

2.4 Target group of this document ........................................................................................................... 6

2.5 How to use this document .................................................................................................................. 7

2.5.1 Directories and References ........................................................................................................ 7

2.5.2 Direction Information ................................................................................................................... 7

2.5.3 Term “Machine” ........................................................................................................................... 7

2.5.4 Figures ........................................................................................................................................ 7

2.5.5 Scope of Document..................................................................................................................... 8

2.5.6 Means of representation ............................................................................................................. 8

2.5.7 Conversion table ....................................................................................................................... 11

3 Safety ..................................................................................................................................................... 13

3.1 Purpose of Use ................................................................................................................................. 13

3.2 Intended use ..................................................................................................................................... 13

3.3 Reasonably foreseeable misuse ...................................................................................................... 14

3.4 Service life of the machine ............................................................................................................... 14

3.5 Basic safety instructions ................................................................................................................... 15

3.5.1 Importance of the operating instructions ................................................................................... 15

3.5.2 Personnel qualification .............................................................................................................. 15

3.5.3 Personnel qualification of the technicians ................................................................................. 16

3.5.4 Children in danger ..................................................................................................................... 16

3.5.5 Connecting front attachments or trailers ................................................................................... 16

3.5.6 Structural changes to the machine ........................................................................................... 17

3.5.7 Additional equipment and spare parts ...................................................................................... 17

3.5.8 Workstations on the Machine .................................................................................................... 17

3.5.9 Operational safety: Technically perfect condition ..................................................................... 18

3.5.10 Danger zones ............................................................................................................................ 19

3.5.11 Keeping safety devices functional ............................................................................................. 21

3.5.12 Personal Protective Equipment ................................................................................................. 22

3.5.13 Safety sign on the machine ....................................................................................................... 22

3.5.14 Traffic safety .............................................................................................................................. 23

3.5.15 Parking the machine safely ....................................................................................................... 23

3.5.16 Consumables ............................................................................................................................ 24

3.5.17 Dangers associated with the operational environment ............................................................. 24

3.5.18 Sources of danger on the machine ........................................................................................... 25

3.5.19 Dangers associated with certain activities: Work on the machine ............................................ 26

3.5.20 Behaviour in hazardous situations and when accidents occur ................................................. 27

3.6 Safety routines ................................................................................................................................. 28

3.6.1 Shutting down and safeguarding the machine .......................................................................... 28

3.6.2 Supporting lifted machine and machine parts securely ............................................................ 28

3.6.3 Safely checking the oil level and changing the oil and filter element ........................................ 29

3.7 Location of the safety signs on the machine .................................................................................... 30

3.8 Location and meaning of the information signs on the machine ...................................................... 34

Table of Contents

4

3.8.1 Ordering additional warning signs and information signs ......................................................... 36

3.8.2 Attaching the safety signs and information signs ...................................................................... 36

3.8.3 Contact ...................................................................................................................................... 36

4 Machine Description ............................................................................................................................ 37

4.1 Machine overview ............................................................................................................................. 37

4.2 Overview of the different adaptation types ....................................................................................... 39

4.3 Identification Plate ............................................................................................................................ 40

4.3.1 Contact ...................................................................................................................................... 41

4.4 Overload protection .......................................................................................................................... 42

5 Technical data....................................................................................................................................... 43

5.1 Consumables ................................................................................................................................... 44

5.1.1 Oils ............................................................................................................................................ 44

5.1.2 Lubricating grease ..................................................................................................................... 44

6 Commissioning..................................................................................................................................... 45

6.1 Checks before starting up the machine for the first time .................................................................. 45

6.2 First installation ................................................................................................................................ 45

6.3 Converting infeed sheets to a width of 580 mm (BiG X 480–630 (up to YOM 19/20) and BiG X

series 201) .................................................................................................................................................... 46

6.4 Adjusting the machine to the forage harvesters BiG X 480–630 (up to YOM 19/20), and BiG X

series 201 and BiG X series 404 .................................................................................................................. 52

6.4.1 Adjusting the locking plates ...................................................................................................... 54

6.4.2 Adjusting the main angular gearbox ......................................................................................... 58

7 Start-up .................................................................................................................................................. 63

7.1 Check and observe before start-up .................................................................................................. 64

7.2 Mounting Machine on Forage Harvester .......................................................................................... 64

8 Driving and Transport .......................................................................................................................... 65

8.1 Preparing the machine for road travel .............................................................................................. 66

8.2 Switching off the machine ................................................................................................................ 67

8.3 Lashing the machine ........................................................................................................................ 68

8.4 Lifting the machine ........................................................................................................................... 69

9 Operation ............................................................................................................................................... 70

9.1 From transport into working position ................................................................................................ 70

9.1.1 Working position ........................................................................................................................ 70

9.2 Using the Machine for Work ............................................................................................................. 71

9.2.1 Reversing .................................................................................................................................. 71

9.3 Removing Machine from Forage Harvester ..................................................................................... 71

10 Settings ................................................................................................................................................. 72

10.1 Setting the Working Height .............................................................................................................. 72

10.1.1 Setting outer guide wheels ........................................................................................................ 72

10.1.2 Adjusting the central guide wheel ............................................................................................. 73

10.2 Roller crop guide .............................................................................................................................. 74

10.2.1 Height adjustment ..................................................................................................................... 74

10.2.2 Spring Relief Holding-Down Device .......................................................................................... 75

10.2.1 Position of Roller Crop Guide to the Holder Tine Tracks of the Pick-up ................................... 76

10.2.2 Setting the Lifting Speed of the Holding-Down Device ............................................................. 77

10.3 Adjusting swath guide plate ............................................................................................................. 78

10.4 Setting the conveyor sheets ............................................................................................................. 79

10.5 Setting the auger .............................................................................................................................. 81

Table of Contents

5

10.5.1 Adjusting the distance auger - auger trough ............................................................................. 81

10.5.2 Adjusting the distance between the scraper bars and the auger conveyor .............................. 82

11 Maintenance .......................................................................................................................................... 83

11.1 Special Safety Instructions ............................................................................................................... 84

11.2 Test run. ........................................................................................................................................... 84

11.3 Spare Parts ...................................................................................................................................... 84

11.4 Maintenance table ............................................................................................................................ 85

11.5 Tightening torques ............................................................................................................................ 87

11.5.1 Metric Thread Screws with Control Thread .............................................................................. 87

11.5.2 Metric Thread Screws with Fine Thread ................................................................................... 88

11.5.3 Metric Thread Screws with Countersunk Head and Hexagonal Socket ................................... 88

11.5.4 Tightening Torques for Locking Screws and Bleed Valves on the Gearboxes ........................ 89

11.6 Input gearbox ................................................................................................................................... 90

11.7 Spur wheel gearbox ......................................................................................................................... 91

11.8 Drive chains ...................................................................................................................................... 92

11.8.1 Drive chain of auger conveyor .................................................................................................. 93

11.8.2 Drive chain of receiver drum ..................................................................................................... 93

11.9 Changing the tines ........................................................................................................................... 94

11.10 Changing the conveyor sheets ......................................................................................................... 95

11.11 Guide wheels .................................................................................................................................... 95

11.12 Wear Sheets for Trough EasyFlow 300 S ........................................................................................ 96

11.13 Wear Sheets for Trough EasyFlow 380 S ........................................................................................ 96

11.14 Bleeding friction disc clutches .......................................................................................................... 97

11.14.1 Bleeding friction disc clutch on the tine rotor ............................................................................ 97

11.14.2 Bleeding friction disc clutch on the auger conveyor .................................................................. 99

11.15 Check hydraulic hoses ................................................................................................................... 100

12 Maintenance – lubrication ................................................................................................................. 101

12.1 Special Safety Instructions ............................................................................................................. 101

12.2 Lubrication Chart ............................................................................................................................ 102

13 Placing in Storage .............................................................................................................................. 104

14 Before the Start of the New Season ................................................................................................. 105

14.1 Special Safety Instructions ............................................................................................................. 105

14.2 Test run. ......................................................................................................................................... 105

15 Disposal of the machine .................................................................................................................... 106

15.1 Disposal of the machine ................................................................................................................. 106

16 Index .................................................................................................................................................... 107

To this Document

6

2 To this Document

2.1 Validity

These operating instructions apply to the grass headers of types:

EasyFlow 300 S

EasyFlow 380 S

2.2 Re-Ordering

You can request a replacement document if this document became completely or partly

unusable, or if you need it in a different language. Please specify the document number shown

on the cover page in your order. Contact data can be found in the chapter “Contact persons”.

The document can additionally be downloaded via KRONE MEDIA https://media.mykrone.green

.

2.3 Further applicable documents

To ensure that the machine is used safely and as intended, observe the following further

applicable documents:

– Operating instructions of universal shaft(s)

– Operating instructions of forage harvester, KRONE

2.4 Target group of this document

This document aims at the operators of the machine fulfilling the minimum requirements of

personnel qualification; refer to chapter entitled Safety “Personnel Qualification”.

To this Document

7

2.5 How to use this document

2.5.1 Directories and References

Table of contents/headers:

The table of contents as well as the headers in this instruction are used for quick navigation in

the chapters.

Index directory:

In the index directory, you can find information on the desired subject via catchwords which are

in alphabetical order. The index directory can be found on the last page of this instruction.

Cross references:

Cross references to another place in the operating instructions or to another document are in

the text and specify the chapter and subchapter or section. The designation of subchapters or

sections is presented in quotation marks.

Example:

Check that all screws on the machine are tight, refer to chapter Maintenance, “Tightening

Torques”.

The subchapter or the section can be found via an entry in the table of contents and in the index

directory.

2.5.2 Direction Information

Direction information in this document such as front, rear, right and left always applies in the

direction of travel.

2.5.3 Term “Machine”

In the rest of this document the grass header is also referred to as the "machine".

2.5.4 Figures

The figures in this document do not always represent the exact machine type. The information

which refers to the figure always corresponds to the machine type of this document.

To this Document

8

2.5.5 Scope of Document

In addition to standard equipment, accessories kits and versions of the machine are described

in this document. Your machine may deviate from this document.

2.5.6 Means of representation

Icons in the text

In this document, the following means of representation are used:

Action step

A bullet point (•) designates an action step you have to perform, as for example:

• Set the left outside mirror.

Sequence of actions

Several bullet points (•) located in front of a sequence of action steps identify a sequence of

actions to be performed step by step, as for example:

• Loosen counter nut.

• Set the screw.

• Tighten counter nut.

List

Dashes (-) identify lists such as, for example:

– Brakes

– Steering

– Lighting

To this Document

9

Symbols in figures

To visualize parts and actions steps, the following icons are used:

Icon

Explanation

1

Reference sign for part

I

Position of a part (e.g. move from pos. I to pos. II)

X

Dimensions (e.g. B = width, H = height, L = length)

Action step: Tighten screws with torque key with specified tightening torque

Direction of motion

Direction of travel

opened

closed

enlargement of display detail

Framings, dimension line, dimension line limitation, reference line for visible parts

or visible mounting material

Framings, dimension line, dimension line limitation, reference line for covered

parts or covered mounting material

Laying routes

LH

Left-hand machine side

RH

Right-hand machine side

To this Document

10

Warning signs

Warning

WARNING! - Type and source of hazard!

Effect: Injuries, serious material damage.

• Measures for hazard prevention.

Caution

CAUTION! - Type and source of hazard!

Effect: Damage to property.

• Measures for risk prevention.

Notes with information and recommendations

Note

Effect: Economic benefit of the machine.

• Measures to be performed.

To this Document

11

2.5.7 Conversion table

By means of the following table, metric units can be converted into US units.

Quantity

SI Units (Metric)

Factor

Inch-Pound Units

Unit Name

Abbreviation

Unit Name

Abbreviation

Area

hectare

ha

2.47105

acre

acres

Flow

liters per

minute

L/min

0.2642

US gallon per

minute

gpm

cubic meter

per hour

m³/h

4.4029

Force

newton

N

0.2248

pound-force

lbf

Length

millimeter

mm

0.03937

inch

in.

meter

m

3.2808

foot

ft.

Power

kilowatt

kW

1.3410

horsepower

hp

Pressure

kilopascal

kPa

0.1450

pound per

square inch

psi

megapascal

MPa

145.0377

bar (non-SI)

bar

14.5038

Torque

newton meter

Nm

0.7376

pound-foot or

foot-pound

ft∙lbf

8.8507

pound-inch or

inch-pound

in∙lbf

Temperature

degree

Celsius

°C

°Cx1.8+32

degree

Fahrenheit

°F

Velocity

meter per

minute

m/min

3.2808

foot per

minute

ft/min

meter per

second

m/s

3.2808

foot per

second

ft/s

kilometer per

hour

km/h

0.6215

miles per

hour

mph

Volume

liter

L

0.2642

US gallon

US gal.

milliliter

ml

0.0338

US ounce

US oz.

cubic

centimeter

cm³

0.0610

cubic inch

in³

Weight

kilogram

kg

2.2046

pound

lbs

To this Document

12

This page has been left blank deliberately.

Safety

13

3 Safety

3.1 Purpose of Use

The KRONE grass header EasyFlow 300 S and EasyFlow 380 S is used to take up mown

stalks and leaves. The crops are fed to the intake housing of a forage harvester.

Ver

3.2 Intended use

This machine is a pick-up and is used to collect crops and to feed them to the forage harvester.

The crops designated for the intended use of this machine are mown stalk and leaf crops.

The machine is designed exclusively for use in agriculture and may only be used when

– all safety devices are available according to the operating instructions and are in the

protective position.

– all safety instructions of the operating instructions have been observed and complied with,

both in chapter “Basic safety instructions” and directly in the chapters of the operating

instructions.

The machine may be used only by people who satisfy the personnel qualification requirements

designated by the machine manufacturer.

These operating instructions are part of the machine and must therefore be at hand when the

machine is in use. The machine may be operated only when the operator has received training

and in compliance with these operating instructions.

If the machine is used for applications which are not described in these operating instructions,

this may result in serious injuries or death and damage to the machine and other property.

Unauthorised modifications to the machine may affect the properties of the machine or disrupt

the proper operation. For this reason, unauthorised modifications shall exclude any liability of

the manufacturer for consequential damage.

The intended use shall also include the adherence to the operating, maintenance and repair

conditions set by the manufacturer.

Safety

14

3.3 Reasonably foreseeable misuse

Any use beyond the intended use, see chapter Safety, “Intended use”, is regarded as improper

use and is therefore misuse according to the Machinery Directive. The manufacturer is not liable

for damage resulting from this, the user alone bears the risk.

Such misuse is for example:

– Processing of crops which are outside the intended use of the machine, see chapter Safety,

“Intended use”

– Transportation of people

– Transportation of goods

– Exceedance of the permissible technical gross weight

– Non-compliance with the safety signs on the machine and safety notices in the operating

instructions

– Performing fault clearance, setting, cleaning, repair and maintenance work contrary to the

information in the operating instructions

– Unauthorised modifications to the machine

– Attachment of unauthorised or unapproved additional equipment

– Use of spare parts which are not KRONE original spare parts

– Stationary operation of the machine

Unauthorised modifications to the machine may affect the properties of the machine or disrupt proper

operation. For this reason, unauthorised modifications will release the manufacturer from any liability for

consequential damage.

3.4 Service life of the machine

– The service life of this machine strongly depends on proper use and maintenance as well as

the operating conditions.

– Permanent operational readiness as well as long service life of the machine can be

achieved by observing the instructions and notes of these operating instructions.

– After each season of use, the machine must be checked thoroughly for wear and other

damage.

– Damaged and worn parts must be replaced before placing the machine into service again.

– After the machine has been used for five years, carry out full technical inspection of the

machine. According to the results of this inspection, a decision concerning the possibility of

reuse of the machine should be taken.

Safety

15

3.5 Basic safety instructions

Non-compliance with the safety instructions and warnings

Non-compliance with the safety instructions and warnings may result in injuries and damage to

the environment and property.

3.5.1 Importance of the operating instructions

The operating instructions are an important document and a part of the machine. They are

aimed at the user and contain safety-relevant information.

Only the procedures indicated in the operating instructions are reliable. If the operating

instructions are not observed, people may be seriously injured or killed.

• Before using the machine for the first time, read and follow all the “Basic Safety Instructions”

in the Safety chapter.

• Before working, also read and observe the respective sections in the operating instructions.

• Keep the operating instructions ready to hand for the user of the machine.

• Hand over the operating instructions to subsequent users.

3.5.2 Personnel qualification

If the machine is not used properly, people may be seriously injured or killed. To avoid

accidents, each person who works with the machine must satisfy the following minimum

requirements:

– He is physically capable of controlling the machine.

– He can work safely with the machine in accordance with these operating instructions.

– He understands the method of operation of the machine within the scope of his work and

can identify and avoid the dangers associated with the work.

– He has read the operating instructions and can implement the information in the operating

instructions accordingly.

– He is familiar with driving vehicles safely.

– For road travel he has adequate knowledge of the highway code and has the stipulated

driving licence.

Safety

16

3.5.3 Personnel qualification of the technicians

If the work (assembly, conversion, modification, extension, repairs, retrofitting) is performed

improperly on the machine, people may be seriously or fatally injured. To avoid accidents,

everyone who performs work according to these instructions must meet the following minimum

requirements:

• Qualified professional, with relevant training.

• Capable of assembling the (partially) disassembled machine according to the assembly

instructions provided by the manufacturer.

• Capable of extending, modifying or repairing the function of the machine according to the

relevant instructions provided by the manufacturer.

• Ability to perform the work safely according to these instructions.

• Understands the mode of operation of the work to be performed and the machine and is

able to identify and avoid the hazards associated with the work.

• Has read these instructions and is able to apply the information in these instructions

accordingly.

3.5.4 Children in danger

Children cannot assess danger and behave unpredictably.

As a result, children are especially at risk.

• Keep children away from the machine.

• Keep children away from consumables.

• Especially before starting up and moving the machine, ensure that there are no children in

the danger zone.

3.5.5 Connecting front attachments or trailers

When the machine is connected incorrectly to a forage harvester, dangers are caused which

could lead to severe accidents.

• Observe all operating instructions when connecting:

– The operating instructions of the machine

– The operating instructions of the forage harvester

– The operating instructions of universal shaft

• Follow the coupling instructions, see chapter Initial Operation, “Adjusting the Machine to

Forage Harvester” and chapter Initial Operation “Attaching to the Forage Harvester”.

• Observe the changed driving behaviour of the combination.

Safety

17

3.5.6 Structural changes to the machine

Structural changes and enhancements may impair the functionality and operational safety of the

machine. Thus there is a risk of serious injuries or death.

Structural changes and enhancements are not permitted.

3.5.7 Additional equipment and spare parts

Additional equipment and spare parts which do not comply with the requirements of the

manufacturer may impair the operational safety of the machine and cause accidents.

• To ensure operational safety, use original parts or standard parts which correspond to the

requirements of the manufacturer.

3.5.8 Workstations on the Machine

Passengers

Passengers may be seriously injured by the machine or fall off the machine and get run over.

Ejected objects may strike and injure passengers.

• Never let people ride on the machine.

Safety

18

3.5.9 Operational safety: Technically perfect condition

Operation only when the machine has been started up correctly

If the machine is not started up correctly according to these operating instructions, the

operational safety of the machine is not ensured. As a result, accidents may occur and people

may be seriously injured or killed.

• Do not use the machine unless it has been started up correctly, see chapter Start-up.

Technically perfect condition of the machine

Improper maintenance and adjustment may affect the operational safety of the machine and

cause accidents. As a result, people may be seriously injured or killed.

• Perform all maintenance and adjustment work according to the chapters Maintenance and

Adjustment.

• Before performing any maintenance or adjustment work, shut down and safeguard the

machine, see chapter Safety "Shutting down and safeguarding the machine".

Danger resulting from damage to the machine

Damage to the machine may impair the operational safety of the machine and cause accidents.

As a result, people may be seriously injured or killed. The following parts of the machine are

particularly important for safety:

– Safety devices

– Connecting devices

– Hydraulic system

– Universal shafts

If there are doubts about the operational safety of the machine, for example due to leaking fuel,

visible damage or an unexpected change to the operational behaviour:

• Shut down and safeguard the machine, see chapter Safety, "Shutting down and

safeguarding the machine".

• Immediately eliminate potential causes of damage, for example heavy soiling, or tighten

slack screws.

• If possible, repair the damage according to these operating instructions.

• In the case of damage which may affect operational safety and cannot be repaired

according to these operating instructions: Have damage repaired by a qualified service

centre.

Technical limit values

If the technical limit values of the machine are not observed, the machine may be damaged. As

a result, accidents may occur and people may be seriously injured or killed. Observance of the

following technical limit values is particularly important for safety:

– Permitted operating pressure of the hydraulics

– Maximum drive speed

• Observe limit values, see chapter Description of machine, "Technical data".

Safety

19

3.5.10 Danger zones

When the machine is switched on, a danger zone may be created around this machine.

To avoid getting into the danger zone of the machine, maintain at least the safety distance.

If the safety distance is not followed, people may be seriously injured or killed.

• Do not switch on the drives and the engine until you are sure that no one has ignored the

safety distance.

• If people ignore the safety distance, switch off the drives.

• Stop the machine in the shunting operation and field mode.

The safety clearance is:

For machine in shunting operation and

field mode

In front of the machine

30 m

Behind the machine

5 m

Laterally to the machine

3 m

For machine switched on without driving motion

In front of the machine

3 m

Behind the machine

5 m

Laterally to the machine

3 m

The safety distances named here are minimum distances according to the intended use. These

safety distances must be increased depending on operating conditions and environmental

conditions, when required.

• Before performing any work in the danger zone of the machine: Shut down and safeguard

the machine, see chapter Safety, "Shutting down and safeguarding the machine". This also

applies to brief inspection work.

• Consider the information in all relevant operating instructions:

– The operating instructions of the machine

– The operating instructions of the universal shaft

– The operating instructions of the forage harvester

– The operating instructions of the transport wagon

Safety

20

Danger zone between precision forage harvester and header

People staying between precision forage harvester and header could be seriously hurt or killed

caused by precision forage harvester rolling away, carelessness or machine movements.

• Before working between precision forage harvester and header: Shut down and safeguard

the machine, see chapter Safety, “Shutting Down and Safeguarding the Machine”. This also

applies to brief inspection work.

• If the lifting unit has to be actuated, keep all people away from the range of movement of

the header.

Danger zone when drive is switched on

When the drive is switched on, there is a danger to life caused by rotating machine parts. There

must be nobody in the danger zone of the machine.

• Before starting the machine, direct all people out of the danger zone of the machine.

• If hazardous situations arise, switch off drives immediately and instruct people to leave the

danger zone.

Danger zone universal shaft

People may be caught, pulled in and seriously injured by the universal shaft.

• Observe operating instructions for the universal shaft.

• Ensure sufficient overlap of section tube and universal shaft guards.

• Allow the universal shaft locks to engage. There must be no areas of the locking device on

the PTO shaft fork which could cause catching or entrapment (e.g. by annular design,

protective collar around the locking pin).

• Attach chains to prevent the universal shaft guards from rotating with the shaft.

• Make sure that there is no one in the danger zone of PTO shaft and universal shaft.

• Make sure that the universal shaft guards are mounted and that they are fully functional.

• Switch off the PTO shaft when the angles between the universal shaft and the PTO shaft

are too large. The machine may be damaged. Parts may be hurled up and cause injury to

people.

Danger zone PTO shaft

People may be caught, pulled in and seriously injured by the PTO shaft and the driven

components.

Before switching on the PTO shaft:

• Make sure that all safety devices are fitted and in the protection position.

• Ensure that there is nobody in the danger zone of PTO shaft and universal shaft.

• Switch off the drives if they are not necessary.

Page is loading ...

Krone BA EasyFlow 300 S / 380 S Operating instructions

Krone BA EasyFlow 300 S / 380 S Operating instructions

Related papers

Other documents