NeuLog NUL-202 User guide

1

V2018.01 English

User Guide

NUL-202

Español

English

2

V2018.01 English

NeuLog logger sensors

and modules

Home

3

V2018.01 English

NeuLog logger sensors

Welcome to the new age of experimental data

acquisition with plug and play smart logger sensors.

NeuLog logger sensors offer a myriad of didactic tools to

meet your needs in the field of scientific studies.

The NeuLog system works as a set of independent

computer-based modules complete with a data logger,

flash memory and a sensor – all in each individual

sensor.

Sensors plug into each other and have the ability to

connect as a chain of sensors and then stream data to

any computer system or smart device.

The NeuLog system can connect to nearly any

computer platform or operating system (PC, MAC, iPad,

Tablets, Android, smart phones, etc). All that is needed is

a USB connection or wireless connectivity.

Note: NeuLog products are intended for educational

use.

Home

4

V2018.01 English

NeuLog user guide

This is a general guide for all NeuLog sensors and

modules instructing how to use them at various

operation modes. Specific user guides for each sensor

and module can be found at www.NeuLog.com. Choose

"Products" on the main menu, and then choose the

relevant sensor or module.

Each specific user guide contains the following sections:

 What is included with the sensor

 Sensor specifications

 Technical background

 Maintenance and storage

 Sensor offset (if needed)

Note: There are some sensors (listed below) that due to

their specific nature require different instructions than

the rest of the NeuLog sensors. For these sensors please

make sure to refer to www.NeuLog.com before use:

 NUL-209, Photo gate sensor

 NUL-243, GPS

Home

5

V2018.01 English

Quick start procedure

PC or Mac Computer – Wired Connection

Materials needed:

 NeuLog sensor or sensors

 USB-200 USB Module, or WIFI-201/WIFI-202 (using WiFi as

USB connection)

 USB to mini USB cable (included with the USB-200 module)

Your sensor needs to be connected to a USB-200

module. The USB-200 module then connects to a

computer via USB (this can also be done with WIFI-201

or WIFI-202). Please note that you cannot plug the

sensor directly into the computer.

The browser-based application can be downloaded for

free at www.NeuLog.com as well as a full application

user guide.

Choose "Downloads" on the main menu and then

choose "Software and Application".

Home

6

V2018.01 English

Procedure:

1. Install the NeuLog application.

2. Connect the USB-200 module to the PC or Mac.

3. Connect the sensor or sensors to the USB-200

module (they directly plug together). Please note that

no calibration is required for NeuLog sensors. You

should see the red LED on the sensor flash as you

plug them in.

4. Open the NeuLog application by clicking on the

shortcut on the screen.

5. The connected probes are automatically identified

by the software; including disconnecting or

connecting other probes.

6. Once a sensor module box appears on the left side of

the screen, the sensor will give a live reading in its

module box and on the graph appearing on the

screen and you can begin experimentation.

Home

7

V2018.01 English

7. Select one of the following function buttons and the

software will guide you through the function's

options:

a. 'Run Experiment' with the connected sensors.

b. 'Single Step' experiment.

c. 'Visual' display with four options for one of the

connected sensors values: Digital, Bar, Analog,

gauge and Accumulated graph.

d. 'Load Experiment' from the sensors' flash

memory.

e. 'Open Experiment' from a saved file.

f. 'Tools' for changing the software settings or

sensor ID.

Tablet, smart phone or any device with WIFI connectivity

Materials needed:

 NeuLog sensor or sensors

 WiFi Module (WIFI-201 or WIFI-202)

 Battery Module (BAT-200 or BAT-202)

Your sensor or sensors needs to be connected to a WiFi

module. The WiFi module will create a closed NeuLog

WiFi network which will stream the NeuLog data to the

device of your choosing. Once your device is wirelessly

connected to the NeuLog network, you can run

experiments and collect data through a browser of your

choosing.

Home

8

V2018.01 English

Procedure:

1. Connect the sensor or sensors directly to the left side

of a WiFi module (no wires required).

2. Connect a BAT-200 module to the right side of the

WiFi module or BAT-202 to its left side.

3. Although not required, we recommend plugging the

BAT-200 to an outlet using a USB to mini USB cord.

The WiFi module will run for 60-90 minutes

(depending on the sensor) without being plugged in.

4. The WiFi module can be directly powered using a

mini USB to USB cord and plugging it into your

computer or a wall charger. Please note that this

function is only available on WiFi modules with the

mini USB port.

5. For further WiFi module instructions or the WIFI-201

or WIFI-202 quick start guide please visit:

www.NeuLog.com. Choose "Products" on the main

menu, then choose "WiFi Communication module".

6. The WiFi module indicator lights will flash. Take no

action until the LED turns blue. This can take up to

one minute.

7. Take your tablet or smart phone, go to the WiFi

settings and select the NeuLog network

(NeuLog0184 for example) which matches the ID

found on the back of the WiFi module (0184 for this

example).

8. Give your device about 20 seconds to connect to the

WiFi module.

Home

9

V2018.01 English

9. Once the device is connected, go to your browser

and type the website wifi201.com into the URL bar,

then wait for 30-60 seconds.

10. The connected probes are automatically identified

by the software including disconnecting or

connecting other probes.

11. Once a sensor module box appears on the left side of

the screen, the sensor will give a live reading in its

module box and on the graph appearing on the

screen and you can begin experimentation.

12. If you are not the first one to connect to this WiFi unit,

enter viewer mode and view the screens of the user

master who was the first to connect.

13. If you are the first one to connect (the Master), you

can select one of the following function buttons and

the program will guide you through the function's

options:

a. 'Run Experiment' with the connected sensors.

b. 'Single Step' experiment.

c. 'Visual' display with four options for one of the

connected sensors values: Digital, Bar, Analog,

gauge and Accumulated graph.

d. 'Load Experiment' from the sensors' flash

memory.

e. 'Open Experiment' from a saved file.

f. 'Tools' for changing the program settings or

sensor ID.

Home

10

V2018.01 English

14. You can click on the 'Release Master' button in the

'Tools' options and all the connected viewers will

have a new 'Be Master' button. The first one to click

becomes the 'Master'.

15. The 'Tools' also includes a 'WiFi Options' button that

enables to connect the WiFi module as a client to the

WiFi network and to connect to the module through

this network. This option allows using the internet

while using the NeuLog sensors.

16. If you have a newer generation of WIFI-201 module

(with the USB icon on the cover) or a WIFI-202

module this can be used as a USB-200, meaning you

can tether the probes directly to the computer using

the WiFi module. To engage operation in this fashion,

press three times on the panel button. Repeating this

operation will return the module to WiFi mode.

Tablet, smart phone with Bluetooth connectivity

Materials needed:

 NeuLog sensor or sensors

 BLT-200 – Bluetooth Module (requires IOS 10 and up

for Apple devices and BLE (Bluetooth Low Energy) for

Androids devices)

Download the NeuLog app from the "App Store" or from

"Google Play".

Home

11

V2018.01 English

Procedure:

1. Connect the sensor or sensors directly to the right

side of the Bluetooth module (no wires required).

2. Turn the Bluetooth module ON by pressing the BLT-

200 button, the blue LED will flash.

3. Run the app. The app will search for the module and

connect automatically. After connecting, the blue

LED on the module will light constantly, and at the

app the Bluetooth sign (on the right top corner) will

turn green.

4. If the connection fails, press the gray Bluetooth sign

(on the right top corner) to refresh the connectivity.

5. If there is more than one Bluetooth module available,

the app will ask you to choose which module to

connect.

6. The connected sensors are automatically identified

by the software including disconnecting or

connecting other probes.

7. Once a sensor module box appears on the left side of

the screen, the sensor will give a live reading in its

module box and on the graph appearing on the

screen and you can begin experimentation.

Home

12

V2018.01 English

8. You can select one of the following function buttons

and the software will guide you through the

function's options:

a. 'Run Experiment' with the connected sensors.

b. 'Single Step' experiment.

c. 'Visual' display with four options for one of the

connected sensors values: Digital, Bar, Analog,

gauge and Accumulated graph.

d. 'Load Experiment' from the sensors' flash

memory.

e. 'Open Experiment' from a saved file.

f. 'Tools' for changing the program settings or

sensor ID.

Operation with NeuLog Graphic Display Module (viewer)

Materials needed:

 NeuLog sensor or sensors

 VIEW-101 Graphic Display Module

 BAT-200 or BAT-202 Battery Module

Home

13

V2018.01 English

Procedure:

1. Connect the sensor or sensors to the viewer.

2. Connect the BAT-200 or the BAT-202 to the viewer.

3. The VIEW-101 will automatically detect the sensor

and you will see it appear on the left side of the

screen.

4. Once the sensor appears it will be monitoring data in

real time.

5. To run an experiment and collect data, press the run

icon (little green person).

Off-line experiments

Off-line experiments are when you do not have a sensor

connected directly to a computer, tablet, smart phone,

or NeuLog viewer.

Materials needed:

 NeuLog sensor or sensors

 BAT-200 or BAT-202 Battery Module

Materials needed to configure your offline experiment:

 USB-200 Module, WiFi module (WIFI-201 or WIFI-202)

or VIEW-101 Module

 USB to mini USB cable (included with the USB-200

module).

Home

14

V2018.01 English

Procedure:

1. To determine the experiment settings, first connect

to your chosen device (PC, Mac, tablet, smart device)

and wait until the sensor search has ended.

2. Click on each sensor's module box, on the left side of

the screen, and set the experiment parameters

(Range, Duration, Rate and Trigger) for this sensor.

The setting parameters will be saved in the sensor's

flash memory.

3. Connect the sensor or sensors to a charged BAT-200

or BAT-202 module.

4. When ready to collect data, press the "Start/Stop"

button on the sensor. A red light will turn on for the

duration of the experiment.

5. After the experiment has concluded (the "Start/Stop"

button is pressed again or the data collection period

ends). Connect the sensor or sensors to your chosen

device (you can find full instructions in each device's

quick start procedure section).

6. Open the NeuLog application.

7. Click the 'Load experiment' icon.

8. Select which experimental data to upload (up to 5

experimental runs can be stored at one time on the

sensor).

Home

15

V2018.01 English

Operation with NeuLog Digital Display Module (viewer)

Materials needed:

 NeuLog sensor or sensors

 VIEW-200 Digital Display Module

 BAT-200 or BAT-202 Battery Module

Prior to data collection, it is recommended that you

configure your sensors' settings to your specific

experimental needs. Instructions for off-line experiments

configuration procedure can be found in the "Off-line

experiments" section in the previous page.

If you only use the VIEW-200 to take live readings without

collecting data it is not required to configure your

sensors' settings (unless, if needed, for changing the

sensors' range).

Home

16

V2018.01 English

Procedure:

1. Connect up to 5 NeuLog sensors of your choice

together and into the left side of your viewer.

2. Connect a charged battery module into the right side

of the viewer. The screen will automatically turn on.

3. The viewer will begin searching for sensors at this

time – the screen will read "Search… %". This process

should take roughly 25 seconds to complete.

Note: If no sensors are found, disconnect and

reconnect the battery module.

4. Once the sensors have been detected, you can

begin collecting data directly onto the internal

memory of each sensor. To do this you simply need

to press the "Start/Stop" button on the front of each

sensor you wish to collect data with.

5. You can change which sensor data is displayed on

the VIEW-200 by pressing the button on the front of

the module.

Home

17

V2018.01 English

NeuLog Current

Logger Sensor Guide

NUL-202

Home

18

V2018.01 English

NeuLog current logger sensor NUL-202

The NeuLog current sensor can be used for any science

experiment which utilizes current readings. It is used in

the fields of Physics, Electronics, Chemistry, Biology, etc.

The sensor comes pre-calibrated so you can start

experimentation right out of the box using this guide.

Among hundreds of possible experimental subjects that

can be studied with the NUL-202 sensor are: fuel cells,

electrical parallel circuits, electrical series circuits and

electronics.

The current sensor's measurement units are: Amperes

(A): Amperes are the SI base unit of electric current.

Home

19

V2018.01 English

Included with sensor

 NeuLog General Guide.

 Red (positive probe) and black (negative probe) wires

with 4 mm plugs connected directly to the sensor's

body.

Sensor’s specifications

Range and operation modes

±2500 mA

ADC resolution

15 bit

Accuracy

1%

Resolution

1 mA

Max sample rate (S/sec)

100,000

Experiment Duration: 50 milliseconds to 31 days.

Sensor’s features

 Fully digital data.

 Rugged plastic ergonomic case.

 4 mm plugs and ground plugs for easy connectivity

 Pushbutton switch for Start/Stop experiments in off

line mode.

 LED indicator of experiment status (blinks while

collecting data).

 Pre-calibrated sensing equipment.

Note: NeuLog products are intended for educational

use.

Home

20

V2018.01 English

Videos and experiment examples

 Videos, literature and other probes can be found at

www.neulog.com.

 In order to access the voltage sensor's page, choose

"Products" on the main menu and then "Current

logger sensor".

 In order to access the current sensor's experiments,

choose "Example Labs":

Ohm's Law (P-10)

How Incandescent Light Bulbs Work? (P-11)

Basic Electromagnetism (P-16)

Circuits and Series Resistance (P-24)

Current Variations and Generation of a Magnetic Field

(P-27)

Home

Page is loading ...

NeuLog NUL-202 User guide

NeuLog NUL-202 User guide

in other languages

Related papers

Other documents