D133 OPERATOR MODULE
TS400
MANUAL
Safety Instructions Page 2
Assembly Page 3
Connection Page 4
Operation Page 5
Technical data Page 5
Order overview Dimension Page 6
Schematic Page 7
www.aps-systems.ch
2
Safety Instructions
For your own safety and for the operational safety of the device, please read the following
instructions before commissioning the TS400-D133 operator module.
Cleaning:
Do not use any liquid cleaners or corrosive agents but only a damp cloth.
Installation:
Installation may only be carried out by qualified personnel.
Please regard the maximum cable length for the ethernet or serial connection.
Observe the maximum supply voltage and the polarization. Too high supply voltage will
destroy the device.
Assembly:
The TS400-D133 operator module must not be mounted unprotected outdoors, in rooms
with high humidity or in contact with condensation water.
When installing on uneven surfaces, measures must be taken to restore dust tightness.
3
Assembly
The TS400-D133 operator module can be mounted on a wall bracket or monitor arm using a
100x100mm VESA mounting device. A mounting bracket is available for installation in
equipment or cabinet fronts.
Installation in fronts:
The installation bracket 832.700.494 (accessory) is required for installation in fronts.
The required front cut-out is 180x310mm.
The two brackets are attached to the op-
erator module with the M5x6mm screws.
The operator module is fixed in the front
with the M5x70mm screws.
Wall mounting:
For wall mounting, the wall bracket 832.700.490 (accessory) is required.
The bracket is attached to the operator
module with three M4x6mm screws.
The counterpart is fixed to the wall.
The operator module is inserted into the
holder from top to bottom and locked with
the locking screws.
4
Connection:
The TS400-D133 operator module is preferably connected to the TS400 CPU processor
module via LAN2 to the Technet. Alternatively, the connection can be established with a seri-
al null-modem cable. The power supply can either be provided by 24VDC on the screw con-
nector 1. or by a 12VDC desktop power supply on the connector 2.
1: Connection of supply voltage Screw-type plug-in terminal
Connection terminal for the 24VDC power supply.
2: Connection of supply voltage Desktop power supply unit
Connection socket for power supply with the 12V/4A desktop power supply units 832.700.495
or 832.400.496.
3: LAN connection
Network connector for connection to the TS400 CPU processor module. The bidirectional
network communication channel to the TS400 CPU must be ensured.
4: Serial connection
Serial port for connection to the TS400 CPU processor module. The use of the visualization
can be limited due to the data transfer rate.
The other connections not described are not used.
5
Operation:
After switching on the supply voltage, the power switch must be pressed and the TS400-
D133 operator module switches on. The last status is stored and restored after an interrup-
tion of the supply voltage. No further user intervention is therefore necessary during nominal
operation.
After the boot process the Linux user login appears. You do not need to log in here; the
TS400-D133 operator module is integrated and parameterized in the configuration interface
of the TS400.
Operation of the TS400 user interface is described in the TS400 manual.
Technical data:
Dimensions
336.4 x 214 x 30.8mm (WxHxD)
Dimensions for front cutout
310 x 180mm
Height for front mounting
7mm
Screen size
13.3" / diagonal 337.82mm
Screen resolution
1920 x 1080 pixels
Brightness
≥ 300cd/m2
Temperature range
0 to +60°C
Humidity
0 to 90%
Degree of protection
IP20
Power consumption
12W
Supply voltage Connection 1
24VDC (12-28VDC)
Supply voltage Connection 2
12VDC with desktop power supply
Weight
2.0kg
Assembly
VESA mount 100mm or front mounting
6
Order overview:
TS400-D133
TS400 Operator module
832.700.490
TS400-D133 Wall bracket fixed
832.700.491
TS400-D133 Wall bracket swivel-mounted
832.700.494
TS400-D133 Front mounting bracket
832.700.495
TS400-D133 Desktop power supply 12V/4A CH cable
832.700.496
TS400-D133 Desktop power supply 12V/4A EU cable
Dimensions:
7
Schematic:
8
01.20
APS systems AG
Neumatt 4
CH-4626 Low buchites 41 (0)62 517 88 33
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Other documents
-
Xantrex TS400 User manual
-
General Monitors TA502A Single Channel Trip Amplifier Module Owner's manual
-
-
-
OPTI-UPS TS1000C User manual
-
Optoma Technology TS400 User manual
-
Baldor TS25 Installation guide
-
SEWOO SLK-TS400 User manual
-
Bull System Backup / Restore User guide
-
V7 VPL1075-1E Datasheet
