Dakota Digital VHX-70D-STD Mounting Manual

Dakota Digital
Brand
Dakota Digital
Model
VHX-70D-STD
Type
Mounting Manual

Dakota Digital VHX-70D-STD

Dakota Digital VHX-70D-STD is an instrument cluster designed to replace the stock gauge cluster in 1970-74 Dodge/Plymouth E-Body Non-Rallye vehicles. It features a digital display with various customizable options, allowing users to tailor the cluster to their preferences and needs. The VHX-70D-STD comes with a universal sender pack, enabling compatibility with various sensors for monitoring parameters such as speed, fuel level, and engine temperature.

Dakota Digital VHX-70D-STD

Dakota Digital VHX-70D-STD is an instrument cluster designed to replace the stock gauge cluster in 1970-74 Dodge/Plymouth E-Body Non-Rallye vehicles. It features a digital display with various customizable options, allowing users to tailor the cluster to their preferences and needs. The VHX-70D-STD comes with a universal sender pack, enabling compatibility with various sensors for monitoring parameters such as speed, fuel level, and engine temperature.

Manual # 650672
VHX-70D-STD
Dakota Digital VHX Instrument Installation
For 1970-74 Dodge/Plymouth E-Body Non-Rallye
Your new VHX-70D-STD kit includes:
Installation
Installation Manuals
Control Box
36” CAT5 Cable
Universal Sender Pack
VHX Display
1. Remove the stock plastic bezel from the dash. Retain all factory hardware for reassembly.
(3) Indicator
Harnesses
Switch Assembly
Manual # 650672
2. Remove the stock gauge cluster by removing the four (4) screws; retain hardware for
reassembly.
3. Mount the VHX system to the dash by reusing the four (4) screws that held the factory cluster.
Manual # 650672
face flush to the front of the bezel or a bezel that has a step where the indicators are recessed from
the front of the bezel. If you have the stepped bezel you will need to remove the three (3) indicator
light guides by removing the two (2) small phillip screws on each light guide. Re-install the gauge
bezel to the dash using the factory hardware and refer to the main manual for wiring instructions to
complete the VHX installation.
4A. This system comes with two options for the turn signals and brake indicator. You can have the
indicators located in the faceplate of your new VHX display, and/or indicators in the stock locations.
To use the new faceplate indicators, follow the wiring instructions found in the main VHX manual.
To optionally use the stock locations, do not connect the signal wires to the VHX control box.
Instead, use the two provided two-wire harnesses. The harnesses plug directly into the connectors
on the back side of your new VHX system:
WHITE\GREEN wire to INDICATOR CIRCUIT
WHITE\BLACK wire to CHASSIS GROUND
4B. Attach the provided CAT5 cable to
the back of the VHX system and
carefully route the open end to the
control box mounting location.
Indicators are flush
Indicators are stepped
Indicator light guides remain
Indicator light guides are removed
Manual # 650672
WARNING: This product can expose you to chemicals including lead, which is known to the State of
California to cause cancer and birth defects or other reproductive harm. For more information go to
www.P65Warnings.ca.gov
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Dakota Digital VHX-70D-STD Mounting Manual

Dakota Digital
Brand
Dakota Digital
Model
VHX-70D-STD
Type
Mounting Manual

Dakota Digital VHX-70D-STD

Dakota Digital VHX-70D-STD is an instrument cluster designed to replace the stock gauge cluster in 1970-74 Dodge/Plymouth E-Body Non-Rallye vehicles. It features a digital display with various customizable options, allowing users to tailor the cluster to their preferences and needs. The VHX-70D-STD comes with a universal sender pack, enabling compatibility with various sensors for monitoring parameters such as speed, fuel level, and engine temperature.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers