One Holland, Irvine, California 92618, U.S.A. Phone: +1-949-951-5003
Industrieweg 24, 8071 CT Nunspeet, The Netherlands Phone: +31-341-272222
3-77 Oimatsu-cho, Sakai-ku, Sakai-shi, Osaka 590-8577, Japan
* Service Instructions in further languages are available at: http://si.shimano.com
Please note: Specifications are subject to change for improvement without notice. (English)
© Apr. 2014 by Shimano Inc. HTR
SI-0129A-001-00
General Safety Information
WARNING
If the laser beam gets into your eyes, it may cause blindness.
•
Do not look at the laser beam directly.
•
Do not let the laser beam get into your eyes while using the product, regardless of
whether the laser beam is seen directly or through mirrors.
•
Do not control or adjust the product in any way other than by following the
procedures provided in this manual. It may cause you to be exposed to hazardous
laser beam emissions.
•
This is a class A product. In a domestic environment this product may cause radio
interference in which case the user may be required to take adequate measures.
Note:
This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at his
own expense.
Service Instruction
SI-0129A-001
BF-XY01
XY Position Tool
Names of parts
A warning label and an
explanatory label
Certification label and
Identifi cation label
Y-axis moving rail
Position Tool
Laser radiation section
X-axis moving rail
Operation and indication screen
Basic usage
Inserting the batteries
Move the position tool to the uppermost section of the Y-axis moving rail. While pressing
in the marked section of the back cover, slide the back cover upwards to remove it. Insert
two AA batteries in the order shown in the fi gure then put the back cover back.
Two AA batteries
Turning on the screen display
Holding down any position on the position tool screen for one second or longer turns the
screen on.
Turning off the screen display
Turns the display of the position tool screen off.
Measurement
1.
First, press [laser ON / OFF] on the
position tool to turn on laser emissions.
OFF ON
2.
Then, set the laser pointer at the
reference point. Slide the rail to move
the position tool and set the pointer at
the cross at the center of the crank.
Reference point
3.
With the pointer placed over the
intersection point of the cross, press
the X reset button and Y reset button
to set the reference point to zero.
4.
Move the position tool to the
measuring point and measure the
position. Press at any position you want
to save in order to save the
measurement value. Values of three
positions can be saved.
Handle position
207 179
207 179
207
E
179
Other position
Displaying settings and information
Change settings
The change settings screen appears. Change the set values using [-] or [+] on the
left or right of each item. Holding down the button continuously switches the
display, and holding down the button longer switches the display quickly.
SETTINGS
Language
English
Display brightness
100 %
Power saver
5 min
Power-off display
10 min
Power-off sensors
PMB-10 01-01 .02
60 min
1.
2.
3.
4.
5.
6.
1.
Language setting
The language can be selected from three
languages.
English ↔ German ↔ Dutch
2.
Display brightness adjustment
Adjust the brightness of the display.
Adjustment range: 0 % to 100 %
3.
Power saver setting
Set the time until laser emissions are turned
off.
Adjustment range: 1 min to 5 min
4.
Power-off display setting
Set the time until the screen display is turned
off when a stand-by state has continued for a
long time.
Adjustment range: 1 min to 10 min
5.
Power-off setting
Set the time until the system is powered off
when a stand-by state has continued for a
long time.
Adjustment range: 10 min to 60 min
6.
Return to the previous screen.
Display information
Information such as the basic functions of the XY position tool and its usage
appears.
Laser specifi cations
Maximum power 1 mW
Wavelength 650 nm
Beam divergence 1.1 mrad
Reset button
Pressing the inside of the
frame resets the position
coordinate to 0.
Coordinate display
Shows the current coordinate.
Saving measurement value
Measurement values of the
X-axis and the Y-axis at each
position can be saved as the
measurement values for the
section selected by pressing.
Turning the laser ON / OFF
The laser turns on or off
with each press.
Turning off the screen display
Display information
Change settings
0
207
179
0
207 179
207
E
179
Saddle position
1
Leica TPS1200+ Series User manual
Topcon DS-105AC User manual
Roland LV-290 User manual
Sokkia CX-107 User manual
Hilti POS15/18 Operating instructions
CAB cabLase Operating instructions
Konica Minolta VIVID 300 User manual