DRAKE DAR8642 Quick Manual

Brand: DRAKE

Model: DAR8642

Category: Video line amplifiers

Type: Quick Manual

This manual is also suitable for

Rack Mount Distribution Amplifiers, with Power Doubled Hybrid Output 1

DESCRIPTION

The R.L. DRAKE models DAR8642, DAR8633, DAR8618,

DAR7542, and DAR7533, are broadband distribution

amplifiers designed for indoor headend use in both

residential and commercial buildings where RF signal

distribution in the frequency range of 54 to 860 MHz is

required. Each model, except the DAR8618, incorporates a

push-pull hybrid input preamp and a power doubled hybrid

output amplifier to provide a very low distortion signal for

launch amp applications in the output of an SMATV or CATV

headend. The Gain and Slope controls both have a range of

10 dB minimum and operate between the preamp hybrid

and the output hybrid to maintain a low noise figure over a

wide range of gain and slope settings. Only the DAR8618

has a power doubled output hybrid with no input preamp and

no adjustable gain and slope controls. All models have a

provision for optional fixed input attenuators and equalizers.

Double-sided, plated through hole, glass epoxy, printed

circuit boards, and SMT are used for low losses and

maximum reliability.

All DAR models include a built-in diplexer filter. This allows

the return path energy that is present at the output port of

the DAR to be separated from the DAR output and passed

to the return path output port.

Input and output test connectors are provided for convenient

monitoring of the signal path. The amplifier circuitry is

designed for maximum stability, low distortion, low noise

figure, and is protected in a rugged aluminum housing.

- The unit operates from a nominal 115 VAC, 60 Hz input.

- Input equalizer and fixed attenuator options are available.

GAIN SLOPE

DAR DISTRIBUTION AMPLIFIER

INPUT MONITOR

-30 dB

POWER

OUTPUT MONITOR

-30 dB

MIN. MAX.

MIN. FLAT

F1 - POWER LED

This indicator illuminates when power is supplied to the unit.

F2 - INPUT MONITOR

This connector may be used to monitor input to the DAR.

The levels will be 30 dB below the input levels at R3.

F3 - GAIN*

Adjusts the amplifier interstage attenuator.

F4 - SLOPE*

Adjusts the slope of the output signal.

F5 - OUTPUT MONITOR

This connector may be used to monitor the output of the

DAR. Levels will be 30 dB below those present at R2.

R2 must be terminated in 75 Ohms for an accurate reading.

Not present on models with gain below 20 dB.

F1 F2 F3 F4 F5

2 Rear Panel Connections

FUSE

RETURN PATH

OUTPUT

RF OUTPUT

RF INPUT

FUSE

1/2 A , 250 V SLO - BLO

115 VAC , 60 Hz

40 WATTS

R1 - RETURN PATH OUTPUT

Any return path signals from 5 to 42 MHz that are present at

R2 will be passed to this port.

R2 - RF OUTPUT

This is the RF output for CATV distribution and is the

amplified output of channels that are input to port R3 from

54 MHz and higher. At this port, any return path channels

from 5 to 42 MHz will be passed at unity gain to port R1.

R3 - RF INPUT

This connector accepts the RF input from a headend

combiner output, 54 MHz and higher.

R4 - FUSE

If necessary, replace this fuse only with a fuse of the same

indicated rating.

R5 - AC LINE CORD

Connect this line cord to a 115 V / 60 Hz AC power source.

R1 R2 R3 R4 R5

Installation 3

INSTALLATION

1) Unpack the distribution amplifier.

2) Mount the amplifier in the desired location in the rack. Be

sure to leave at least one open rack space above and below

the amp to allow proper ventillation.

3) Connect input and output cables to the amplifier.

4) Plug the power line cord into a 115 VAC/60 Hz power

source.

5) Preset slope control fully clockwise.

6) While monitoring the output levels at the Output Monitor

-30 dB test port, adjust the Gain control for desired output at

the high end of the band. Then monitor the lowest channel

and adjust slope control to equalize this channel to the

desired level (usually equal to but not higher than the high

end of the band). Since there can be a slight interaction

between the slope and gain settings, it is advised to repeat

this step a few times to ensure the desired levels are

attained.

NOTE: The -30 dB input and output test ports can be used

to monitor input and output levels. These are only accurate

when the load is connected to the amplifier output and

power is on.

A WORD CONCERNING INPUT LEVELS

It is important to keep the input level to the amplifier within

an optimum range. If the level is too high, higher nonlinear

distortion will result and if the level becomes too low, C/N

might be less than desired. As a general rule, stay within

the optimum input level range listed in the specifications.

The listed levels assume a fully loaded channel complement.

Higher levels may be used if the channel loading is less.

In general, install a fixed input attenuator if required to set

the highest frequency channels in the input to within the

optimum range. Then set the amplifier gain to achieve the

desired output level, not to exceed the maximum output level

listed in the specifications. Then, if the low frequency

channels are above the optimum input level range, a fixed

input equalizer can be installed to drop the low frequency

channels to within this range. Use the slope control to make

fine adjustments.

FIXED INPUT ATTENUATOR

LOCATION

A factory installed jumper is

installed here for no

attenuation. To install an

input attenuator, remove

jumper and plug in a "SXP"

type attenuator rated for the

same or higher frequency as

the amplifier.

OUT

INSTALLING FORWARD PATH INPUT ATTENUATOR

Remove top cover as described below. If input levels are

enough to cause a high distortion level in the input amplifier,

a fixed input attenuator may be added. Choose an SXP type

attenuator of the value required, and install at the location

indicated below. Remove the 0 dB wire jumper to allow

insertion of the attenuator.

INSTALLING AN INPUT EQUALIZER

Follow the same basic procedure as described above for the

input attenuator except that the equalizer is installed at the

equalizer location shown below:

RF INPUT OF REAR PANEL

GROUND

INPUT EQUALIZER

LOCATION

A factory installed jumper is

installed here for no

equalization. Install desired

"QSA" type equalizer here. If

equalizer is not used, the

jumper must be connected

between the IN and OUT

connections.

IN OUT

GROUND

4 Specifications and Warranty

Forward Gain Adjustment Range:

Slope Control Adjustment (54 MHz):

Input/Output Impedances:

Input and Output Monitor Ports:

Fixed Input Attenuator:

Fixed Input Equalizer:

Hum Modulation:

Frequency Coverage (return port):

RF Shielding:

10 dB minimum (except DAR8618).

75 Ohms.

- 30 dB.

Plug-in (SXP type) available.

Plug-in (QSA type) available.

- 70 dB.

5 to 42 MHz.

Leakage complies with FCC Part 76.

Frequency Coverage (forward path):

Forward Gain:

Noise Figure:

Return Loss, Input & Output:

Channel Loading:

Output Level (maximum per channel

for distortions listed below):

Input Level (maximum without using

fixed input attenuator):

Optimum Input Level Range

for Best Performance:

Nonlinear Distortions-

Composite Triple Beat:

Composite Second Order:

Cross-modulation:

DAR7533

54 to 750 MHz.

33 dB.

7 dB maximum.

14 dB.

110 CH.

+44 dBmV.

+20 dBmV.

+10 dBmV to

+15 dBmV.

- 58 dB.

- 60 dB.

DAR7542

54 to 750 MHz.

42 dB.

6.5 dB maximum.

14 dB.

110 CH.

+44 dBmV.

+10 dBmV.

+0 dBmV to

+5 dBmV.

- 58 dB.

- 60 dB.

R.L. DRAKE COMPANY

230 INDUSTRIAL DRIVE

FRANKLIN, OHIO 45005 U.S.A.

CUSTOMER SERVICE AND PARTS TELEPHONE: +1 (937) 746-6990

TELEFAX: +1 (937) 743-4576

WORLD WIDE WEB SITE: http://www.rldrake.com

Power Requirement:

Operating

Temperature Range:

Size:

Weight:

Models DAR7533, 7542, 8633, 8642 -

115 VAC, 60 Hz, 24 Watts;

Model DAR8618 -

115 VAC, 60 Hz, 18 Watts.

- 20 deg. to + 60 deg. C.

19.00" (48.3 cm) W x 7.5" (19.1 cm) D

x 1.75" (4.5 cm) H.

6 lbs. 4 oz. (2.9 Kg).

DAR8633

54 to 860 MHz.

33 dB.

7.5 dB maximum.

14 dB.

129 CH.

+40 dBmV.

+18 dBmV.

+7 dBmV to

+12 dBmV.

- 60 dB.

- 64 dB.

DAR8642

54 to 860 MHz.

42 dB.

7 dB maximum.

14 dB.

129 CH.

+40 dBmV.

+7 dBmV.

-3 dBmV to

+2 dBmV.

- 60 dB.

- 64 dB.

THREE YEAR LIMITED WARRANTYTHREE YEAR LIMITED WARRANTY

THREE YEAR LIMITED WARRANTY

R.L. DRAKE COMPANY warrants to the original purchaser this product shall be free from defects in material or workmanship for three (3) years from

the date of original purchase. During the warranty period the R.L. DRAKE COMPANY or an authorized Drake service facility will provide, free of charge,

both parts and labor necessary to correct defects in material and workmanship. At its option, R.L. DRAKE COMPANY may replace a defective unit.

- To obtain such warranty service, the original purchaser must:

(1)(1)

(1) Retain invoice or original proof of purchase to establish the start of the warranty period.

(2)(2)

(2) Notify the R.L. DRAKE COMPANY or the nearest authorized service facility, as soon as possible after discovery of a possible defect, of:

(a) the model and serial number,

(b) the identity of the seller and the approximate date of purchase; and

(c) A detailed description of the problem, including details on the electrical connection to associated equipment and the list of such equipment.

(3)(3)

(3) Deliver the product to the R.L. DRAKE COMPANY or the nearest authorized service facility, or ship the same in its original container or equivalent,

fully insured and shipping charges prepaid.

- Correct maintenance, repair, and use are necessary to obtain proper performance from this product. Therefore carefully read the

Instruction Manual. This warranty does not apply to any defect that R.L. DRAKE COMPANY determines is due to:

(1)(1)

(1) Improper maintenance or repair, including the installation of parts or accessories that do not conform to the quality and specifications of the original

parts.

(2)(2)

(2) Misuse, abuse, neglect or improper installation.

(3)(3)

(3) Accidental or intentional damage.

- All implied warranties, if any, including warranties of merchantability and fitness for a particular purpose, terminate three (3) years from the date of

the original purchase.

- The foregoing constitutes R.L. DRAKE COMPANY’S entire obligation with respect to this product, and the original purchaser shall have no other

remedy and no claim for incidental or consequential damages, losses or expenses. Some states do not allow limitations on how long an implied warranty

lasts or do not allow the exclusions or limitation of incidental or consequential damages, so the above limitation and exclusion may not apply to you.

- This warranty gives you specific legal rights and you may also have other rights which vary from state to state. This warranty shall be construed under

the laws of Ohio.

ADDITIONAL SPECIFICATIONS FOR SPECIFIC MODELS

SPECIFICATIONS COMMON TO ALL MODELS (unless otherwise noted)

DAR8618

54 to 860 MHz.

18 dB.

7.5 dB maximum.

14 dB.

129 CH.

+40 dBmV.

+22 dBmV.

N/A