Panasonic PT-DW7000 User manual

Panasonic
Brand
Panasonic
Model
PT-DW7000
Category
Data projectors
Type
User manual
< 1 >
S PEC F ILE
Product Number : PT-DW7000
Product Name : 3-Chip DLP™ Projector
As of February 2009. Appearance and specifications are subject to change without notice.
S PEC F ILE
PT-DW7000
3-Chip DLP™ Projector
As of February 2009 < 2 >
Specifications
Main Unit
Power supply: North America:
Europe, Asia
Power consumption:
DLP™ chip: Panel size:
Display method:
Pixels:
Lens:
Lamp:
Screen size:
Brightness*
1
:
Center-to-corner uniformity *
1
:
Contrast*
1
:
Resolution:
Scanning frequency: RGB:
YPBPR (YCBCR):
S-Video/Video:
Optical axis shift*: Vertical:
Horizontal:
Keystone correction range:
Installation:
Terminals: RGB1 IN:
R, G, B:
Y, P B, PR
RGB2 IN:
R, G, B:
Y, P B, PR
120 V AC, 20 A, 60 Hz
220–240 V AC, 15 A, 50/60 Hz
800 W (800 VA)(North America: 12 W in standby mode with fan
stopped, Europe: 15 W in standby mode with fan stopped)
0.85˝ diagonal (16:9 aspect ratio)
DLP™ device x 3 (R, G, B), DLP™ projection system
1,049,088 (1,366 x 768) x 3, total of 3,147,264 pixels
Optional powered zoom/focus lenses
300 W UHM lamp x 2
70– 600 inches, 16:9 aspect ratio
(70 – 300 inches with the ET-D75LE5, 16:9 aspect ratio)
6,000 lumens (four-lamp operation mode)
90%
4,000:1 (full on/full off, in dynamic iris 3 mode)
1,300:1 (full on/full off, with dynamic iris off)
1,366 x 768 pixels (Input signals that exceed this resolution will be
converted to 1,366 x 768 pixels.)
Horizontal: 15–100 kHz, Vertical: 24– 120 Hz*
2
,
Dot clock: 20–162 MHz
480i: fH 15.75 kHz; fV 60 Hz, 576i: fH 15.63 kHz; fV 50 Hz,
480p: fH 31.50 kHz; fV 60 Hz, 576p: fH 31.25 kHz; fV 50 Hz,
720/60p: fH 45.00 kHz; fV 60 Hz, 1035/60i: fH 33.75 kHz; fV 60 Hz,
1080/60i: fH 33.75 kHz; fV 60 Hz, 1080/50i: fH 28.13 kHz; fV 50 Hz,
1080/25p: fH 28.13 kHz; fV 25 Hz, 1080/24p: fH 27.00 kHz; fV 24 Hz,
1080/24sF: fH 27.00 kHz; fV 48 Hz,
1080/30p: fH 33.75 kHz; fV 30 Hz
Horizontal: 15.75/15.63 kHz, Vertical: 50/60 Hz,
(NTSC, NTSC4.43, PAL, PAL60, PAL-N, PAL-M, SECAM)
±70% (±60% with the ET-D75LE6) from center of screen, powered
±30% from center of screen, powered
Vertical: ±40° (±34° with the ET-D75LE1, ±19° with the ET-D75LE5,
±28° wih the ET-D75LE6)
Ceiling/floor, front/rear
BNC x 5
G: 0.7 Vp-p (1.0 Vp-p for sync on G), 75 ohms,
B, R: 0.7 Vp-p, 75 ohms
HD, VD, SYNC: 1.4–5.0 Vp-p, positive/negative automatic
Y: 1.0 p-p, 75 ohms (incl. sync signal), PB/PR: 0.7 Vp-p, 75 ohms
0.7 Vp-p (1.0 Vp-p for sync on G), 75 ohms
D-sub HD 15-pin (female) x 1
G: 0.7 Vp-p (1.0 Vp-p for sync on G), 75 ohms,
B, R: 0.7 Vp-p, 75 ohms
HD, VD, SYNC: TTL, positive/negative automatic
Y: 1.0 p-p, 75 ohms (incl. sync signal), PB/PR: 0.7 Vp-p, 75 ohms
0.7 Vp-p (1.0 Vp-p for sync on G), 75 ohms
S PEC F ILE
PT-DW7000
3-Chip DLP™ Projector
As of February 2009 < 3 >
VIDEO IN:
VIDEO OUT:
S-VIDEO IN:
SERIAL IN*
4
:
SERIAL OUT*
4
:
REMOTE 1 IN:
REMOTE 1 OUT:
REMOTE 2 IN:
Optional board slot*
5
:
With ET-MD77SD1 installed: SERIAL IN:
SERIAL OUT:
LAN:
With ET-MD77SD3 installed: SERIAL IN:
SERIAL OUT:
LAN:
With ET-MD77DV installed: DVI-D IN:
With ET-MD77NT installed: LAN:
Power cord:
Cabinet material:
Dimensions (W x H x D):
Weight:
Operating temperature*
6
:
Operating humidity:
Remote Control Unit
Number of functions:
Power supply:
Operation range*
7
:
Dimensions (W x H x D):
Weight:
BNC x 1, 1.0 Vp-p, 75 ohms
BNC x 1, 1.0 Vp-p, 75 ohms, active through
Mini DIN 4-pin x 1
Y: 1.0 Vp-p, C: 0.286 Vp-p, 75 ohms
D-sub 9-pin (female) x 2, for external control (RS-232C/RS-422 compli-
ant)
D-sub 9-pin (male) x 1, for link control
M3 jack x 1 for wired remote control
M3 jack x 1 for link control
D-sub 9-pin (female) x 1 for external control (parallel)
x 1
BNC x 1, SD-SDI signal (4:2:2), SMPTE 259M compliant, 480i, 576i
BNC x 1, active through
RJ-45 x 1, for network connection, 10Base-T/100Base-TX
BNC x 1
SD-SDI signal (4:2:2): SMPTE 259M compliant, 480i, 576i
Single-link HD-SDI signal (YPBPR 4:2:2 10-bit): SMPTE 292M compiant,
720/50p, 720/60p, 1080/50i, 1080/60i, 1080/25p, 1080/24p,
1080/24sF, 1080/30p
BNC x 1, active through
RJ-45 x 1, for network connection, 10Base-T/100Base-TX
DVI-D 24-pin x 1, DVI 1.0 compliant, compatible with HDCP, compati-
ble with single link only
EDID1: 480p, 576p, 720/60p, 720/50p, 1080/60i, 1080/50i, 1080/24p,
1080/24sF, 1080/25p, 1080/30p
EDID2: Compatible with non-interlaced signals only,
Effective resolution: VGA (640 x 480) – U-XGA (1,600 x 1,200),
Dot clock: 25–162 MHz
RJ-45 x 1, for network connection, 10Base-T/100Base-TX
2.5 m/8´2˝
Moulded plastic
530 x 200 x 569 mm (20-7/8˝ x 7-7/8˝ x 22-13/32˝) (without lens)
22 kg (48.5 lbs) or less (without lens)
0°–40°C (32°–104°F)
10%–80% (no condensation)
32 keys, 46 functions
3 V DC (AA battery x 2)
Wireless: Approx. 7 m/23´ when operated from directly signal receptor
Wired: Approx. 15 m/49´3˝
50 x 31 x 181 mm (1-31/32˝ x 1-7/32˝ x 7-1/8˝)
110 g (3.9 oz) (including batteries)
S PEC F ILE
PT-DW7000
3-Chip DLP™ Projector
As of February 2009 < 4 >
Weights and dimensions shown are approximate. Specifications subject to change without notice.
*1 Values indicate overall average values of the product at the time of shipment and are stated based on JIS X 6911:2003 Data Projector
Specification Sheet Format. Measurement method and conditions are based on Appendix 2.
*2 Smooth image reproduction may not be possible when a motion video signal with a vertical frequency other than 50 or 60 Hz is input.
*3 Shift range is limited during simultaneous horizontal and vertical shifting.
*4 Contact your dealers for details when the control using RS-232C or RS-422 is required.
*5 The LAN terminal on the optional board will be inactivated after installation. Use the LAN terminal on the main unit.
*6 Operating temperature is 0°C– 40°C (32°F–104°F) when the fan control is set to “HIGHLAND” (for over 1,400 m to 2,700 m above sea level).
*7 Operation range differs depending on environments.
Supplied Accessories
Optional Accessories
Zoom lens (1.0–1.2:1):
Zoom lens (1.5–2.0:1):
Zoom lens (2.1–3.1:1):
Zoom lens (3.1–5.2:1):
Zoom lens (5.2–8.2:1):
Zoom lens (8.2–15.4:1):
Fixed-focus lens (0.8:1):
SD-SDI board:
HD/SD-SDI board:
DVI-D board:
Network board:
Wireless mouse receiver
Replacement lamp unit
Replacement long-life lamp unit
Ceiling mount bracket for high ceilings
Ceiling mount bracket for low ceilings
Dual stacking mount bracket
Carrying handle
Power cord, wireless/wired remote control, AA batteries for remote
control (x 2), remote control cable (15 m/49´3˝)
ET-D75LE6
ET-D75LE1
ET-D75LE2
ET-D75LE3
ET-D75LE4
ET-D75LE8
ET-D75LE5
ET-MD77SD1
ET-MD77SD3
ET-MD77DV
ET-MD77NT
ET-RMRC2
ET-LAD7700 (one bulb)
ET-LAD7700W (a set of two bulbs)
ET-LAD7700L (one bulb)
ET-LAD7700LW (a set of two bulbs)
ET-PKD77H
ET-PKD75S
ET-DFD75
ET-HAD75
S PEC F ILE
PT-DW7000
3-Chip DLP™ Projector
As of February 2009 < 5 >
Terminals
530 (20-7/8˝)
125 (4-15/16˝) 191 (7-1/2˝) 264 (10-3/8˝)
34 (1-5/16˝) 34 (1-5/16˝)
32 (1-1/4˝)
462 (18-3/16˝)
468 (18-7/16˝)
ø40 (ø1-9/16˝)
290 (8-1/4˝)
569 (22/3/8˝)
540 (21-1/4˝)
29
(1-1/8˝)
200 (7-7/8˝)
170 (6-11/16˝)
111 (4-3/8˝)44
(1-3/4˝)
97 (3-13/16˝)6 (1/4˝)
2 (1/16˝)
unit : mm (inch)
NOTE: This illustration is not drawn to scale.
1 Remote 1 input/output
2 Remote 2 input
3 Serial input/output
4 S-Video input
5 Video input/output
6 RGB 1 input
7 RGB 2 input
8 Optional board slot
Dimensions
12 3
45 6 78
S PEC F ILE
PT-DW7000
3-Chip DLP™ Projector
As of February 2009 < 6 >
Standard setting-up positions
Upper edge of projected image
Lower edge of projected image
Projected image
Projected image
L
ø60.5
340–420*54
344
(13-17/32˝)
(2-1/8˝)
440 (17-5/16˝)
(13-3/8˝–
16-17/32˝)*
271
345
(13-19/32˝)
271
100
(3-15/16˝)
298
* Adjustable in
40-mm step
(10-21/32˝) (11-23/32˝)
(ø2-3/8˝)
L
L
H
H
unit : mm (inch)
NOTE:
Illustrations show the projector installed
using optional ceiling bracket
ET-PKD75H and an optional lens
ET-D75LE1.
This illustration is not drawn to scale.
Projection distance (screen aspect ratio 16:9)
70
80
100
110
120
150
200
250
300
400
500
600
Lens
(Throw ratio)*
Screen
size
(inch,
diagonal)
ET-D75LE5
Fixed-focus
lens
(0.8:1)
Zoom lenses
except
ET-D75LE6
ET-D75LE6
Zoom lenses Fixed-
focus
lens
ET-D75LE1
Zoom lens
(1.5–2.0:1)
min. max.
ET-D75LE6
Zoom lens
(1.0–1.2:1)
min. max.
ET-D75LE2
Zoom lens
(2.1– 3.1:1)
min. max.
ET-D75LE3
Zoom lens
(3.1–5.2:1)
Zoom
Distance to screen Height from the
edge of screen to
center of lens (H)
Fixed-focus
min. max.
ET-D75LE4
Zoom lens
(5.2–8.2:1)
min. max.
ET-D75LE8
Zoom lens
(8.2–15.4:1)
min. max.
millimeters
*
The throw ratio is an approximate value calculated by dividing the screen width by the projection distance.
(Throw ratio) = (screen width) / (projection distance)
feet
3.8
4.4
4.9
5.5
6.7
8.4
11.3
14.2
17.1
-
-
-
–
–
–
–
–
–
–
–
–
–
–
–
-0.57
-0.65
-0.82
-0.90
-0.98
-1.23
-1.63
-2.04
-2.45
-3.27
-4.09
-4.90
3.43
3.92
4.90
5.39
5.88
7.35
9.80
12.26
14.71
19.61
24.51
29.41
–
–
–
–
–
–
–
–
–
–
–
–
-0.29
-0.33
-0.41
-0.45
-0.49
-0.61
-0.82
-1.02
-1.23
-1.63
-2.04
-2.45
3.15
3.60
4.49
4.94
5.39
6.74
8.99
11.23
13.48
17.98
22.47
26.96
1.43
1.63
1.84
2.04
2.45
3.06
4.09
5.11
6.13
-
-
-
7.7
8.8
9.9
11.0
13.3
16.7
22.3
27.9
33.5
44.8
56.0
67.2
10.1
11.6
13.1
14.6
17.6
22.1
29.7
37.2
44.7
59.7
74.7
89.7
5.2
5.9
7.4
8.2
9.0
11.2
15.0
18.8
22.6
30.2
37.8
45.3
6.1
7.0
8.8
9.7
10.6
13.3
17.9
22.4
27.0
36.1
45.2
54.2
10.3
11.9
13.4
14.9
17.9
22.4
29.9
37.5
45.0
60.1
75.2
90.3
15.5
17.7
20.0
22.3
26.8
33.6
44.9
56.2
67.5
90.1
112.7
135.3
15.6
17.8
20.1
22.3
26.9
33.7
45.0
56.3
67.6
90.2
112.8
135.4
26.0
29.8
33.5
37.3
44.9
56.2
75.1
94.0
112.9
150.6
188.4
226.2
26.1
29.9
33.7
37.4
45.0
56.3
75.2
94.1
113.0
150.8
188.5
226.3
40.7
46.7
52.7
58.8
70.8
88.8
118.8
148.9
178.9
239.0
299.0
359.1
40.8
46.8
52.8
58.9
70.9
88.9
118.9
149.0
179.0
239.1
299.1
359.2
77.5
88.8
100.1
111.3
133.8
167.6
223.9
280.1
336.4
448.9
561.5
674.0
1,151
1,328
1,681
1,857
2,033
2,563
3,445
4,327
5,209
-
-
-
–
–
–
–
–
–
–
–
–
–
–
–
-174
-199
-249
-274
-299
-374
-498
-623
-747
-996
-1,245
-1,494
1,046
1,195
1,494
1,644
1,793
2,241
2,989
3,736
4,483
5,977
7,472
8,966
–
–
–
–
–
–
–
–
–
–
–
–
-87
-100
-125
-137
-149
-187
-249
-311
-374
-498
-623
-747
959
1,096
1,370
1,507
1,644
2,055
2,740
3,424
4,109
5,479
6,849
8,219
436
498
561
685
747
934
1,245
1,557
1,867
-
-
-
2,322
2,664
3,349
3,692
4,035
5,062
6,775
8,488
10,201
13,626
17,052
20,477
3,103
3,561
4,476
4,934
5,392
6765
9,053
11,341
13,630
18,206
22,783
27,360
1,560
1,791
2,253
2,484
2,715
3,408
4,563
5,718
6,873
9,183
11,493
13,803
1,865
2,142
2,696
2,973
3,250
4,081
5,466
6,851
8,236
11,006
13,776
16,546
3,137
3,597
4,516
4,976
5,435
6,814
9,112
11,409
13,707
18,303
22,898
27,494
4,719
5,408
6,787
7,476
8,166
10,234
13,680
17,127
20,574
27,467
34,360
41,254
4,730
5,419
6,797
7,487
8,176
10,244
13,691
17,137
20,584
27,477
34,371
41,264
7,937
9,088
11,391
12,542
13,693
17,147
22,904
28,660
34,416
45,929
57,441
68,954
7,943
9,094
11,397
12,548
13,699
17,153
22,909
28,666
34,422
45,934
57,447
68,960
12,713
14,544
18,206
20,036
21,867
27,359
36,512
45,666
54,819
73,126
91,433
109,740
12,430
14,261
17,922
19,754
21,584
27,077
36,231
45,385
54,540
72,848
91,157
109,465
23,653
27,083
33,644
37,374
40,804
51,095
68,247
85,399
102,550
136,854
171,157
205,461
• The figures in the above table may vary by approximately ±5% depending on the projection lens that is used.
• When vertical keystone correction is used, the image is corrected in the direction that reduces its projected size.
• At the shortest projection distance, the zoom lens characteristics may cause slight image distortion.
• When the ET-D75LE6 is mounted, use the shade sheet supplied with the ET-D75LE6. The lens cover supplied with the projector cannot be
attached to the unit as it is.
S PEC F ILE
PT-DW7000
3-Chip DLP™ Projector
As of February 2009 < 7 >
ET-D75LE6
ET-D75LE1
ET-D75LE2
ET-D75LE3
ET-D75LE4
ET-D75LE8
ET-D75LE5
Calculation of the projection distance
For a screen size different from the above, use the equation below to calculate the projection distance.
Installable angle
Install the projector at an angle
within the range shown right.
• Vertical direction
The projector may be installed at
a vertical angle of 360 degrees.
Horizontal direction
The projector may be installed at
a horizontal angle of ±10 degrees.
Shift range
Optical axis shift function allows to shift the position of a projected image as shown below.
ET-D75LE1/D75LE2/D75LE3/D75LE4/D75LE8 ET-D75LE6
16 : 9 minimum L (mm) = (diagonal screen size in inches) x 23.10 – 57
maximum L (mm) = (diagonal screen size in inches) x 27.70 – 73
16 : 9 minimum L (mm) = (diagonal screen size in inches) x 34.26 – 76
maximum L (mm) = (diagonal screen size in inches) x 45.77 – 101
16 : 9 minimum L (mm) = (diagonal screen size in inches) x 45.96 – 80
maximum L (mm) = (diagonal screen size in inches) x 68.93 – 106
16 : 9 minimum L (mm) = (diagonal screen size in inches) x 68.93 – 96
maximum L (mm) = (diagonal screen size in inches) x 115.13 – 122
16 : 9 minimum L (mm) = (diagonal screen size in inches) x 115.13 – 116
maximum L (mm) = (diagonal screen size in inches) x 183.07 – 101
16 : 9 minimum L (mm) = (diagonal screen size in inches) x 183.09 – 386
maximum L (mm) = (diagonal screen size in inches) x 343.03 – 360
16 : 9 (fixed focus) L (mm) = (diagonal screen size in inches) x 17.64 – 84
• The figures in the above table may vary by approximately ±5% depending on the projection lens that is used.
• When vertical keystone correction is used, the image is corrected in the direction that reduces its projected size.
• At the shortest projection distance, the zoom lens characteristics may cause slight image distortion.
• When the ET-D75LE6 is mounted, use the shade sheet that is supplied with the ET-D75LE6. The lens cover that comes with the projector cannot
be attached to the unit as it is.
• Because the ETD75LE5 is a fixed short-throw lens, the lens shift function cannot be used with it.
Width of
projected image
(H)
Standard position
of
projected image
0.3H 0.3H
Heirght of
projected image
(V)
0.2V0.2V
0.2V
0.7V0.7V
0.2V
Width of
projected image
(H)
Standard position
of
projected image
0.2H 0.2H
Heirght of
projected image
(V)
0.2V0.2V
0.2V
0.6V0.6V
0.2V
S PEC F ILE
PT-DW7000
3-Chip DLP™ Projector
As of February 2009 < 8 >
List of compatible signals
This projector supports RGB signals with horizontal frequencies of 15 to 100 kHz, vertical frequencies
of 24 to 120 Hz and dot clock frequencies of 20 to 162 MHz.
NOTE: The native resolution of this projector is 1,366 x 768 pixels. If the display resolution of the input signal is different from the
native resolution, image compression or expansion will be used to convert the input signal to a level within the native resolution.
Display mode Display
resolution
(dots)
1
Scanning frequency
Horizontal
(kHz)
Vertical
(kHz)
720 x 480i
720 x 576i
720 x 480i
720 x 576i
720 x 483
720 x 576
1,920 x 1,080i
1,920 x 1,080i
1,920 x 1,080
1,920 x 1,080i
1,920 x 1,080
1,920 x 1,080
1,920 x 1,080
1,280 x 720
1,280 x 720
640 x 400
640 x 480
800 x 600
832 x 624
1,024 x 768
1,024 x 768i
1,152 x 864
1,120 x 750
1,120 x 750i
1,152 x 870
1,280 x 1,024
1,280 x 1,024i
1,400 x 1,050
1,600 x 1,200
15.7
15.6
15.73
15.62
31.57
31.25
33.75
28.13
27.00
27.00
28.10
33.75
33.75
45.00
37.50
24.80
31.50
31.47
35.00
37.86
37.50
43.27
32.10
35.16
37.88
48.08
46.88
53.64
49.73
48.36
56.48
60.02
65.50
68.68
80.70
94.00
35.52
64.00
67.50
77.10
50.10
32.60
68.68
52.35
63.98
78.20
79.98
91.15
46.20
47.60
65.20
78.80
82.20
75.00
59.9
50.0
59.9
50.0
59.9
50.0
60.0
50.0
24.0
24.0
25.0
30.0
59.9
60.0
50.0
56.4
70.1
59.9
66.7
72.8
75.0
85.0
51.0
56.3
60.3
72.2
75.0
85.1
74.6
60.0
70.1
75.0
81.6
85.0
100.8
120.0
87.0
70.0
74.9
85.0
60.1
80.0
75.1
50.0
60.0
71.7
75.0
85.0
86.0
89.9
60.0
72.0
75.0
60.0
NTSC/NTSC4.43/PAL-M/PAL60
PAL/PAL-N/SECAM
525i (480i)
625i (576i)
525p (480p)
625p (576p)
1125 (1080)/60i
1125 (1080)/50i
1125 (1080)/24p
1125 (1080)/24sF
1125 (1080)/25p
1125 (1080)/30p
1125 (1035)/60i
750 (720)/60p
750 (720)/50p
VGA400
VGA480
SVG A
MAC16
XGA
MXGA
MAC21
SXG A
SXG A+
UXGA60
1. The “i” appearing after the resolution indicates an interlaced signal.
Line flicker occurs when an interlaced signal is input.
S PEC F ILE
PT-DW7000
3-Chip DLP™ Projector
As of February 2009 < 9 >
Serial connector
The serial connector complies with RS-232C. To control the projector from a personal computer, com-
mands must be input through communication software, based on the format and satisfying the commu-
nication conditions shown below.
Basic format
Transmission from the computer begins with STX, then the ID, command, parameter, and ETX are sent
in this order. Add parameters according to the details of control.
Communication conditions (factory setting)
Pin assignments and signal names
D-sub 9-pin (female)
Serial input
Description
NC
Send data
Receive data
Connected internally
Ground
Signal name
–
TXD
RXD
–
GND
No.
1
2
3
4
5
Description
NC
Connected internally
Connected internally
NC
Signal name
–
CTS
RTS
–
No.
6
7
8
9
Pin assignments and signal names
D-sub 9-pin (male)
Serial output
Description
NC
Receive data
Send data
Connected internally
Ground
Signal name
–
RXD
TXD
–
GND
No.
1
2
3
4
5
Description
NC
Connected internally
Connected internally
NC
Signal name
–
RTS
CTS
–
No.
6
7
8
9
CAUTIION
• It may not be possible to send or receive commands for about 10 to 60 seconds when the lamp is first turned on. If this
occurs, wait for 60 seconds, then try sending or receiving again.
• When sending multiple commands, be sure to wait for at least 0.5 second after receiving a response from the projector before
sending the next command.
• Additional time is sometimes required for response due to processing inside the projector. Set the time-out period for com-
mand response to 10 seconds or more.
Start
(1 byte)
End
(1 byte)
Colon
(1 byte)
Semicolon
(1 byte)
ID designator:
01 to 64: Address number
0A to 0Z: Group ID
ZZ: All units (ID ALL)
ID 2 characters
(2 bytes)
Parameters
(undefined length)
Command
(3 bytes)
(Control and/or query commands)
STX ETXC1 P1 P2 ... PnC2A D I1 I2 C3 : ;
Signal level
Synchronization method
Baud rate
Parity
Character length
Stop bit
X parameter
S parameter
RS-232C-compliant
Start-stop synchronization
9,600 bps
None
8 bits
1 bit
None
None
S PEC F ILE
PT-DW7000
3-Chip DLP™ Projector
As of February 2009 < 10 >
Control commands
Command : Parameter Function Callback
PON
POF
IIS:RG1
IIS:RG2
IIS:VID
IIS:SVD
IIS:AUX
LPM:0
LPM:1
LPM:2
LPM:3
OSH:1
OSH:0
OPP:0
OPP:1
OPP:2
OPP:3
OAS
VPM:NAT
VPM:STD
VPM:DYN
VPM:CIN
VPM:GRA
OTE:0
OTE:1
OTE:2
OTE:4
OTE:9
OTE:10
TSD:y1y2y3y4m1m2d1d2w
TST:h1h2m1m2s1s2
OOS:1
OOS:0
Standby power on
Standby power off
RGB 1
RGB 2
Video
S-Video
AUX
Dual (two lamps)
Single lamp
Lamp 1
Lamp 2
Shutter on
Shutter off
P in P off
User 1
User 2
User 3
Natural
Standard
Dynamic
Cinema
Graphic
Low
Middle
High
User 1
User 2
Default
Date setting
Time setting
On-screen display on
On-screen display off
POWER (STANDBY)
INPUT SELECT
LAMP SELECT
SHUTTER
P IN P SELECT
AUTO SETUP
PICTURE MODE
COLOR TEMPERATURE
DATE
TIME
ON SCREEN
PON
POF
IIS:RG1
IIS:RG2
IIS:VID
IIS:SVD
IIS:AUX
LPM:0
LPM:1
LPM:2
LPM:3
OSH:1
OSH:0
OPP:0
OPP:1
OPP:2
OPP:3
OAS
VPM:NAT
VPM:STD
VPM:DYN
VPM:CIN
VPM:GRA
OTE:0
OTE:1
OTE:2
OTE:4
OTE:9
OTE:10
TSD:y1y2y3y4m1m2d1d2w
TST:h1h2m1m2s1s2
OOS:1
OOS:0
Cable specifications
1
2
3
4
5
6
7
8
9
1
2
3
4
5
6
7
8
9
PC (DTE)Projector
NC
NC
NC
NC
NC
NC
NC
NC
S PEC F ILE
PT-DW7000
3-Chip DLP™ Projector
As of February 2009 < 11 >
Status asking commands
Command:Parameter Function DescriptionCallback
QPW
QSH
QIN
QOS
QST
Q$L:1
Q$L:2
QSL
QIB
QPP
QGD
QGT
Main power status
Shutter function status
Input signal status
On-screen display status
Projector run time
Lamp 1 run time
Lamp 2 run time
Lamp operation mode status
Optional board slot status
P in P status
Date setting status
Time setting status
On
Off
On
Off
RGB 1
RGB 2
Video
S-Video
AUX
On
Off
00000h–99999h
0000h–9999h
0000h–9999h
Dual (two lamps)
Single lamp
Lamp 1
Lamp 2
ET-MD95SD1
ET-MD95SD3
ET-MD75DV
Uninstalled
Unknown
Not supported
Off
User 1
User 2
User 3
yyyymmdd (day of week)
(*1)
hhmmss
(*2)
001
000
1
0
RG1
RG2
VID
SVD
AUX
1
0
00000-99999
0000-9999
0000-9999
0
1
2
3
MD95SD1
MD95SD3
MD75DV
NONE
UNKNOWN
NOT SUPPORT
0
1
2
3
y1y2y3y4m1m2d1d2w
h1h2m1m2s1s2
*
1
*
2
Day of week: Monday = 1, Tuesday = 2, ... Sunday = 7
Set the date and time to UTC (universal time coordinated).
Command example
To set the on-screen display off, send the command as shown below.
ADZZ OOS : 0; ETX
ID Address
ZZ: ID ALL
Command
STX
Start
Character code 02
Parameter End
Character code 03
NOTE: When sending commands without parameters, a colon (:) is not necessary.
NOTE: If a wrong command is received, the projector will send an ER401 or ER402 command to the computer.
S PEC F ILE
PT-DW7000
3-Chip DLP™ Projector
As of February 2009 < 12 >
The projector uses a high-wattage lamp that becomes very hot during operation. Please observe the
following precautions.
1. Never place objects on top of the projector while it is operating.
2. Make sure there is an unobstructed space of 500 mm (19-11/16˝) or more around the projector’s
exhaust openings.
3. If the projector is placed in a box or enclosure, ensure the temperature of the air surrounding the
projector is between 0°C/32°F and 35°C/95°F. Also make sure the projector’s intake and exhaust
openings are not blocked. Take particular care to ensure that hot air from the exhaust openings is
not sucked into the intake openings.
500 mm (19-11/16˝)
or more
500 mm
(19-11/16˝)
or more*
500 mm
(19-11/16˝)
or more*
Operating the Projector Continuously
1. The lamp replacement cycle duration becomes shorter if the projector is operated continuously more
than 10 hours.
2. The lamp replacement cycle duration becomes shorter if the projector is operated repeatedly for short
periods.
Weights and dimensions shown are approximate. Specifications are subject to change without notice. This product may be subject to
export control regulations. DLP and the DLP logo are trademarks of Texas Instruments. All other trademarks are the property of their
respective trademark owners.
Direction of Air Intake and Exhaust
Notes on Projector Placement and Operation:
Intake
Exhaust
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12

Panasonic PT-DW7000 User manual

Panasonic
Brand
Panasonic
Model
PT-DW7000
Category
Data projectors
Type
User manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents