ESM301(L)-001 travel indication retrofit

MARK-10 ESM301(L)-001 travel indication retrofit User guide

  • Hello! I am an AI chatbot trained to assist you with the MARK-10 ESM301(L)-001 travel indication retrofit User guide. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
  • Where can I find the installation instructions for the MARK-10 ESM301(L)-001 travel indication retrofit?
    What tools do I need to complete the installation?
    How do I remove the sheet metal covers from the test stand?
    How do I remove the left side support plate?
    How do I remove the limit switch support plate?
    How do I position the linear encoder on the linear displacement strip?
    How do I install the linear travel displacement support plate?
    How do I install the encoder?
    How do I position the crosshead before re-installing the limit switch support plate?
    How do I re-install the limit switch support plate?
Mark-10 Corporation
11 Dixon Avenue, Copiague, NY 11726 USA
Tel: +1 631 842 9200
Fax: +1 631 842 9201
www.mark-10.com
We make a measurable difference in force and torque measurement
ESM301(L)-001 TRAVEL INDICATION OPTION
RETROFIT INSTALLATION INSTRUCTIONS
1. Loosen and remove the limit switch positioning screws, as shown below:
2.
Remove both sheet metal covers from the test stand by loosening the four screws on
each side, as shown below:
Mark-10 Corporation
11 Dixon Avenue, Copiague, NY 11726 USA
Tel: +1 631 842 9200
Fax: +1 631 842 9201
www.mark-10.com
We make a measurable difference in force and torque measurement
3. Remove the left side support plate by loosening the four Allen screws, as shown below:
4. Remove the limit switch support plate by loosening the four Allen screws, as shown
below:
Mark-10 Corporation
11 Dixon Avenue, Copiague, NY 11726 USA
Tel: +1 631 842 9200
Fax: +1 631 842 9201
www.mark-10.com
We make a measurable difference in force and torque measurement
5. Move the crosshead down to its lowest position on the test stand.
6. Position the test stand on its right side.
Mark-10 Corporation
11 Dixon Avenue, Copiague, NY 11726 USA
Tel: +1 631 842 9200
Fax: +1 631 842 9201
www.mark-10.com
We make a measurable difference in force and torque measurement
7. Note the three holes that are to be utilized for attaching the linear encoder.
8. Position the linear encoder on the linear displacement strip, at the end of the support
plate, as shown below:
Linear encoder
Displacement strip
Support plate
Mark-10 Corporation
11 Dixon Avenue, Copiague, NY 11726 USA
Tel: +1 631 842 9200
Fax: +1 631 842 9201
www.mark-10.com
We make a measurable difference in force and torque measurement
9. Place the linear travel displacement support plate onto the test stand, as shown in the
following images:
Mark-10 Corporation
11 Dixon Avenue, Copiague, NY 11726 USA
Tel: +1 631 842 9200
Fax: +1 631 842 9201
www.mark-10.com
We make a measurable difference in force and torque measurement
10. Install the linear travel displacement support plate with four Allen screws, as shown
below:
11. Install the encoder with the three supplied screws (two flat screws, one Phillips screw),
through the clearance holes in the support plate, as shown below:
Mark-10 Corporation
11 Dixon Avenue, Copiague, NY 11726 USA
Tel: +1 631 842 9200
Fax: +1 631 842 9201
www.mark-10.com
We make a measurable difference in force and torque measurement
12. Place the test stand upright and position the crosshead approximately 3 - 5 inches
(75 – 125 mm) above the base, as shown below:
3 – 5 inches
(75 – 125 mm)
13. Before re-installing the limit switch support plate, be sure to position the limit switches at
their furthest allowable extremes, as shown below:
Mark-10 Corporation
11 Dixon Avenue, Copiague, NY 11726 USA
Tel: +1 631 842 9200
Fax: +1 631 842 9201
www.mark-10.com
We make a measurable difference in force and torque measurement
14. Re-install the limit switch support plate.
15. Re-install the sheet metal covers.
Mark-10 Corporation
11 Dixon Avenue, Copiague, NY 11726 USA
Tel: +1 631 842 9200
Fax: +1 631 842 9201
www.mark-10.com
We make a measurable difference in force and torque measurement
16. Re-install the limit switch positioning screws.
17. Connect the coiled encoder cable between the mini-USB connector adjacent to the
linear encoder and the appropriate port in the rear of the test stand controller, as shown
below. ESM301(L)-001 installation is now complete.
/