Kohler 856-GH0-0 User manual

Installation and Care Guide

Bath with Airjets

Retain serial number for reference:

Numéro de série du produit:

Número de serie del producto:__________________________

Français, page “Français-1”

Español, página “Español-1”

1199249-2-A

Installation Instructions

WARNING: When using electrical products, basic precautions should always be followed,

including the following:

DANGER: Risk of electric shock. Connect only to a circuit protected by a Ground-Fault

Circuit-Interrupter (GFCI)*.

Building materials and wiring should be routed away from the blower body and other heat-producing

components of the unit.

Install to permit access for servicing.

A pressure wire connector marked ″Earth/Ground″ is provided within the wiring compartment. To reduce

the risk of electric shock, connect this connector to the grounding terminal of your electric service or supply

panel with copper wire equivalent in size to the circuit conductor supplying this equipment.

Pressure wire connectors are provided on the exterior of the junction box or control within this unit to permit

connection of a bonding conductor between this unit and all other exposed metal in the vicinity, as needed to

comply with local requirements.

An equipment grounding terminal is provided in the ﬁeld wiring compartment. To reduce the risk of electric

shock, this terminal must be connected to the grounding means provided in the electric supply panel with a

conductor equivalent in size to the circuit conductors supplying this equipment.

Grounding is required. The unit should be installed by a qualiﬁed service representative, and grounded.

WARNING: Risk of injury or property damage. Please read all instructions thoroughly before

beginning installation, including the following requirements.

WARNING: Risk of electric shock. A qualiﬁed electrician should make all electrical connections.

WARNING: Risk of electric shock. Disconnect power before servicing.

NOTICE: Follow all local plumbing and electrical codes. In Canada, install this unit in accordance with

the Canadian Electrical Code, Part 1.

*Outside North America, this device may be known as a Residual Current Device (RCD).

Product Information

Electrical Requirements

The installation must have a Class A Ground-Fault Circuit-Interrupter (GFCI) or Residual Current Device

(RCD). The GFCI or RCD protects against line-to-ground shock hazards. Use a 220 - 240 V, 20 A, 50/60 Hz

dedicated service for the bath.

Product Notices

WARNING: Risk of personal injury or property damage. Unauthorized modiﬁcation may cause

unsafe operation or affect performance of the bath. Do not relocate the blower motor, or make other

modiﬁcations to the bath system in the absence of kit or other published instructions, as this could

adversely affect the performance and safe operation of the product. Kohler Co. shall not be liable

under its warranty or otherwise for personal injury or damage caused by any such unauthorized

modiﬁcation. Refer to the ″Prepare the Blower (Remote Site)″ section for blower motor relocation

requirements, recommendations, and section coverage information.

NOTICE: Keep the area around the blower motor clean and free of debris. Ensure that the area around

the blower motor is free of sawdust, insulation, dirt, or other small loose debris. Such material could plug

the blower motor air intake and reduce the air ﬂow through the blower.

1199249-2-A 2 Kohler Co.

Product Information (cont.)

Features

Factory assembled components include a blower motor, air harness, control, check valve, butterﬂy valves,

chromatherapy lights (if provided), electrical harnesses, and an illuminated user keypad. Other than power

wiring and plumbing, no assembly is required.

Tools and Materials

Prepare the Blower (Remote Site)

NOTICE: The blower motor and the check valve must be relocated together. Do not relocate one

without the other.

NOTE: This bath can be installed as received or with the blower motor and check valve relocated to

another location. Refer to the appropriate sections throughout this manual for instructions related to your

particular installation. Read this section before relocating your blower.

Relocate the blower and check valve as close as possible to the bath to maximize performance. Do

not relocate the blower and check valve more than 15’ (4.5 m) from the bath.

•

Position the blower 1-1/2″ (38 mm) above the ﬂoor. Do not mount the blower motor with the

blower motor discharge pointing up.

•

Use 1-1/2″ PVC or equivalent rigid piping.

•

The piping installation must meet the requirements of local plumbing or building codes. Ensure that

the installation does not reduce the ﬁre rating of any walls. Piping must be supported at intervals

along the length in accordance with local codes.

•

Ensure that the blower motor location is clean and free of dust or debris.

•

Install an access panel for blower motor maintenance.

•

The 18 AWG minimum power cable to the blower motor must meet the requirements of all

applicable electrical or building codes. Ensure that the installation does not reduce the ﬁre rating of

any walls.

•

The power cord must be supported at intervals along its length in accordance with local codes.

Power cords must not rest on surfaces or ﬂoors that are subject to ﬂooding.

•

All material needed for the relocation must be supplied by the installer.

Additional tools and materials you will need:

Silicone Sealant

Plus:

• Conventional woodworking

tools and materials

• Drop cloth

• Metal shims

• 2x4s

Measuring Tape

Pencil Tin Snips

Safety Glasses

Level

Pipe Wrench

Kohler Co. 3 1199249-2-A

Prepare the Blower (Remote Site) (cont.)

•

Electrician pliers

•

Assorted screwdrivers

•

Adjustable wrench

•

Drill and bits to install the blower mounting fasteners

•

18 AWG non-metallic sheathed cable, two conductors with ground, with support clips, as required

•

One 4″ (102 mm) x 2″ (51 mm) electrical junction box with cover, gasket, and mounting screws

•

Three strain reliefs - one must ﬁt the blower motor cover with standard National Pipe Thread (NPT)

threads. The other two must ﬁt the holes in the new junction box.

•

Six wire connectors (wire nuts or equivalent)

•

1-1/2″ PVC or other rigid pipe with ﬁttings, unions, PVC cement (or equivalent fastening method),

and support clips, as required

•

Four fasteners (such as ﬂathead wood screws or concrete anchors) to secure the blower motor

•

Solid copper 8-gauge bonding wire, 36″ (914 mm)

1199249-2-A 4 Kohler Co.

1. Prepare the Site

WARNING: Risk of personal injury. This cast iron bath is extremely heavy. Obtain sufficient help

to carefully lift and move it.

NOTICE: Measure your product for site preparation. Note the model number located on the blower, then

visit the product page at www.kohler.com for more information.

NOTICE: Provide adequate ventilation and a minimum 15 cubic feet (.4 cubic meters) air space in the

installed location for cooling the motor and to supply sufficient air for the blower. Do not install the

blower motor closer than 1″ (25 mm) from the wall or other objects.

NOTICE: Provide generous, unrestricted access to the blower. You must provide access for servicing the

blower and controls. The access must be located immediately next to the blower.

NOTICE: Do not lift the bath by the piping or blower, or use the piping or blower for structural support

of the bath. To avoid damage to the bath, lift at the sides of the bath.

NOTICE: Do not support the weight of the bath by the rim.

NOTE: Drop-in, alcove, or corner installation is possible, depending on the product chosen.

Carefully unpack and inspect the new bath for damage before installation. If there is damage do not

install the bath; contact your dealer.

Make sure the ﬂooring offers adequate support for your bath, and verify that the subﬂoor is ﬂat and

level.

Construct 2x4 stud framing.

Install an access panel for future blower servicing. The access panel must be at least 34″ (864 mm)

wide by 15″ (381 mm) high.

Install the rough plumbing.

Install the drain to the bath according to the drain manufacturer’s instructions.

Protect the bath surface by positioning a clean drop cloth in the basin bottom.

Access

Panel

Construct according

to the product dimensions.

Construct 2x4

stud framing

according to the

roughing-in

information.

Position the

rough plumbing.

Verify that the subfloor

offers adequate support,

and is flat and level.

Alcove Drop-In

Position

the rough

plumbing.

Verify that the subfloor

offers adequate support,

and is flat and level.

Kohler Co. 5 1199249-2-A

2. Install the Bath

WARNING: Risk of personal injury. This cast iron bath is extremely heavy. Obtain sufficient help

to carefully lift and move it.

NOTICE: Do not lift the bath by the piping or blower, or use the piping or blower for structural support

of the bath. To avoid damage to the bath, lift by the rim at the sides of the bath.

Carefully move the bath into position.

Level the bath by ﬁtting metal shims under the feet as needed. Check for level along the rim. Make

sure the bath is resting on all four feet.

Cut the Banding Straps

IMPORTANT! This step is necessary to make the bath operate more quietly.

Cut the two banding straps from the blower.

Install the Plumbing

Insert the drain tailpiece into the trap. Secure the drain tailpiece to the trap.

Install the faucet valve.

Check the drain connections for leakage.

Level by fitting metal shims

under the feet.

Cut the banding

straps.

Control

Rubber

Isolation

Feet

Blower

Motor

1199249-2-A 6 Kohler Co.

3. Make Electrical Connections - Standard

NOTE: The product model number is printed on a label on the blower side of the bath. This label also

identiﬁes the electrical rating of the product. All baths come equipped with a wiring junction box and

are designed to operate between 220 V and 240 V at either 50 Hz or 60 Hz.

WARNING: Risk of electrical shock. Make sure the power has been disconnected before

performing the following procedures.

WARNING: Risk of electrical shock. Connect the blower to a properly grounded Ground-Fault

Circuit-Interrupter (GFCI) or Residual Current Device (RCD). This will provide additional

protection against line-to-ground shock hazard. A 220-240 V, 20 A, 50/60 Hz dedicated circuit is

required.

IMPORTANT! The load neutral is not used. There should be no connection to the load neutral terminal

on the Ground-Fault Circuit-Interrupter (GFCI) breaker. The green wire with the yellow stripe is the

equipment ground and needs to be connected to the neutral bus in the main circuit breaker box.

NOTE: The wiring harness includes an antenna for the optional remote control. Do not alter or damage

this antenna during installation.

Connect service to the junction box. The junction box contains blue, brown, and green with a yellow

stripe colored wires and a ground lug

Follow local electrical codes. Bond in accordance with national and local codes.

Control Power

Junction Box

Blue (L1)

Wire Connector

Ground

(Green with

Yellow Stripes)

From Control

Brown (L2)

Wire Connectors

Electrician to provide

suitable strain relief.

* Connections to be Made

at the Circuit Breaker

Typical Wiring Connection for North America

Control

Check Valve

Blower Motor Cord

Control

Power Supply

External Power

Field Wiring

(From Junction Box

to GFCI Breaker)

* Equipment Ground

* Line Neutral

(White

Curly Wire)

Neutral Bus

(In Breaker Box)

240 V

120 V

*L2

240 V

*L1

Typical Two-Pole

Circuit Breaker

with GFCI

Breaker Box

L2

L1

N

120/240 VAC Source

Bond in accordance with national and

local codes. Open bonding lugs are

located at the top of the junction box.

No Connection

(Load Neutral)

Kohler Co. 7 1199249-2-A

4. Disconnect the Blower Motor - Remote

NOTICE: This section applies only to installations in which the blower motor and check valve are

being relocated.

NOTICE: Do not cut the blower piping for this installation.

NOTICE: You must relocate the check valve with the blower motor. Do not disconnect the check valve

from the tee.

Remove the Blower Motor and Check Valve

Disconnect the blower motor electrical plug from the control.

Remove any cable ties that support the blower motor cord.

Remove and retain the screw holding the check valve to the PVC elbow.

Remove and retain the four screws from the baseboard.

Slide the blower motor and check valve away from the elbow, and remove the blower motor from

the bath.

Prepare the Site

NOTE: Refer to the ″Prepare the Blower (Remote Site)″ section for blower relocation details.

Prepare the site where the blower motor will be installed. The site must be within 15’ (4.5 m) of the

bath.

Install an access panel to service the blower motor.

Prepare the routing paths for the PVC piping and the new blower motor power cable. Follow all

applicable codes.

Elbow

Screw

Baseboard

Control

To Blower Motor

Cover

Blower Motor

Mounting Screws

Check

Valve

Blower Motor

Electrical Plug

Junction Box

1199249-2-A 8 Kohler Co.

5. Mount the Blower Motor and Check Valve - Remote

NOTE: The blower motor must be mounted horizontally 1-1/2″ (38 mm) above the ﬂoor. Do not mount

the blower motor with the discharge pointing up.

NOTE: Refer to the ″Prepare the Blower (Remote Site)″ section for other requirements for the blower

motor relocation.

At the new blower motor location, install a 1-1/2″ (38 mm) high block (not supplied) to support the

blower motor.

Use the blower motor as a template to mark the location of the four mounting bolts or screws.

Drill four 1/8″ (3 mm) pilot holes for the blower motor mounting screws.

Install and support PVC or other 1-1/2″ rigid piping (not supplied) between the blower motor

location and the air harness.

Connect the new piping to the existing air harness without modifying the air harness. Align the new

pipe and secure the connection with PVC cement. Allow the PVC cement to cure according to the

manufacturer’s instructions.

Connect the check valve assembly to the new piping. Align the new pipe with the check valve

assembly and drill a hole for the existing mounting screw. Use silicone or equivalent sealant at the

connections and reuse the screw that was removed previously. Allow the sealant to cure according

to the manufacturer’s recommendations.

Position the motor on the support block. Reinstall the screw on the check valve.

Fasten the blower motor to the new support block with the mounting screws.

Check Valve

Screw

Blower Motor

Mounting Screws

1-1/2" Rigid Piping

(not supplied)

1-1/2" (38 mm) Min

Kohler Co. 9 1199249-2-A

6. Terminate the Cable at the Blower - Remote

Route the Power Cable

Route 18 AWG or equivalent power cable (two conductors with ground) between the bath and

blower. Support and protect the cable. Follow local electrical codes.

Prepare the Blower for Remote Installation

Loosen the cable strain-relief nut on the blower motor. Push the nut back on the cable to provide

clearance for the cover removal.

Remove and retain the two access cover screws from the back of the blower motor. As you are

loosening the screws, check periodically if the cover can be slid back on the electrical cable.

When the cover is loose, use electrician pliers or equivalent to cut the electrical cable at a point

about 4” (102 mm) from where the cable enters into the blower motor housing.

Pull the free end of the electrical cord through the cover, insert, and strain relief nut.

Discard the existing strain relief nut and insert.

Reconnect the blower motor plug to the control.

Install a standard NPT threaded strain relief to the blower motor cover.

Connect the New Power Cable at the Blower Motor

On the 4″ (102 mm) pigtail lead of the blower motor, strip back the cable jacket about 3″ (76 mm).

On the customer-supplied power cable, strip back the cable jacket about 2″ (51 mm).

In the USA, mark white conductors with red or black tape as required by the National Electric Code

(NEC).

Strip the wire insulation 3/8″ (10 mm) from the blower motor pigtail and power cable leads.

Route the new power cable leads through the blower motor access cover and strain relief.

Using wire nuts or other approved termination methods, terminate the conductors as follows:

•

Connect the black pigtail lead to the L1 conductor of the power cable.

•

Connect the blue pigtail lead to the L2 or N conductor of the power cable.

•

Connect the green with yellow stripe pigtail lead to the power cable ground conductor.

With the two screws, reinstall the access cover on the blower motor.

Tighten the strain relief on the power cable at the blower motor.

Remove any dust or debris from the blower motor area.

Access Cover

Blower Motor

Plug

Remove screws, remove cover,

and cut existing cable about 4"

(102 mm) from the blower motor.

Strain Relief

1199249-2-A 10 Kohler Co.

7. Install the Blower Cord at the Control - Remote

Install the Second Junction Box on the Control

Install a second junction box with external bonding lug, two strain reliefs, and a cover (not

supplied) on the blower adapter board on the control.

Connect a solid copper 8-gauge bonding wire from the bonding lug on the new junction box to the

spare bonding lug on the control. Follow all local electrical codes.

Reconnect the Blower Motor Power Cord

If required, reconnect the blower motor power cord at the control.

Route the blower motor power cord through a strain relief on the second junction box. Tighten the

strain relief.

At the end of the cut power cord, strip back the cable jacket about 3″ (76 mm).

Using a wire nut, cap off the unused brown conductor in the cable jacket.

Strip about 3/8″ (10 mm) of wire insulation from the remaining control wires.

Reconnect the Blower New Power Cable

Route the customer-supplied power cable from the blower through the other strain relief on the

second junction box. Tighten the strain relief.

Strip back the cable jacket about 3″ (76 mm).

For installations in the USA, mark the white wire with either red or black electrical tape as required

by the National Electric Code (NEC).

Strip the end of the wires about 3/8″ (10 mm).

Use approved termination devices to terminate the conductors as follows:

•

Connect the black pigtail lead to the L1 conductor of the power cable.

•

Connect the blue pigtail lead to the L2 or N conductor of the power cable.

•

Connect the green with yellow stripe pigtail lead to the grounding or earthing conductor of the

power cable.

•

The brown wire is not used and should be capped with a wire nut.

Install the cover on the new junction box.

Wire Nut

Blue

Black

Brown

Strip back the jackets about

3" (76 mm) on the field cable

and on the blower motor pigtail.

Then cut the unused fourth

conductor brown wire off

at the point that the

cable jacket ends.

From Control50 Hz

60 Hz

L1

L2

L1

N

GND

NC

GND

NC

Green w/Yellow Stripe

Brown

Black

Blue

Ground (Green with

Yellow Stripe)

From Control

Cable to

Blower

Motor

New Field

Cable To

Blower Motor

Install junction box with cover

and bonding lug (not provided).

Route the cut end of the cord to

the new junction box. Add strain relief.

Blower Adapter

Board

Second

Junction Box

Blower

Motor Pigtail

Second Junction Box

Control Power Junction Box

Kohler Co. 11 1199249-2-A

8. Make Power Connections - Remote

WARNING: Risk of electric shock. To reduce the risk of electric shock, connect the control to a

properly grounded Ground-Fault Circuit-Interrupter (GFCI) or Residual Current Device (RCD). This

will provide additional protection against line-to-ground shock hazard. A dedicated 220-240 V, 20 A,

50/60 Hz circuit is required.

WARNING: Risk of electric shock. Make sure the power has been disconnected before performing

the following procedures.

Ensure that the control power supply cord is properly routed to the control power junction box. The

control power supply cord contains a brown wire (Line 1), a blue wire (Line 2), and a green wire

with a yellow stripe (ground or earth).

Install a strain relief (not provided) for the power supply cable to the control power junction box.

Route the power supply cable to the control power junction box.

As required, strip the jacket and wire insulation on both cables to make the connections.

For installations in the USA, mark any white conductor in the supply power wiring with red or

black tape as required by the NEC.

Connect service to the control power junction box.

Provide a separate equipment earthing or grounding conductor to the spare earth/ground lug

located on the control power junction box. This conductor must not be connected to any

current-carrying conductor. Follow local electrical codes.

Bond in accordance with national and local codes.

Clean the area of all dust and debris.

All wiring harnesses have been pre-wired at the factory. Ensure that all wires are securely fastened.

NOTE: Your wiring harness includes an antenna for the optional remote control. Do not alter or damage

this antenna during installation.

9. Complete the Installation

Test Run the Bath

Fill the bath to a level at least 4″ (102 mm) above the top of the highest airjet.

Operate the bath for 5 minutes and check all bath piping connections for leaks. Check for leakage

along the front, sides, and back of the bath.

For additional information on bath operation, see the ″Operating Instructions″ section.

Power Supply Cable

Blower Motor Cord

Control Power Supply

Control Power Junction Box

Second Junction Box

(added for Remote Blower)

Check Valve

New Field Cable To Blower Motor

Typical Remote Blower Installation

Remote Blower

1199249-2-A 12 Kohler Co.

Complete the Installation (cont.)

Finish the Installation

Install water-resistant wallboard and all ﬁnished wall, deck, and ﬂoor materials.

Apply silicone sealant to seal all areas where the bath and ﬁnished wall or deck meet.

Install the faucet trim.

Clean-up After Installation

When cleaning up after installation, do not use abrasive cleansers, as they may scratch and dull the

bath surface. Use warm water and a liquid detergent to clean the surface of the bath.

Remove stubborn stains or paint with turpentine or paint thinner. Do not allow cleaners containing

petroleum distillates to remain in contact with any bath surface for long periods of time. Remove

plaster by carefully scraping with a wood edge. Do not use metal scrapers, wire brushes, or other

metal tools. Use a powder-type detergent on a damp cloth to provide mild abrasive action to any

residual plaster.

Important Safety Instructions

READ AND FOLLOW ALL INSTRUCTIONS

SAVE THESE INSTRUCTIONS

INSTRUCTIONS PERTAINING TO A RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS

WARNING: When using electrical products, basic precautions should always be followed,

including the following:

DANGER: Risk of accidental injury or drowning. To reduce the risk of injury, do not permit

children to use this unit unless they are closely supervised at all times.

WARNING: Risk of personal injury. To avoid injury, exercise care when entering or exiting the

bath.

WARNING: Risk of electric shock. Do not permit electric appliances (such as a hair dryer, lamp,

telephone, radio, or television) within 5’ (1.5 m) of this bath.

WARNING: The use of alcohol, drugs, or medication can greatly increase the risk of fatal

hyperthermia. Prolonged immersion in hot water may induce hyperthermia. Hyperthermia occurs

when the internal temperature of the body reaches a level several degrees above the normal body

temperature of 98.6°F (37°C). The symptoms of hyperthermia include an increase in the internal

temperature of the body, dizziness, lethargy, drowsiness, and fainting. The effects of hyperthermia

include: (a) failure to perceive heat, (b) failure to recognize the need to exit the bath, (c)

unawareness of impending hazard, (d) fetal damage in pregnant women, (e) physical inability to

exit the bath, and (f) unconsciousness resulting in the danger of drowning.

WARNING: Risk of fetal injury. Pregnant or possibly pregnant women should consult a physician

before using the bath.

WARNING: Risk of hyperthermia or drowning. Do not use the bath immediately following

strenuous exercise.

WARNING: Risk of hyperthermia or drowning. Water temperature in excess of 100°F (38°C) may

cause injury. Test and adjust the water temperature before use.

Kohler Co. 13 1199249-2-A

Important Safety Instructions (cont.)

WARNING: Risk of personal injury. Never drop or insert any object into any opening.

Use this bath only for its intended purpose as described in this guide. Do not use attachments not

recommended by Kohler Co.

The bath must be connected only to a supply circuit that is protected by a Ground-Fault Circuit-Interrupter

(GFCI)*. Such a GFCI should be provided by the installer and should be tested on a routine basis. To test the

GFCI, press the test button. The GFCI should interrupt power. Press the reset button. Power should be

restored. If the GFCI fails to operate in this manner, the GFCI is defective. If the GFCI interrupts power to

the bath without the test button being pressed, a ground current is ﬂowing, indicating the possibility of an

electric shock. Do not use this bath. Disconnect the bath and have the problem corrected by a qualiﬁed

service representative before using.

Your new KOHLER bath has been listed by Underwriter’s Laboratories, ensuring safety for you and your

family. This bath also conforms to rigid ANSI and IAPMO standards set within the plumbing industry.

* Outside North America, this device may be known as a Residual Current Device (RCD).

1199249-2-A 14 Kohler Co.

Operating Instructions

NOTE: If the unit does not function properly, please refer to the “Troubleshooting” section.

Starting the Unit

Fill the bath to a level at least 4” (102 mm) above the top of the airjets.

Use your hand to test the water temperature for comfort and safety.

Carefully enter the bath basin.

Press the On/Off icon on the user keypad.

If desired, adjust the air ﬂow rate using the up or down buttons.

Selecting Air Flow Modes

Rotate the outer ring to select a desired mode.

Press the ″OK″ icon to activate the mode.

To turn off a mode, rotate the outer ring until the icon is ﬂashing green and then press the “OK”

icon again.

The icon will then turn blue, indicating the mode is off.

Stopping the Bath

When ready, press the On/Off icon a second time to stop the air system.

Carefully exit the bath.

When the bath drains below the level sensors an automatic, two-minute purge cycle occurs. The air

system then operates at low speed to blow any residual water out of the air harness.

Initiating a Manual Purge Cycle (when desired)

NOTE: Follow these steps if you choose to manually purge residual water from the air system.

After stopping the air system and draining the bath, rotate the ring on the user keypad to the

″Purge″ icon.

When the ″Purge″ icon is ﬂashing blue, press the ″OK″ icon once.

The ″Purge″ icon ﬂashes green and the manual purge mode begins. The air system operates at low

speed to blow any residual water out of the air harness.

After two minutes, the air system stops automatically.

Air Flow Mode

Activates Mode Selected

Power On/Off

Indicator Bar

Decrease Flow or Surge

Increase Flow or Surge

Zone 1

Zone 2

Zone 3

Surge Mode

Purge Mode

Chromatherapy Cycle (if provided)

Chromatherapy Specific

Color (if provided)

Rotate Outer Ring to

Access Desired Mode

Kohler Co. 15 1199249-2-A

Care and Cleaning

For best results, keep the following in mind when caring for your KOHLER bath with airjets:

•

Always test your cleaning solution on an inconspicuous area before applying to the entire surface.

•

Wipe surfaces clean and rinse completely with water immediately after applying cleaner. Rinse and

dry any overspray that lands on nearby surfaces.

•

Do not allow cleaners to soak on surfaces.

•

Use a soft, dampened sponge or cloth. Never use an abrasive material such as a brush or scouring

pad to clean surfaces.

•

The ideal cleaning technique is to rinse thoroughly and blot dry any water from the surface after

each use.

•

Use a soft nylon brush on slip-resistant surfaces. Be sure to use a water-soluble cleaner (dissolves

100% in water).

•

Do not use powdered cleaners unless the cleaner is fully dissolved in water. Solid substances can

block the airjets.

•

Do not use full strength bleach or ammonia cleaning solutions. Chemically active cleaning

solutions can damage the surface.

•

Do not use abrasive cleansers or solvents on airjet surfaces. Abrasive cleaners and solvents can

damage the airjet surface.

Maintaining the Airjets

If cleaning the airjets is necessary due to hard water deposits, wet a soft, non-abrasive cloth with

white vinegar and wipe the plugged airjet holes. Immediately rinse the area with clean water to

avoid long-term exposure of the vinegar to the airjet surface.

Fill the bath with water to the top row of airjets. Drain the bath and press the purge button.

Cleaning Your User Keypad and Remote Control

Use a soft cloth to wipe the keypad and remote control after each use. If the surface becomes dirty,

use a non-abrasive soap and warm water to clean.

For detailed cleaning information and products to consider, visit www.kohler.com/clean. To order Care &

Cleaning information, call 1-800-456-4537.

Warranty

Kohler Co. warrants the cast iron components of products manufactured after February 10, 2000, to be free of

defects in material and workmanship during normal residential use for as long as the original consumer

purchaser owns his or her home. Gloss reduction, scratching, staining and alkaline etching of the ﬁnish over

time due to use, cleaning practices or water or atmospheric conditions, are not manufacturing defects but are

indicative of normal wear and tear. This warranty applies only for KOHLER Cast Iron products installed in

the United States of America, Canada or Mexico (North America).

If a defect is found in normal residential use, Kohler Co. will, at its election, repair, replace or make

appropriate adjustment. Damage caused by accident, misuse, or abuse is not covered by this warranty.

Improper care and cleaning will void the warranty. Proof of purchase (original sales receipt) must be

provided to Kohler Co. with all warranty claims. Kohler Co. is not responsible for labor charges, installation,

or other incidental or consequential costs. In no event shall the liability of Kohler Co. exceed the purchase

price of the product.

If the cast iron product is used commercially or is installed outside of North America, Kohler Co. warrants

the cast iron product to be free from defects in material and workmanship for one (1) year from the date the

product is installed, with all other terms of this warranty applying except duration. All other components

other than the enameled cast iron carry Kohler Co.’s one-year limited warranty unless otherwise speciﬁed.

If you believe that you have a warranty claim, contact Kohler Co., either through your Dealer, Plumbing

Contractor, Home Center or E-tailer, or by writing: Kohler Co., Attn.: Customer Care Center, 444 Highland

Drive, Kohler, WI 53044, USA. Please be sure to provide all pertinent information regarding your claim,

including a complete description of the problem, the product, model number, color, ﬁnish, the date the

product was purchased and from whom the product was purchased. Also include your original invoice. For

other information, or to obtain the name and address of the service and repair facility nearest you call

1199249-2-A 16 Kohler Co.

Warranty (cont.)

1-800-4-KOHLER (1-800-456-4537) from within the USA and Canada, and 001-800-456-4537 from within

Mexico, or visit www.kohler.com within the USA, www.ca.kohler.com from within Canada, or

www.mx.kohler.com in Mexico.

KOHLER CO. AND/OR SELLER ARE PROVIDING THIS WARRANTY IN LIEU OF ALL OTHER

WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED

WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. KOHLER CO.

AND/OR SELLER DISCLAIMS ANY LIABILITY FOR SPECIAL, INCIDENTAL OR CONSEQUENTIAL

DAMAGES.

Some states/provinces do not allow limitations on how long an implied warranty lasts, or the exclusion or

limitation of special, incidental or consequential damages, so these limitations and exclusions may not apply

to you. This warranty gives the consumer speciﬁc legal rights. You may also have other rights, which vary,

from state/province to state/province. This warranty is to the original consumer purchaser only, and

excludes product damage due to installation error, product abuse, or product misuse, whether performed by

a contractor, service company or the consumer.

This is Kohler Co.’s exclusive written warranty.

Warranty

ONE-YEAR LIMITED WARRANTY

KOHLER plumbing products are warranted to be free of defects in material and workmanship for one year

from date of installation.

Kohler Co. will, at its election, repair, replace or make appropriate adjustment where Kohler Co. inspection

discloses any such defects occurring in normal usage within one (1) year after installation. Kohler Co. is not

responsible for removal or installation costs. Use of in-tank toilet cleaners will void the warranty.

To obtain warranty service contact Kohler Co. either through your Dealer, Plumbing Contractor, Home

Center or E-tailer, or by writing Kohler Co., Attn.: Customer Care Center, 444 Highland Drive, Kohler, WI

53044, USA, or by calling 1-800-4-KOHLER (1-800-456-4537) from within the USA and Canada, and

001-800-456-4537 from within Mexico, or visit www.kohler.com within the USA, www.ca.kohler.com from

within Canada, or www.mx.kohler.com in Mexico.

IMPLIED WARRANTIES INCLUDING THAT OF MERCHANTABILITY AND FITNESS FOR A

PARTICULAR PURPOSE ARE EXPRESSLY LIMITED IN DURATION TO THE DURATION OF THIS

WARRANTY. KOHLER CO. AND/OR SELLER DISCLAIM ANY LIABILITY FOR SPECIAL,

INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states/provinces do not allow limitations on how

long an implied warranty lasts, or the exclusion or limitation of special, incidental or consequential damages,

so these limitations and exclusions may not apply to you. This warranty gives you speciﬁc legal rights. You

may also have other rights which vary from state/province to state/province.

This is Kohler Co.’s exclusive written warranty.

Warranty

For Mexico

KOHLER CO.

It is recommended that at the time of purchase, you verify that all accessories and components are complete

in this package.

This Kohler product is warranted to be free of defects in material and workmanship for one (1) year from the

date of purchase as shown on the invoice or receipt.

1. Kohler Co. will only service its commercialized products through its authorized distributors.

2. To obtain warranty service, please present the invoice and corresponding warranty.

3. Through its authorized distributors, Kohler Co. promises to repair the defective product or provide a new

Kohler Co. 17 1199249-2-A

Warranty (cont.)

replacement or an equivalent model (in those cases that the model has been discontinued) when the product

is beyond repair, without any charge to the consumer.

4. The time of repair will not exceed six (6) weeks commencing on the date the product is received.

5. It is recommended that the consumer save the invoice or receipt as additional protection, as it may

substitute the warranty in the case that there is a discrepancy in the validity of the warranty.

EXCEPTIONS AND RESTRICTIONS

The Warranty will not be valid in the following cases:

1. When the product is not operated in accordance with the instructions concerning use and operation set

forth in the owner’s manual or installation instructions, and when the recommendations and warnings

included are not observed.

2. When the product has been modiﬁed or dismantled partially or totally; or has been used in a negligent

fashion and as a consequence has suffered damages attributable to the consumer, individual, or hardware not

authorized by Kohler Co.

3. This warranty does not cover the damages as a result of disaster such as ﬁre or acts of God, including

ﬂooding, earthquake, or electric storms, etc. To obtain a list of distributors in your area where you can

exercise your rights under this warranty, please call 001-800-456-4537.

KOHLER CO., KOHLER, WI 53044 U.S.A.

IMPORTER:

INTERNACIONAL DE CERÁMICA, S.A.B. DE C.V.

AV. CARLOS PACHECO NO. 7200

CHIHUAHUA, CHIH., MEXICO C.P. 31060

TEL: 52 (14) 29-11-11

Troubleshooting

NOTICE: This section is for general aid only. A Kohler Co. Authorized Service Representative or qualiﬁed

electrician should correct any electrical problems. For warranty service, call 1-800-4KOHLER from within

the USA and Canada, or 001-800-456-4537 from within Mexico.

NOTE: The product model number is printed on a label on the blower side of the bath.

NOTE: For service parts information, visit your product page at www.kohler.com/serviceparts.

Troubleshooting the Bath System

Symptoms Probable Causes Recommended Action

1. User keypad does not

illuminate when Power

icon is pressed or the

outer ring is rotated.

A. No power to control. A. Check wiring and connect power.

B. Ground-Fault Circuit-Interrupter

(GFCI) or Residual Current

Device (RCD) tripped.

B. Reset GFCI or RCD. If it trips

again, refer to ″Ground-Fault

Circuit-Interrupter (GFCI) or

Residual Current Device (RCD)

trips when bath is turned on.″

C. Wiring harness from user

keypad to control is loose,

disconnected or damaged.

C. Check wiring for proper

connections. Replace the wiring

harness if necessary.

D. User keypad does not work. D. Replace the user keypad.

E. Control does not work. E. Replace the control.

1199249-2-A 18 Kohler Co.

Troubleshooting (cont.)

Symptoms Probable Causes Recommended Action

2. Ground-Fault

Circuit-Interrupter (GFCI)

or Residual Current

Device (RCD) trips when

bath is turned on.

A. Electrical harness is wet or

damaged.

A. Check for wet connections. Dry the

connections and repair the leak.

Check for insulation or connector

damage. Replace the harness if

damaged.

B. Electrical wiring to the bath

junction box is wet or damaged;

or the power amperage is

inadequate.

B. Have a qualiﬁed electrician

diagnose and correct the problem

in accordance with applicable

building and electrical codes; or

increase the power amperage to 20

A.

C. Electrical wiring to the bath

power cord is wet or damaged.

C. Have a qualiﬁed electrician

diagnose and correct the problem

in accordance with applicable

building and electrical codes.

D. Blower motor is shorted

internally.

D. Replace the blower motor.

E. Control is shorted internally. E. Replace the control.

3. User keypad is

illuminated, but does not

respond to icons or outer

ring.

A. Control program is locked. A. Reset GFCI or RCD.

B. P5 plug assembly harness from

user keypad to control is loose,

disconnected, or damaged.

B. Check wiring for proper

connections. Replace the wiring

harness if necessary.

C. User keypad does not work. C. Replace the user keypad.

D. Control does not work. D. Replace the control.

4. Blower motor will not

start.

A. Power cord from blower motor

to control is loose, disconnected,

or damaged.

A. Check wiring for proper

connections.

B. Blower motor does not work. B. Replace the blower motor.

C. Control does not work. C. Replace the control.

5. Blower motor stops

running and will not

immediately restart.

Keypad is illuminated.

A. Blower motor overheated and

protection device activated.

A. Check for blockage at air inlet.

Remove blockage and allow motor

to cool. Refer to ″User keypad is

illuminated, but does not respond

to icons or outer ring. Blower

motor will not start.″

6. Blower motor starts, some

but not all airjets are

bubbling.

A. Blower motor speed is too low. A. Increase speed set point to blower

motor.

B. Blower air inlet is blocked. B. Clear blower air inlet.

C. Blower motor does not work. C. Replace the blower motor.

D. Blower motor discharge is

blocked.

D. Clear blockage.

E. Check valve does not work. E. Replace the check valve.

F. Airjets are clogged. F. Use a small between-the-teeth

dental brush and white vinegar.

Dip the brush in the vinegar, brush

the hole, rinse the brush in clean

water, and then use the wet rinsed

brush to rinse the hole.

G. Some zones are closed. G. Operate all zones.

Kohler Co. 19 1199249-2-A

Troubleshooting (cont.)

Symptoms Probable Causes Recommended Action

7. Blower motor runs but no

air bubbles are formed.

A. Blower air inlet is blocked. A. Clean blower air inlet.

B. Airjets are clogged. B. Use a small between-the-teeth

dental brush and white vinegar.

Dip the brush in the vinegar, brush

the hole, rinse the brush in clean

water, and then use the wet rinsed

brush to rinse the hole.

C. Check valve does not work. C. Replace the check valve.

D. Blower motor does not work. D. Replace the blower motor.

E. Control does not work. E. Replace the control.

8. Blower motor operates,

air bubbles are formed,

zone controls work, but

variable speed feature

does not work.

A. Blower air inlet is blocked. A. Clear blower air inlet.

B. Loose, disconnected, or

damaged wiring harness.

B. Check wiring for proper

connections. Replace the wiring

harness if necessary.

C. User keypad does not work. C. Replace the user keypad.

D. Blower motor does not work. D. Replace the blower motor.

E. Control does not work. E. Replace the control.

9. Blower motor won’t turn

off when the Power icon

on user keypad is

pressed.

A. User keypad does not work. A. Replace the user keypad.

B. Loose, disconnected, or

damaged wiring harness.

B. Check wiring for proper

connections. Replace the wiring

harness if necessary.

C. Control does not work. C. Replace the control.

10. A zone does not produce

air bubbles but another

zone operates normally.

A. Zone is not selected. A. Select the zone according to the

instructions in the ″Operating

Instructions″ section.

B. Butterﬂy valve does not work. B. Replace the butterﬂy valve.

C. Loose, disconnected, or

damaged wiring harness.

C. Check wiring for proper

connections. Replace the wiring

harness if necessary.

D. User keypad does not work. D. Replace the user keypad.

E. Control does not work. E. Replace the control.

11. Surge mode does not

work.

A. User keypad does not work. A. Replace the user keypad.

B. Control does not work. B. Replace the control.

12. Water spillage or damage

observed under the bath.

A. Drain or overﬂow leaking. A. Repair or replace the drain

assembly according to the

manufacturer’s instructions.

B. Wall, deck, and/or shower door

is improperly sealed.

B. Apply silicone sealant at the seams

between the bath and the wall,

deck, or door.

C. Cracked piping or air channels. C. Refer to the manufacturer.

13. Bath does not purge

automatically.

A. Level sensor wires are

disconnected.

A. Connect the level sensor wires.

Chromatherapy (if equipped)

Symptoms Probable Causes Recommended Action

14. Chromatherapy lights do

not work.

A. Loose, disconnected or damaged

wiring/connections.

A. Check wiring for proper

connections. Replace wiring if

necessary.

B. Control does not work. B. Replace control.

15. Chromatherapy does not

cycle.

A. Chromatherapy harness

assembly does not work.

A. Replace the chromatherapy harness

assembly.

1199249-2-A 20 Kohler Co.

Page is loading ...

Kohler 856-GH0-0 User manual

Kohler 856-GH0-0 User manual

in other languages

Related papers

Other documents