2216E DIN Rail Mounting Controller
MOUNTING DETAILS
The controller can be mounted either on a flat surface or on DIN rail. For rail mounting use
symmetrical DIN rail 35 x 7.5mm or 35 x 15mm. For mounting on a flat surface use the (A) holes
provides. Use M4 screws tightened with a torque of 1Nm.
The dimensions are as follows:
Mounting Removing
CONTENTS
• INTRODUCTION
• CONFIGURATION
• ELECTRICAL CONNECTIONS
• MOUNTING DETAILS
INTRODUCTION
This version of the 2216e controller is designed specifically for DIN rail or flat surface mounting. The
operation and performance is identical to that of the panel mounting 2216e - apart from the use of
external CJC compensation – see below. Please therefore, refer to the main handbook for
configuration and operation instructions.
The 2216e can be used as a temperature or process controller, independent alarm unit, or as an
isolating signal conditioner. It can operate standalone, or be connected to an operator panel,
Programmable Logic Controller or Supervisory Control System using Modbus or Devicenet
communications.
This version of the 2216e contains special firmware to measure the cold junction temperature at the
terminals of the DIN housing. A Pt100 sensor, mounted under the input terminals, is used to measure
the cold junction temperature.
Please note: because of the external CJC sensing, the Pt100 input is not supported.
CONFIGURATION
In configuration level external cold junction sensing must be selected. This is done in the O0 list by
selecting ?6 as the % reference temperature.
The configuration and operation of this controller is otherwise identical to that of the standard 2216e
panel mounting controller.
ENG
2216e DIN Rail Controller Handbook Addendum Specials Number EU0492
%
?6
133
(A)
(A)
(A) (A)
Part No: HA027439 Issue 1.0 Applies to controller s/w version A3.56 1
2216e DIN Rail Controller Handbook Addendum Specials Number EU0492
Part No: HA027439 Issue 1.0 Applies to controller s/w version A3.56 4
ELECTRICAL CONNECTIONS
The connections are as follows:
ELECTRICAL CONNECTIONS - CONTINUED
Line
Neutral
1 2 3 4 5 6 7 8
910111213141517
Output
1
Sensor
Input
Output
2
Output
3
100 - 240Vac
+-
------ Digital Communications ------
2216E
Input
Thermocouple
Volts or mV
9
10
0-10Vdc or
0-80mV
+
-
9
10
+
-
mA input
9
10
2.49ohm
+
-
Modbus
4-wire
RS485
2-wire
RS232
11
12
13
14
15
16
--------- Common ------------
--------- Not used ------------
Rx+
Rx-
A(+)
B(-)
Tx+
Tx-
Tx
Rx
---- Not used ----
---- Not used ----
2216e DIN Rail Controller Handbook Addendum Specials Number EU0492
2216e DIN Rail Controller Handbook Addendum Specials Number EU0492
Part No: HA027439 Issue 1.0 Applies to controller s/w version A3.56 3Part No: HA027439 Issue 1.0 Applies to controller s/w version A3.56 2
Outputs 1, 2 & 3
Output 1
3
4
+
-
+
-
Output 2
5
6
Relay Logic Triac
+
-
Output 3
7
8
Relay
Contact
input
Relay Logic Triac
Devicenet
V+
CAN_H
SHIELD
CAN_L
V-
Not used
CAN
Label
Color
Chip
Red
White
None
Blue
Black
Not used
11
12
13
14
15
16
-
1
-
2
Eurotherm 2216e DIN Rail Controller Handbook Addendum Owner's manual
- Type
- Owner's manual
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Eurotherm 2216e Owner's manual
-
-
Eurotherm Контроллеры серии 2200 Owner's manual
-
-
-
-
-
Eurotherm 2204e/2208 Owner's manual
-
-
Other documents
-
Nortel Application Switch 2424-SSL Product Brief
-
MRC 2000 User manual
-
Eurotherm controls 847 User manual
-
MRC 3200 User manual
-
Omega CN2204 Owner's manual
-
-
-
Allen-Bradley 1769-L18ERM-BB1B User manual
-
Chromalox C4 User manual
-
Allen-Bradley 2080-OF2 User manual
