Copystar FS-4020DN 120V60HZ/PAGE PRINTER Installation guide

Copystar
Brand
Copystar
Model
FS-4020DN 120V60HZ/PAGE PRINTER
Type
Installation guide

This manual is also suitable for

Installation Guide
Clearance
• Temperature: 10 to 32.5 °C (50 to 90.5 °F)
• Humidity: 15 to 80 %RH
• Power Supply: 120 V AC, 60 Hz, 7.7 A / 220 to 240 V AC, 50/60 Hz, 4.3 A
Environment
Important: Do not install the printer where temperature or humidity is outside the
recommended range. Print quality may suffer and there will be an increased chance of paper
jams.
300 mm
(11-13/16")
100 mm
(3-15/16")
200 mm
(7-7/8")
600 mm
(23-5/8")
List of Shipped Components
Installing the Toner Container and Waste Toner Box
Open the top cover and remove the
fixing tape.
Take the toner container from the bag.
1
300 mm
(11-13/16")
Important: When carrying the printer,
always hold the right and left sides as shown.
Insert the protrusion at the left of the rear cover into the hole in the printer. The rear
cover is fixed.
12
Installing the Rear Cover
CAUTION: Be sure to provide enough space around printer. Prolonged use
without sufficient clearance may cause overheating.
Shake the new toner container at least
10 times as shown in the figure in order
to distribute the toner evenly inside the
container.
3
2
Install the toner container into the
printer.
5
Push on the PUSH marks on the toner
container until the container clicks into
place.
6
Close the top cover. Open the cap of the waste toner box.
8
Open the left cover.
9
10
Close the left cover.
11
Carefully remove the printer and other items from the box.
Check that nothing is missing against the list of shipped components.
Make sure that the place of installation meets the following requirements.
1
3
2
Remove the label from the toner
container.
4
Before you can use the printer for the
first time, you must prepare it by
installing the toner container and waste
toner box.
CD-ROM
Manual and Other
Printed Materials
Rear Cover
Printer
Toner Container
Waste Toner Box
Plastic Waste Bag
Language Label
Sheet
Attach the included language label
sheet on the indicator as shown in the
figure.
Attaching the Label
Power Cord
FS-2020D/FS-3920DN/FS-4020DN
Insert the protrusion at the right of the rear cover into the hole in the printer.
7
Insert the new waste toner box as
shown in the figure. When the box is
set correctly, it will snap into place.
Turn the power switch to on ( | ).
Important: The printer will begin replenishing the toner; this will take approximately 15
minutes.
Selecting the Message Language
1
Printed in China 302J056020 Rev.1.0 2008.9
Connect the printer to the PC or your network device. Use shielded interface cables.
These cables are sold separately.
Remove the cap, when using the network interface.
Important: Installing the optional network interface card on the FS-2020D model enables the
network function.
1
Connecting Cables
5
6
Adding Paper to the Paper Cassette
4
The paper cassette can accommodate
A6(FS-2020D model:A5) to A4/Letter
and Legal size paper and can hold
approximately 500 sheets.
Turn the paper size dial so that the size
of the paper you are going to use
appears in the paper size window.
Pull the release lever on the left side
guide and slide to the desired paper
size.
3
Pull the release lever and slide the
paper stopper to the desired paper
size.
5
Fan the paper, then tap it on a level
surface to avoid media jams or skewed
printing.
6
Place the paper in the cassette, with
side to be printed downward, so that
the leading edge is aligned against the
paper stopper.
7
Set the stack of paper so that it is under
the clips as shown.
8
Important: Do not load more paper than
will fit under the load limit marks (T T) on
the paper guides.
Insert the paper cassette into the slot in
the printer. Push it straight in as far as
it will go.
9
If you are going to set paper that is
longer than A4/Letter, pull out the
extension paper cassettes pushing the
lock lever one by one and adjust them
to the desired paper size.
4
Pull out the paper cassette.
1
© 2008 by KYOCERA MITA Corporation All rights reserved. 2-28, 1-Chome, Tamatsukuri, Chuo-ku, Osaka 540-8585, Japan
Connect the power cord to the printer
and the other end into a power outlet.
2
To change the language, press [U] or [V] repeatedly until the message display
shows the desired language.
2
3
Wait until the message display indicates MSG Language. The default message
language is English.
Important: MSG Language may not appear according to the destination.
Press [OK]. The message language will be changed.
4
Refer to the Operation Guide to set network parameters and to install the printer driver.
2
Cap
  • Page 1 1
  • Page 2 2

Copystar FS-4020DN 120V60HZ/PAGE PRINTER Installation guide

Copystar
Brand
Copystar
Model
FS-4020DN 120V60HZ/PAGE PRINTER
Type
Installation guide
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents