KYOCERA ECOSYS FS-1350DN Installation guide

ECOSYS FS-1350DN
KYOCERA
Brand
KYOCERA
Model
ECOSYS FS-1350DN
Category
Toners & Laser Cartridges
Type
Installation guide

This manual is also suitable for

Installation Guide
Clearance
• Temperature: 10 to 32.5 °C (50 to 90.5 °F)
• Humidity: 15 to 80 %RH
• Power Supply: 120 V AC, 60 Hz, 7.5 A / 220 to 240 V AC, 50/60 Hz, 3.9 A
FS-1350DN
Environment
CAUTION: Be sure to provide enough space around printer. Prolonged use
without sufficient clearance may cause overheating.
300 mm (11-13/16") 300 mm (11-13/16") 200 mm (7-7/8") 500 mm (19-11/16")
Unpacking
CD-ROM Manuals and Other
Printed Materials
Printer
Power CordToner Container
Installing the Toner Container
Open the top cover. Turn the lock lever to the unlock
position.
Take the toner container from the bag.
Shake the new toner container at least
5 times as shown in the figure in order
to distribute the toner evenly inside the
container.
Turn the lock lever to the lock position.Push firmly on the top of the container
at the positions marked PUSH, until
you hear a click.
Remove the label from the toner
container.
Close the top cover.
2
1
1 32
6785
Install the new toner container into the
printer.
200 mm
(7-7/8")
Unpack the printer and all its included
components.
Remove the packing item. Check the parts and components.
1 32
4
Important: Do not install the printer where temperature or humidity is outside the
recommended range. Print quality may suffer and there will be an increased chance of paper
jams.
Pull the paper cassette all the way out
of the printer.
Loading Paper
Fan the paper, then tap it on a level
surface to avoid media jams or skewed
printing.
Adjust the paper width guides to fit the
paper size.
Adjust the paper length guide to fit the
paper size.
Load paper in the cassette, with the
side to be printed downward.
Insert the paper cassette into the slot in
the printer. Push it straight in as far as
it will go.
3
2
5
31
6
4
Connect the power cord to the printer
and the other end into a power outlet.
Connect the printer to the PC or your
network device. Use shielded interface
cables. These cables are sold
separately.
Connecting Cables
4
12
Selecting the Message Language
To change the language, press [U] or [V] repeatedly until the message display
shows the desired language.
Press [OK]. The message language will be changed.
5
21
3
4
© 2008 by KYOCERA MITA Corporation All rights reserved. 2-28, 1-Chome, Tamatsukuri, Chuo-ku, Osaka 540-8585, Japan Printed in China 302H456020 Rev.1.0 2008.9
Refer to the Operation Guide to install the printer driver and to set network parameters.
Wait until the message display indicates MSG Language. The default message
language is English.
Important: MSG Language may not appear according to the destination.
Important: Do not exceed the upper limit
of the cassette. Otherwise, it may cause
paper jams.
Note: Remove the cap, when using the
network interface.
Turn the power switch on (|).
Important: The printer will begin replenishing the toner; this will take approximately
15 minutes.
  • Page 1 1
  • Page 2 2

KYOCERA ECOSYS FS-1350DN Installation guide

ECOSYS FS-1350DN
KYOCERA
Brand
KYOCERA
Model
ECOSYS FS-1350DN
Category
Toners & Laser Cartridges
Type
Installation guide
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents