Obaby Lisa Cot Bed Instructions Manual

Obaby
Brand
Obaby
Model
Lisa Cot Bed
Category
Baby furniture
Type
Instructions Manual

Obaby Lisa Cot Bed

Obaby Lisa Cot Bed is a high-quality and durable cot bed that can be used from birth to approximately four years old. It is made from solid wood and has a sturdy construction. The cot bed has three adjustable base heights, so you can lower the base as your child grows. It also has two removable side rails, so you can convert it into a junior bed when your child is ready. The Obaby Lisa Cot Bed is a great choice for parents who are looking for a stylish and practical cot bed that will last for years to come.

Here are some of the features and possible use cases of the Obaby Lisa Cot Bed:

Obaby Lisa Cot Bed

Obaby Lisa Cot Bed is a high-quality and durable cot bed that can be used from birth to approximately four years old. It is made from solid wood and has a sturdy construction. The cot bed has three adjustable base heights, so you can lower the base as your child grows. It also has two removable side rails, so you can convert it into a junior bed when your child is ready. The Obaby Lisa Cot Bed is a great choice for parents who are looking for a stylish and practical cot bed that will last for years to come.

Here are some of the features and possible use cases of the Obaby Lisa Cot Bed:

IMPORTANT
PLEASE READ THESE INSTRUCTIONS CAREFULLY BEFORE USING THIS PRODUCT
KEEP FOR FUTURE REFERENCE
Lisa Cot Bed
Page One
www.obaby.co.uk
www.obaby.co.uk
Thank you for choosing O Baby. To ensure that your cot bed is used in
accordance with these instructions, please read them fully and retain for future reference.
If you have any problems please contact O Baby - info@obaby.co.uk or 0845 078 0290
BEFORE ASSEMBLY
- Unpack all the parts and identify them against the fittings and components lists.
- Do not discard any packing until you are sure you have all the parts and the pack of fittings
- If you do not find the missing parts or if you find any damages call the O Baby helpline 0845 078 0290
- Read the instructions thoroughly before attempting to construct the cot/cot bed.
- You may find the construction of your cot/bed easier if you have the help of another person.
- Follow each stage of construction step-by-step.
- It may be unsafe to use replacement part or accessories
Page Two
www.obaby.co.uk
Parts
A. Allen key x 1
B. Long assembly screw x 8
C. Short assembly screw x 8
D. Barrel nuts x 16
Cot bed head end & Foot end panel
(Foot end has the O Baby logo facing the outside of the cotbed)
Cot bed base
Fixed sides x 2
A
B C
D
Page Three
www.obaby.co.uk
Assembling your cot bed
Step 1
Starting on one end of the base fit the barrel nuts in the holes
provided on the base corners .
Ensure the slits are facing the inside of the base.
Step 2
Decide how high you would like your base;
- For a new born - to make it easier for the parent the base can be at
its highest.
- Once the child can start to sit up unaided you should lower the base
to prevent the baby climbing out or over the rails.
Once you have decided what level you are fitting the base,
fit the long screws in the 2 holes in the base
Step 3
Using your allen key & the long screws fit the base to the
first end & then fit the other end the same way.
2 x long screws per side (8 in totaly for the base).
Highest level for new borns until they can sit up unaided
Middle Level for babies sitting up until they are standing/climbing
Lowest Level for babies that can stand
Top Tip! don’t tighten all the screws fully until you have completed assembling.
Page Four
www.obaby.co.uk
Assembling your cot bed
Step 4
Now add the first side rail, starting by attaching the tops first.
Put the barrel nut in the side rail, then thread the long screw through
the cot end & then through the rail and tighten it up into the barrel nut.
Do this on the other end of this rail
Step 5
Now do the same but for the bottom of the side panels.
Step 6
Now go around the whole cot bed and tighten every screw completely.
Page Five
www.obaby.co.uk
Changing the Cot into a Junior Bed
Step 1
Remove both side rails using the allen key.
Only change into a Junior bed when your are confident that you child will be safe without the side rails.
Step 2
Fit the base to the lowest level using the same fittings for the base
that were used for the Cot.
Step 3
Tighten all the screws properly.
Safe Use & Maintenance Page
www.obaby.co.uk
www.obaby.co.uk
INSTRUCTIONS FOR SAFE USE & MAINTENANCE
READ CAREFULLY BEFORE USING THIS PRODUCTS & KEEP FOR FUTURE REFERENCE.
- The lowest position for the cot base is the safest. This position should always be used once the baby
is old enough to sit up.
- Never leave anything in the cot which could provide a foothold for your child to climb out or
would present a danger of suffocation or strangulation.
- All assembly fittings should be tightened properly and care should be taken to ensure that no screws
are loose, a child could trap parts of the body, or clothing (e.g. ribbons, drawstrings, necklaces this
could pose strangulation.
- Regually check that all fittings and components of the cot/bed are fully tightened and in working order.
If any parts have become worn or damaged then do not use the cot/bed, seek advice from your retailer
or contact O Baby’s Customer Care - info@obaby.co.uk or 0845 078 0290.
- Do not use replacement parts that are not recommended or supplied by O Baby. Non approved parts
may render the cot/bed unsafe or may be considered product damage or misuse, voiding the warranty.
- Do not place you cot/bed in the close proximity of an open fire and other sources of heat, such as
radiators, electric or gas fires.
- We recommend you use the O Baby Mattress Size 140 x 69cm for this Cot Bed.
- The mattress should be no more then 40mm shorter or narrower than the internal length or width of the
cot/bed.
- The thickness of the mattress chosen should be such that the distance between the surface of the
mattress to the upper edge of the cot sides is a minimum of 500mm when the base is set in the lowest
position and a minimum of 200mm when the cot base is set in the highest position.
- Your cot/bed may be cleaned with a damp cloth. Never use bleach or harsh abrasives.
- Due to constant updating and improvements, some components may occasionally differ slightly from
diagrams shown in these instructions. We reserve the right to change the specifications of any products
without prior notice.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7

Obaby Lisa Cot Bed Instructions Manual

Obaby
Brand
Obaby
Model
Lisa Cot Bed
Category
Baby furniture
Type
Instructions Manual

Obaby Lisa Cot Bed

Obaby Lisa Cot Bed is a high-quality and durable cot bed that can be used from birth to approximately four years old. It is made from solid wood and has a sturdy construction. The cot bed has three adjustable base heights, so you can lower the base as your child grows. It also has two removable side rails, so you can convert it into a junior bed when your child is ready. The Obaby Lisa Cot Bed is a great choice for parents who are looking for a stylish and practical cot bed that will last for years to come.

Here are some of the features and possible use cases of the Obaby Lisa Cot Bed:

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents