Maytag C6B(A,H)-X Installation guide

C6B(A,H)-X
Maytag
Brand
Maytag
Model
C6B(A,H)-X
Type
Installation guide

This manual is also suitable for

SPLIT SYSTEM INDOOR COILS
ABOUT THE CONVERSION KIT
The horizontal conversion kit is designed to allow cased
coils to be mounted in the horizontal right or the horizontal
left position. NOTE: The position is determined by airflow
direction when looking at the front of the unit as shown in
Figure 1. Before converting the Cased Coil to a horizontal
configuration, determine if the installation is a horizontal
left or right application. The kit must be installed before
the refrigerant lines are connected.
INSTALLATION
1. Remove the coil access doors.
2. Slide the coil straight out the front of the unit.
3. Remove the knockouts from the front and rear delta
plates. See Figure 2.
IMPORTANT NOTE: The coil has two sets of 1/4"
knockouts; one set in the front delta plate and one set
in the rear delta plate. The holes are used for holding
the coil support rod in either horizontal application (left
or right). It is important that only one hole from each
set is opened. If the wrong hole is opened, seal it with
metal tape to prevent air leakage. To determine which
holes to open, locate your installation type in Figure 1.
For 26" or 30" tall cabinets, skip to step 6.
4. Prepare the horizontal drain pan for installation by
cleaning the 1" x 5/8" recessed areas (bottom of the
pan)with the alcohol wipe supplied in the kit.
5. Peel off the paper backing from the mounting tape on
the back of the clips and mount them in the cleaned
recessed areas of the drain pan. NOTE: To determine
which end of the pan to mount the clips on, locate your
installation type in Figure 3 Install the clips with the open
end facing inwards as shown in Figure 3.
6. Install the coil support rod by inserting the ends of the
rod into the knocked out holes as shown in Figure 2.
NOTE: The coil support rod with the tabs on the end
goes in the holes that are in the front of the coil. Make
sure the rod ends clear the copper parts of the coil when
installed with the drain pan in step 8.
7. Attach the horizontal drain pan to the coil as shown in
Figure 2.
8. Install the plastic plug into the open hole of the bottom
drain pan to block bypass air flow. See Figure 2.
9. Place the insulation sheet (supplied with the kit) inside
the coil cabinet to support the horizontal drain pan
assembly.
10. Place the coil and drain pan assembly back into the
cabinet as shown in Figure 1.
• For cabinets that are 20” tall: Slip the bottom flange
of the drain pan extension under the coil support rod
in the drain pan. Make sure the side tabs fit inside the
drain pan on each side between the drain pan inside
wall and the coil support rod. See Figure 4.
• For cabinets that are 26 or 30” tall: The holes in the
drain pan extension should be pressed over the nibs
molded into the drain pan. To determine which pair
of holes to use depends on how the unit is installed
horizontally (left or right). Verify proper positioning
for clearance thru the top of the coil cabinet before
affixing.
NOTE: The drain pan extension should extend into
the existing ductwork several inches. The drain pan
extension can be installed and removed after the
ductwork has been attached to the cased coil.
11. Reinstall the doors and secure with their screws.
HORIZONTAL CONVERSION KIT
INSTALLATION INSTRUCTIONS
IMPORTANT
It is your responsibility to know how to properly operate the equipment according to strict safety
guidelines and maintaining it for the life of the product. Safety should always be the deciding
factor when using this device and using common sense plays an important role as well. Pay
attention to all safety warnings and any other special notes highlighted in the manual.
These instructions are primarily intended to assist qualified individuals experienced in the
proper usage of this equipment. Please read all instructions carefully before using this device.
Improper usage of this equipment or failure to follow safety warnings could result in serious
injury, death, or property damage.
DO NOT DESTROY. PLEASE READ CAREFULLY & KEEP IN A SAFE PLACE FOR FUTURE REFERENCE.
Figure 1. Horizontal Configurations
(with Drain Pan Extension)
SUPPORT ROD
DRAIN PAN
EXTENSION
DUCT FLANGE
HORIZONTAL DRAIN PAN
(SHOWN W/CUTAWAYVIEW)
BOTTOM FLANGE SLIPPED
UNDER SUPPORT ROD
708914A (Replaces 7089140)
HORIZONTAL LEFT
CONFIGURATION
HORIZONTAL RIGHT
CONFIGURATION
AIRFLOW
AIRFLOW
HORIZONTAL RIGHT
HORIZONTAL LEFT
PLUG
PLUG
KNOCKOUTS
(FRONT & REAR DELTA PLATES)
SUPPORT
ROD
SUPPORT
ROD
Figure 2. Drain Pan Installation
Figure 4. Drain Pan Extension
Figure 3. Support Rod Clip Locations
HORIZONTAL RIGHT
CLIP LOCATIONS
HORIZONTAL LEFT
CLIP LOCATIONS
Specifications & illustrations subject to change without notice or incurring obligations (05/15).
O’Fallon, MO, © Nortek Global HVAC LLC 2015. All Rights Reserved.
  • Page 1 1
  • Page 2 2

Maytag C6B(A,H)-X Installation guide

C6B(A,H)-X
Maytag
Brand
Maytag
Model
C6B(A,H)-X
Type
Installation guide
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents