Triax CGS 470 Assembly Instruction Manual

Triax
Brand
Triax
Model
CGS 470
Type
Assembly Instruction Manual
AssemblyInstruction
CGS470
Model Itemno.
CGS 470 325010
Version 18 Date 01/2017 EN
- 2 - CGS 470
Contents
1 Safety regulations ..............................................................................................3
2 General information ..........................................................................................3
2.1 Scope of delivery ............................................................................... 3
2.2 Meaning of the symbols used ............................................................... 4
2.3 Technical data.................................................................................... 4
2.4 Description ........................................................................................ 5
3 Installation ........................................................................................................7
3.1 Retrofitting a CA module ..................................................................... 7
3.2 Setting the operating voltage of the CA module ..................................... 8
3.3 Installing the digital module ................................................................. 9
3.4 Connecting the digital module ........................................................... 10
4 The control panel at a glance ...........................................................................11
4.1 Menu items ...................................................................................... 11
4.2 Functions of the control panel buttons .................................................. 11
5 Programming ..................................................................................................12
5.1 Preparation...................................................................................... 12
5.2 Programming procedure .................................................................... 13
5.3 Programming the digital module ......................................................... 15
Selecting the module / channel strip ................................................... 16
Tuner .............................................................................................. 16
LNB oscillator frequency .................................................................... 17
CA module, Card information ............................................................ 18
Input symbol rate .............................................................................. 18
Input frequency ................................................................................ 19
Station filter ..................................................................................... 20
Audio stream for a TV channel ........................................................... 21
Volume level .................................................................................. 21
Identification of the stereo / dual tone ................................................. 22
Selecting the picture format ............................................................... 22
Picture format signal, Teletext mode .................................................... 23
Activating test lines ........................................................................... 23
Teletext subtitle pages and Standard ................................................... 24
Activating teletext subtitle pages and setting the standard ................ 24
Activating DVB subtitle pages ....................................................... 25
Black bar ................................................................................... 25
Storing data .................................................................................... 26
6 Final procedures ..............................................................................................27
- 3 - CGS 470
1 safety regulations
• The standards IEC/EN/DIN EN 50083 resp. IEC/EN/DIN EN 60728 must
be observed.
• Do not perform installation and service work during thunderstorms.
• Assembly, installation and servicing should be carried out by authorised
electricians.
• Switch off the operating voltage of the system before beginning with assem-
bly or service work.
• Avoid short circuits!
• Observe the relevant standards, regulations and guidelines on the installa-
tion and operation of antenna systems.
• To ensure electromagnetic compatibility, make sure all connections are tight
and the covers are screwed on securely.
• No liability is accepted for damage caused by faulty connections or inap-
propriate handling of the device.
Check the head-end station CSE 2800 according to the safety instructions
listed in their assembly instruction.
Take precautions to prevent static discharge when working on the device!
Electronic devices should never be disposed of in the household rubbish. In
accordance with directive 2002/96/EC of the European Parliament and the
European Council from January 27, 2003 which addresses old electronic and
electrical devices, such devices must be disposed of at a designated collection
facility. At the end of its service life, please take your device to one of these
public collection facilities for proper disposal.
2 general information
2.1 sCope of delivery
1 CGS 470 module
1 AV cable
1 CD (assembly instructions)
1 Brief Assembly Instructions
- 4 - CGS 470
2.2 meaning of the symbol s used
Important note
—> General note
–
/
–
/
Optional use of the buttons
• Performing works
2.3 teChniCal data
The requirements of the following are met:
2011/65/EU, 2014/30/EU, 2014/35/EU
The product fulfils the guidelines and standards for CE labelling.
Unless otherwise noted all values are specified as "typical".
RF input:
Frequency range: ....................................................... 950 … 2150 MHz
Level: ..................................................................... 60 dBμV … 80 dBμV
Input impedance: ...............................................................75 Ω, nominal
Return loss: .....................................................................................8 dB
Input data rate: ...............................................................1 … 45 MSymb
Remote power supply: .................. 12 V / 350 mA
(switch-off at short-circuit)
Output specifications:
Audio
Noise voltage ratio rated (DIN 45633): ...........................................60 dB
Non-linear distortion factor: ............................................................0.6 %
Frequency range: ..........................................................20 Hz … 15 kHz
Level at -12 dB: .......................................................................500 mV
rms
Impedance: ............................................................................ max. 1 kΩ
Video
Signal-to-noise ratio:.............................................................58 dB (rated)
Level (75 Ω): ..................................................................................1 V
pp
Impedance: .................................................................................... 75 Ω
Connections:
SAT inputs: ............................................................................ 2 F-sockets
Connection strip (20-pin): ...................
For supply voltages and control circuits
AV output: ...........................................................................
26-pin
socket
- 5 - CGS 470
2.4 desCription
The module
CGS 470
, in the following called digital module, has a QPSK AV
converter which simultaneously converts four QPSK modulated channels into AV
signals using two SAT tuners. It is additionally equipped with a common inter-
face, which enables the descrambling of up to 4 scrambled channels through a
single data stream when used in conjunction with a CA module and an appropri-
ate smart card from a service provider.
The
digital
module
has two SAT inputs and one AV interface, through which the
decoded AV signals are fed to the corresponding modulator module. Compo-
nents (e.g. LNB) which are connected upstream can be powered through the
SAT inputs.
The channel strips "A" "B", "C" and "D" can be individually programmed. This
means it is possible to select up to 4 channels from two transponders. Via
tuner "A" scrambled and unscrambled channels can be received. Tuner "D" is
prepared to receive unscrambled channels only.
The following tables show the possible allocations of the selectable number of
channels to the tuners.
For example, if three unscrambled channels from tuner "
A
" will be used, one
unscrambled channel from tuner "
D
" can be used. If , e.g. two unscrambled
channels from tuner "
A
" will be used, two unscrambled channels from tuner
"
D
" can be used.
Tuner "A" Tuner "D"
Quantity of unen-
crypted channels
3 1
2 2
1 3
For example, if four scrambled channels from tuner "
A
" will be used, no chan-
nel from tuner "
D
" can be used. If , e.g. two scrambled channels from tuner
"
A
" will be used, two unscrambled channels from tuner "
D
" can be used.
Tuner "A"
(encrypted
channels)
Tuner "D"
(unencrypted
channels)
Quantity of
channels
4 0
3 1
2 2
1 3
- 6 - CGS 470
Signal transfer principle:
The prepared input signals are fed to the modulator module via the AV in-
terface. From there, they are fed to the HF output collector of the head-end
station, through which the level of the output signal can be adjusted via the
software in the head-end station.
The
digital module
operating software can be updated using a PC or note-
book and the software "BE-Flash" via the 9-pin D-SUB socket on the head-end
station. You can find the current operating software for the
digital module,
the software "BE-Flash"
and the current assembly instructions
on the website
"www.triax.com".
This digital module is designed exclusively for use in the CSE 2800 head-end
station.
Channel strip "A"
Channel strip "B"
Channel strip "C"
Channel strip "D"
CA module
TUNER
"A"
TUNER
"D"
- 7 - CGS 470
3 installation
– Ensure the head-end station is mounted so it will not be able to vibrate.
Avoid, for example, mounting the head-end station onto a lift shaft or any
other wall or floor construction that vibrates in a similar way.
– Before installing or changing a module, switch off the head-end station or
unplug the power cable from the mains power socket.
Take measures to protect against ESD!
•
Open the housing of the head-end station in accordance with the assembly
instructions for the CSE 2800.
3.1 retrofitting a Ca module
The digital module is equipped with a common interface. It allows you to
connect a CA module for various scrambling systems and service providers.
Scrambled channels can only be descrambled with a CA module suitable for
the scrambling system and the corresponding smart card. The smart card con-
tains all the information for authorisation, descrambling and subscription.
Caution
– Check with the distributor or manufacturer of the CA module to be used
to ensure that it is suitable for descrambling several channels.
– The hardware and software of the module CGS 470 have been thoroughly
prepared and tested.
– Any changes made by program providers to the structures in the program
data might impair or even prevent this function.
– When working with a CA module, please read the corresponding operat-
ing manual from the respective provider.
• Insert the smart card
1 into the CA module
2 so that the chip
3
on the
smart card faces the thicker side (top) of the CA module (fig. 1).
• Push the CA module 2 without canting into the guide rails 4 of the com-
mon interface slot 5 according to the following picture and contact it to
the common interface.
- 8 - CGS 470
5
2
3
4
1
3.2 setting the oper ating voltage of the Ca module
The CA modules can require different operating voltages.
• Set the required operating voltage by plugging the jumper to the respective
contacts:
Contacts Operating voltage
1 - 2 + 5 V (Factory default)
3 - 4 + 3.3 V
3
4
1
2
- 9 - CGS 470
3.3 installing the digital module
– If a CA module is used, check that the plug contacts of the CA module are
tightly seated in the terminal strip on the digital module and make sure there
is a reliable contact.
– Always position modules which belong together next to each other. The
digital module must be installed to the left of the modulator module.
– When installing the digital module, make sure that it is inserted in a long
numbered groove in front of a contact strip on the board at the rear wall of
the housing.
The shorter not numbered grooves without a contact strip on the board at
the rear wall of the housing are for add-on modules only.
•
Open the housing of the head-end station in accordance with the assembly
instructions for the CSE 2800.
• Open the locking device 1 in the direction of the arrow.
1
• Insert the digital module in grooves A and B of an open slot left to the
associated modulator module
and gently slide it into the
head-end station
until it makes contact with the board on the rear wall.
A
B
- 10 - CGS 470
• Install the appropriate modulator module.
—> Figure 5 shows the slots 1 (digital module) and 2 (modulator mod-
ule). The slot between them (without a contact strip on the board at
the rear wall of the housing) is for an add-on module only.
E
C
D
1
• After installing the modules close the locking device 1 in direction of the
arrow.
3.4 ConneCting the digital module
• Connect SAT-IF inputs C of the digital module to the preinstalled Ftermi-
nals in the rear wall of the head-end station via the cable inlets E using HF
cables made on-site (length approx. 80 cm) or if applicable to one of the
outputs of a retrofitted SAT-IF input distributor.
• Using the ribbon cable D to connect the AV output of the digital module to
the AV input of the modulator module.
- 11 - CGS 470
4 the Control panel at a glanCe
4.1 menu items
Program the module using the buttons on the head-end station control unit. The
menus appear on the two-line display of the control unit.
The parameters and functions to be set are underlined.
You can use the button to select the following menu items:
– LNB oscillator frequency
– Tuner selection (channel strips "B", "C" and "D" only)
– Symbol rate
– Input frequency
– Station filter
– Audio stream selection
– Audio output level
– Stereo decoding / audio type selection
– Picture format signal (WSS)
– Test lines
– Teletext subtitle page
– Store
4.2 funCtions of the Control panel buttons
S
M
– To move the cursor
– To adjust values and functions
– To store the programmed data
– To switch to the next menu
- 12 - CGS 470
5 programming
5.1 preparation
• Connect the digital module to a programmed modulator module.
—> For the programming of the output channels please read the assem-
bly instructions of the corresponding modulator module.
• Connect the test receiver to the HF output on the modulator module.
• Adjust the test receiver to the output channel of the channel strip to be set:
Digital module – channel strip "A" —> modulator module – channel strip "A",
Digital module – channel strip "B" —> modulator module – channel strip "B",
Digital module – channel strip "C" —> modulator module – channel strip "C",
Digital module – channel strip "D" —> modulator module – channel strip "D".
• Switch on the modulator if necessary. For each modulator, there is a green
LED which indicates if the modulator is switched on.
LED – Channel strip “A“
LED – Channel strip “B“
LED – Channel strip “C“
LED – Channel strip “D“
- 13 - CGS 470
5.2 progr amming proCedure
Bx 1…
10600 MHz
LNB
>
A
Bx 1A
C5-12,S3-24
TWIN-SAT
C07
Böx 4
C5-12,S3-24
TWIN-SAT
C07
Bx 1B
ARD
QUAD
V 18
SETUP
Bx 1A
ARD
QUAD
V 18
V 10
Bx 1A MENU
Information *)
1/6
M
M
/
/
/
/
M
Ein/On
Bx 1…
11836 MHz
FREQ
+0.2
/
/
Bx 1…
Das Erste
01/06 + TV
M
M
Bx 1…
Level
AUDIO
-6 dB
M
Bx 1…
mpeg
AUDIO
DUAL norm
M
M
Bx 1…
01 / 02 “deu”
AUDIO
-26 … 6 dB
Bx 1…
Letter
VIDEO
/
/
/
Bx 1…
27500
SYMBOL
/
/
M
Das Menü wird nur bei Auswahlmöglichkeit
mehrerer Begleittöne angezeigt.
This menu is only displayed if several audio
streams are selectable.
*) Die angezeigte Information ist abhängig
vom verwendeten CA-Modul
The information displayed is dependent on
the CA module used
nur Kanalzug B, C, D
only channel strip B, C, D
nur Kanalzug A und D (INPUT TUNER Line D)
only channel strip A and D (INPUT TUNER Line D)
nur Kanalzug A mit CA-Modul
only channel strip A with CA module
norm / swap
Letter / 16:9
mpeg / VPS
/
/
/
Programmauswahl / Channel selection
M
Bx 1…
txt
SUBTITLE
150 west
Bx 1…
off
SUBTITLE
M
/
/
/
/
/
A
CANCEL
Bx 1…
S => STORE
MEMORY
S
M
M M
Bx 1…
dvb
M
west / east 0…63
off / txt / dvb / black
nur wenn Untertitel
verfügbar sind:
Sprache auswählen
only if subtitles are
available:
select language
SUBTITLE
– –
/
/
Bx 1…
black
SUBTITLE
40/10
M
Bx 1…
TUNER Line A
INPUT
/
TUNER Line D / Line A CA
/
M
Bx 1…
on
TESTLINES
on / off
Bedienhinweise
"blättert" Menüs vorwärts.
wählen die Eingabeposition
wählt Untermenü
stellen Werte ein,.
speichert alle Eingaben.
1 zeigt die Eingabeposition
/
/
M
S
Operating Hints
scrolls forward through the menu.
select the enter position.
selects a submenu.
set values and triggers actions.
saves all entries.
1 shows the enter position
/
/
M
S
Bx 1…
WSS on
VIDEO
TXT on
on / off
/
/
M
BE160
- 14 - CGS 470
Bx 1…
10600 MHz
LNB
>
A
Bx 1A
C5-12,S3-24
TWIN-SAT
C07
Böx 4
C5-12,S3-24
TWIN-SAT
C07
Bx 1B
ARD
QUAD
V 18
SETUP
Bx 1A
ARD
QUAD
V 18
V 10
Bx 1A MENU
Information *)
1/6
M
M
/
/
/
/
M
Ein/On
Bx 1…
11836 MHz
FREQ
+0.2
/
/
Bx 1…
Das Erste
01/06 + TV
M
M
Bx 1…
Level
AUDIO
-6 dB
M
Bx 1…
mpeg
AUDIO
DUAL norm
M
M
Bx 1…
01 / 02 “deu”
AUDIO
-26 … 6 dB
Bx 1…
Letter
VIDEO
/
/
/
Bx 1…
27500
SYMBOL
/
/
M
Das Menü wird nur bei Auswahlmöglichkeit
mehrerer Begleittöne angezeigt.
This menu is only displayed if several audio
streams are selectable.
*) Die angezeigte Information ist abhängig
vom verwendeten CA-Modul
The information displayed is dependent on
the CA module used
nur Kanalzug B, C, D
only channel strip B, C, D
nur Kanalzug A und D (INPUT TUNER Line D)
only channel strip A and D (INPUT TUNER Line D)
nur Kanalzug A mit CA-Modul
only channel strip A with CA module
norm / swap
Letter / 16:9
mpeg / VPS
/
/
/
Programmauswahl / Channel selection
M
Bx 1…
txt
SUBTITLE
150 west
Bx 1…
off
SUBTITLE
M
/
/
/
/
/
A
CANCEL
Bx 1…
S => STORE
MEMORY
S
M
M M
Bx 1…
dvb
M
west / east 0…63
off / txt / dvb / black
nur wenn Untertitel
verfügbar sind:
Sprache auswählen
only if subtitles are
available:
select language
SUBTITLE
– –
/
/
Bx 1…
black
SUBTITLE
40/10
M
Bx 1…
TUNER Line A
INPUT
/
TUNER Line D / Line A CA
/
M
Bx 1…
on
TESTLINES
on / off
Bedienhinweise
"blättert" Menüs vorwärts.
wählen die Eingabeposition
wählt Untermenü
stellen Werte ein,.
speichert alle Eingaben.
1 zeigt die Eingabeposition
/
/
M
S
Operating Hints
scrolls forward through the menu.
select the enter position.
selects a submenu.
set values and triggers actions.
saves all entries.
1 shows the enter position
/
/
M
S
Bx 1…
WSS on
VIDEO
TXT on
on / off
/
/
M
- 15 - CGS 470
5.3 progr amming the digital module
Notes:
– Entries are saved by pressing the button.
—> You will be returned to "Selecting the module/channel strip".
– The programming process can be cancelled by pressing and holding the
button.
—> You will be returned to "Selecting the module/channel strip".
• Switch on the head-end station.
—>
The display shows "SETUP BE160" and the software
version of the
head-end station (e.g. V 10).
—> The output level of the output collector can be adjusted in the "SET-
UP" menu (see CSE 2800 assembly instructions).
SETUP
V 10
Ein/On
BE160
- 16 - CGS 470
seleCting the module / Channel strip
• Press repeatedly if necessary to select the particular module (Bx ...) or
channel strip
"A", "B", "C" or "D"
to be programmed.
Bx 1A
C5-12,S3-24
TWIN-SAT
C07
Böx 4
C5-12,S3-24
TWIN-SAT
C07
Bx 1B
ARD
QUAD
V 18
Bx 1A
ARD
QUAD
V 18
• Press the button to activate the channel strip.
—> The display shows, e.g., the "Bx 1A QUAD" menu.
"Bx" indicates the slot
"1" indicates slot no. 1
"A" indicates channel strip "A"
"ARD" name of the selected channel
"V 18" software version of the module
• Press the button:
Channel strip B, C or D:
—> The "Tuner" – "INPUT TUNER" menu is activated.
Channel strip A:
—> The "LNB oscillator frequency" – "LNB" menu is activated (page 17).
tuner
Select the tuner in this menu out of which demodulated data stream a channel
has to be used.
Bx 1D
TUNER Line A
INPUT
—> This menu is only displayed in channel strips B, C and D.
- 17 - CGS 470
• Using buttons select the tuner:
For Channel strips "B" and "C": "TUNER Line A" or "TUNER Line D",
For Channel strip "D": "TUNER Line D" or "TUNER Line A CA"
• Press the button.
Channel strip A / Channel D with setting "Tuner Line D":
—> The "LNB oscillator frequency" – "LNB" menu is activated.
Channel strip B or C / Channel strip D with setting "Tuner Line A CA":
—> The "Station filter" menu is activated (page 20).
lnb osCillator frequenCy
—> This menu is only displayed in channel strip A / channel strip D with
setting "Tuner Line D".
Bx 1A
10600 MHz
LNB
>
Bx 1A MENU
Information *)
1/6
• Using the
buttons, move the cursor under the digit of the oscillator
frequency to be set.
• Use the
buttons to set the oscillator frequency of the LNB being used
.
• Press the button.
—> This menu is only displayed in channel strip A if a CA modul is in use.
—> The "CA module, card information" – "MENU" is activated.
—> *) The information shown in the display is dependent on the CA
module used.
- 18 - CGS 470
Ca module, Card information
A menu has been provided for these settings, which is displayed on your TV
screen. The menu varies according to which CA module is used. For this rea-
son, please refer to the operating manual of your particular CA module. The
relevant information is shown on the display of the head-end station.
• Use to select a menu item on the screen.
• Activate the menu item with .
• Select the required function with the buttons.
• Press the button to store the settings.
• Press the button.
—> Input symbol rate" – "SYMBOL" menu is activated.
input symbol r ate
—> This menu is only displayed in selection channel strip A and selec-
tion channel strip D with setting "Tuner Line D".
The symbol rate of the satellite transponder can be found in the current trans-
ponder tables of the various satellite
trade magazines or on the website of the
respective service
provider.
Bx 1A
27500
SYMBOL
•
Using the
buttons, move the cursor under the digit of the symbol rate
displayed to be set.
• Use the
buttons to set the desired symbol rate.
• Press the button.
—> The "Input frequency" – "FREQ" menu is activated.
- 19 - CGS 470
input frequenCy
—> This menu is only displayed in selection channel strip A and selec-
tion channel strip D with setting "Tuner Line D".
—> Once the HF receiver has synchronised to the input signal, any
offset to the target frequency is displayed in MHz, e.g. "+ 0.2".
—> If a question mark "?" appears in the second line of the display,
there is no input signal present. Check the configuration of the an-
tenna system and head-end station as well as the preceding settings
of the module in question.
Bx 1A
11836 MHz
FREQ
+0.2
•
Using the
buttons, move the cursor under the digit
of the frequency
displayed
to be set.
• Use the
buttons to set the input frequency.
•
Press the buttons to adjust the input frequency displayed so that the
frequency offset amounts to less than 1MHz.
—>
A status LED indicates the quality of the received transport stream::
Status LED
Tuner ”A“
Status LED
Tuner ”D“
LED indicator Signal quality
Green Good
Orange
Poor
Red no signal
• Press the button.
- 20 - CGS 470
—> The "Station filter" menu is activated.
station filter
In this menu, select the channel from the data stream that is to be made avail-
able through this channel strip.
If the error message "SERVICE no transponder" appears, no input signal
is present. In this case, you should check the previous settings as well as the
configuration of the SAT antenna system.
If the "scanning ..." message appears on the display, the table of received
channels is being read. Please wait until this process is finished.
As soon as the station filter has found all of the TV or radio channels, the corre-
sponding data appears in the display of the
head-end station
.
Bx 1A
Das Erste
01/06 + TV
Meaning of the indicators shown in this example:
"01/06" The first of a total of six channels has been activated.
" + " The audio stream for the current TV channel is avail-
able in several languages.
"TV" The data on the display corresponds to a TV channel.
"Das Erste" Channel name
Other possible indicators:
"RA" The data on the display corresponds to a radio chan-
nel.
" + " The audio stream for the current TV channel is avail-
able in several languages.
" * " A star indicates that this TV or radio channel is scram-
bled. To enable the channels, a CA module and a
s
mart card from the respective service provider
are
required.
—> For radio channels, the background of the screen of the connected
TV or test receiver is darkened.
—> If a service number (e.g. "SERVICE 131") appears instead of "TV" or
"RA", this indicates that an unnamed station or an undefined data
stream is being received.
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28

Triax CGS 470 Assembly Instruction Manual

Triax
Brand
Triax
Model
CGS 470
Type
Assembly Instruction Manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents