BLACK+DECKER AST8XC Owner's manual

Powerful Solutions TM

www.blackanddecker.eu

AST8XC

KS700PE

KS701PE

KS702PE

KS703PE

2

English (Original instructions) 4

Deutsch (Übersetzung der Originalanleitung) 9

Français (Traduction des instructions d'origine) 15

Italiano (Traduzione delle istruzioni originali) 21

Nederlands (Vertaling van de originele instructies) 27

Español (Traducción de las instrucciones originales) 33

Português (Tradução das instruções originais) 39

Svenska (Översättning av de ursprungliga anvisningarna) 45

Norsk (Oversettelse av de opprinnelige instruksjonene) 50

Dansk (Oversættelse af de originale instruktioner) 55

Suomi (Alkuperäisten ohjeiden käännös) 60

Ελληνικά (Μετάφρασητωναρχικώνοδηγιών) 65

Page is loading ...

4

ENGLISH

3. Personal safety

a. Stay alert, watch what you are doing and use common

sense when operating a power tool. Do not use a power

toolwhileyouaretiredorundertheinuenceofdrugs,

alcohol or medication. A moment of inattention while

operating power tools may result in serious personal injury.

b. Use personal protective equipment. Always wear eye

protection. Protective equipment such as dust mask,

non-skid safety shoes, hard hat, or hearing protection

used for appropriate conditions will reduce personal injuries.

c. Prevent unintentional starting. Ensure the switch is in

the off-position before connecting to power source

and/or battery pack, picking up or carrying the tool.

Carrying power tools with your nger on the switch or

energising power tools that have the switch on invites

accidents.

d. Remove any adjusting key or wrench before turning

the power tool on. A wrench or a key left attached to a

rotating part of the power tool may result in personal injury.

e. Do not overreach. Keep proper footing and balance at

all times. This enables better control of the power tool in

unexpected situations.

f. Dress properly. Do not wear loose clothing or

jewellery. Keep your hair, clothing and gloves away

from moving parts. Loose clothes, jewellery or long hair

can be caught in moving parts.

g. If devices are provided for the connection of dust

extraction and collection facilities, ensure these are

connected and properly used. Use of dust collection can

reduce dust-related hazards.

4. Power tool use and care

a. Do not force the power tool. Use the correct power

tool for your application. The correct power tool will do

the job better and safer at the rate for which it was designed.

b. Do not use the power tool if the switch does not turn it

on and off. Any power tool that cannot be controlled with

the switch is dangerous and must be repaired.

c. Disconnect the plug from the power source and/or the

battery pack from the power tool before making any

adjustments, changing accessories, or storing power

tools. Such preventive safety measures reduce the risk of

starting the power tool accidentally.

d. Store idle power tools out of the reach of children and

do not allow persons unfamiliar with the power tool or

these instructions to operate the power tool. Power

tools are dangerous in the hands of untrained users.

e. Maintain power tools. Check for misalignment or

binding of moving parts, breakage of parts and any

other condition that may affect the power tools

operation. If damaged, have the power tool repaired

before use. Many accidents are caused by poorly

maintained power tools.

Intended use

Your Black & Decker jigsaw has been designed for sawing

wood, plastics and sheet metal. This tool is intended for

consumer use only.

Safety instructions

General power tool safety warnings

@

Warning! Read all safety warnings and all

instructions. Failure to follow the warnings and

instructions listed below may result in electric shock,

re and/or serious injury.

Save all warnings and instructions for future reference.

The term "power tool" in all of the warnings listed below refers

to your mains operated (corded) power tool or battery

operated (cordless) power tool.

1. Work area safety

a. Keep work area clean and well lit. Cluttered or dark

areas invite accidents.

b. Do not operate power tools in explosive atmospheres,

suchasinthepresenceofammableliquids,gases

or dust. Power tools create sparks which may ignite the

dust or fumes.

c. Keep children and bystanders away while operating

a power tool. Distractions can cause you to lose control.

2. Electrical safety

a. Power tool plugs must match the outlet. Never modify

the plug in any way. Do not use any adapter plugs

with earthed (grounded) power tools. Unmodied plugs

and matching outlets will reduce risk of electric shock.

b. Avoid body contact with earthed or grounded

surfaces such as pipes, radiators, ranges and

refrigerators. There is an increased risk of electric shock

if your body is earthed or grounded.

c. Do not expose power tools to rain or wet conditions.

Water entering a power tool will increase the risk of

electric shock.

d. Do not abuse the cord. Never use the cord for carrying,

pulling or unplugging the power tool. Keep cord away

from heat, oil, sharp edges or moving parts. Damaged

or entangled cords increase the risk of electric shock.

e. When operating a power tool outdoors, use an

extension cord suitable for outdoor use. Use of a cord

suitable for outdoor use reduces the risk of electric shock.

f. If operating a power tool in a damp location is

unavoidable, use a residual current device (RCD)

protected supply. Use of an RCD reduces the risk of

electric shock.

5

ENGLISH

f. Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges are less

likely to bind and are easier to control.

g. Use the power tool, accessories and tool bits etc.,

in accordance with these instructions, taking into

account the working conditions and the work to be

performed. Use of the power tool for operations different

from those intended could result in a hazardous situation.

5. Service

a. Haveyourpowertoolservicedbyaqualiedrepair

person using only identical replacement parts. This will

ensure that the safety of the power tool is maintained.

Additional power tool safety warnings

@

Warning! Additional safety warnings for jigsaws and

reciprocating saws

u Hold the tool by the insulated gripping surfaces when

performing an operation where the cutting tool may

contact hidden wiring or its own cord. Cutting

accessory contacting a "live" wire may make exposed

metal parts of the power tool "live" and shock the operator.

u Use clamps or another practical way to secure and

support the workpiece to a stable platform. Holding the

work by hand or against your body leaves it unstable and

may lead to loss of control.

u Keep hands away from cutting area. Never reach

underneath the work piece for any reason. Do not insert

ngers or thumb into the vicinity of the reciprocating blade

and blade clamp. Do not stabilize the saw by gripping the

shoe.

u Keep blades sharp. Dull or damaged blades may cause

the saw to swerve or stall under pressure. Always use the

appropriate type of saw blade for the workpiece material

and type of cut.

u When cutting pipe or conduit, make sure that they are free

from water, electrical wiring, etc.

u Do not touch the workpiece or the blade immediately after

operating the tool. They can become very hot.

u Be aware of hidden hazards, before cutting into walls, oors

or ceilings, check for the location of wiring and pipes.

u The blade will continue to move after releasing the switch.

Always switch the tool off and wait for the saw blade to

come to a complete standstill before putting the tool down.

Warning! Contact with, or inhalation of dusts arising from

cutting applications may endanger the health of the operator

and possible bystanders. Wear a dust mask specically

designed for protection against dust and fumes and ensure

that persons within or entering the work area are also

protected.

u This tool is not intended for use by persons (including

children) with reduced physical, sensory or mental

capabilities, or lack of experience and knowledge, unless

they have been given supervision or instruction

concerning use of the appliance by a person responsible

for their safety. Children should be supervised to ensure

that they do not play with the appliance.

u The intended use is described in this instruction manual.

The use of any accessory or attachment or performance

of any operation with this tool other than those

recommended in this instruction manual may present

a risk of personal injury and/or damage to property.

Vibration

The declared vibration emission values stated in the technical

data and the declaration of conformity have been measured in

accordance with a standard test method provided by

EN 60745 and may be used for comparing one tool with

another. The declared vibration emission value may also be

used in a preliminary assessment of exposure.

Warning! The vibration emission value during actual use of

the power tool can differ from the declared value depending

on the ways in which the tool is used. The vibration level may

increase above the level stated.

When assessing vibration exposure to determine safety

measures required by 2002/44/EC to protect persons regularly

using power tools in employment, an estimation of vibration

exposure should consider, the actual conditions of use and the

way the tool is used, including taking account of all parts of the

operating cycle such as the times when the tool is switched off

and when it is running idle in addition to the trigger time.

Labels on tool

The following pictograms are shown on the tool:

:

Warning! To reduce the risk of injury, the user must

read the instruction manual.

Electrical safety

#

This tool is double insulated; therefore no earth wire

is required. Always check that the power supply

corresponds to the voltage on the rating plate.

u If the supply cord is damaged, it must be replaced by the

manufacturer or an authorised Black & Decker Service

Centre in order to avoid a hazard.

6

ENGLISH

Features

This tool includes some or all of the following features:

1. On/off switch

2. Lock-on button

3. Dust extraction outlet

4. Shoe plate

5. Saw blade support roller

6. Pendulum stroke selector

Fig. C

7. Saw blade storage compartment (KS702PE & KS703PE)

Assembly

Warning! Before attempting any of the following operations,

make sure that the tool is switched off and unplugged and that

the saw blade has stopped. Used saw blades may be hot.

Fittingandremovingthesawblade(g.A)

u Loosen (do not remove) the two screws (11).

u Hold the saw blade (8) with the teeth facing forward.

u Insert the shank of the saw blade (8) into the blade holder

(10) as far as it will go.

u Slightly tighten the two screws (11) alternately to position

the blade, then fully tighten the two screws (11).

u To remove the saw blade (8), turn both screws (11) one

turn counter-clockwise.

Connectingavacuumcleanertothetool(g.B)

An adaptor (12) is required to connect a vacuum cleaner or

dust extractor to the tool. The adaptor can be purchased from

your local Black & Decker retailer.

u Push the adaptor (12) into the dust extraction outlet (3).

u Connect the vacuum cleaner hose (13) to the adaptor (12).

Sawbladestorage(KS702PE&KS703PEonly)(g.C)

Saw blades (8) can be stored in the storage compartment (7)

located on the side of the tool

u Open the cover of the saw blade storage compartment (7)

by holding the tab on the top of the door and pulling outwards.

u Remove or store saw blades (8) in the storage

compartment. (7).

u Close the cover of the saw blade storage compartment (7)

and make sure that it is latched closed.

Cutlineblower(g.D)

u To aid visibility when cutting, your jigsaw is equipped with

a cut line blower (14) which will keep the work area clear

of dust as you saw.

Residual risks.

Additional residual risks may arise when using the tool which

may not be included in the enclosed safety warnings. These

risks can arise from misuse, prolonged use etc.

Even with the application of the relevant safety regulations

and the implementation of safety devices, certain residual

risks can not be avoided. These include:

u Injuries caused by touching any rotating/moving

parts.

u Injuries caused when changing any parts, blades or

accessories.

u Injuries caused by prolonged use of a tool. When

using any tool for prolonged periods ensure you take

regular breaks.

u Impairment of hearing.

u Health hazards caused by breathing dust developed

when using your tool (example:- working with wood,

especially oak, beech and MDF.)

Use

Adjustingtheshoeplateforbevelcuts(g.E)

The shoe plate (4) can be set to make either a straight cut or a

left or right bevel cut at an angle of 45°.

u Loosen the screws (9).

u Pull the shoe plate (4) forward, rotate the shoe plate (4) to

the left or right and push it back into the 45° location.

u Tighten the screws (9).

To reset the shoe plate for straight cuts:

u Loosen the screws (9).

u Pull the shoe plate (4) forward, rotate to the centre and

push it back into the 0° location.

u Tighten the screws (9).

Setting the pendulum stroke (g. F)

u Set the pendulum stroke selector (6) to the required

position.

- Position 0: metal and aluminium and sheet metal.

- Position I: for laminates, hard wood, work tops.

- Position II: for plywood and PVC/plastics.

- Position III: for soft wood and fast cutting.

Variable speed control

The tool has a variable speed on/off switch (1). The operating

speed depends on how far you press the switch.

u Use a high speed for wood, medium speed for aluminium

and PVC and low speed for metals other than aluminium.

7

ENGLISH

Switching on and off

u To switch the tool on, press the on/off switch (1).

u To switch the tool off, release the on/off switch (1).

u For continuous operation, press the lock-on button (2) and

release the on/off switch (1).

u To switch the tool off when in continuous operation, press

and release the on/off switch (1).

Sawing

u Hold the tool rmly with both hands while cutting.

u The shoe should be held rmly against the material being

cut. This will help prevent the saw from jumping, reduce

vibration and minimise blade breakage.

u Let the blade run freely for a few seconds before starting

the cut.

u Apply only a gentle pressure to the tool while performing

the cut.

Hints for optimum use

Sawing laminates

When cutting laminates splintering may occur which can

damage the presentation surface. The most common saw

blades cut on the upward stroke, therefore if the shoe plate is

sitting on the presentation surface either use a saw blade that

cuts on the downward stroke or:

u Use a ne-tooth saw blade.

u Saw from the back surface of the workpiece.

u Clamp a piece of scrap wood or hardboard to both sides

of the workpiece to minimise splintering, and saw through

this sandwich.

Sawing metal

u Be aware that sawing metal takes much more time than

sawing wood.

u Use a saw blade suitable for sawing metal.

u When cutting thin sheet metal, clamp a piece of scrap

wood to the back surface of the workpiece and cut through

this sandwich.

u Spread a lm of oil along the intended line of cut.

Maintenance

Your Black & Decker tool has been designed to operate over

a long period of time with a minimum of maintenance.

Continuous satisfactory operation depends upon proper care

and regular cleaning.

Warning! Before performing any maintenance or cleaning,

make sure that the tool is switched off and unplugged and that

the saw blade has stopped.

u Regularly clean the ventilation slots in your tool and

charger using a soft brush or dry cloth.

u Regularly clean the motor housing using a damp cloth.

Do not use any abrasive or solvent-based cleaner.

Never let any liquid get inside the tool and never immerse

any part of the tool into liquid

Mains plug replacement (U.K. & Ireland only)

If a new mains plug needs to be tted:

u Safely dispose of the old plug.

u Connect the brown lead to the live terminal in the new plug.

u Connect the blue lead to the neutral terminal.

Warning! No connection is to be made to the earth terminal.

Follow the tting instructions supplied with good quality plugs.

Recommended fuse: 5 A.

Protecting the environment

Z

Separate collection. This product must not be

disposed of with normal household waste.

Should you nd one day that your Black & Decker product

needs replacement, or if it is of no further use to you, do not

dispose of it with household waste. Make this product

available for separate collection.

z

Separate collection of used products and packaging

allows materials to be recycled and used again.

Re-use of recycled materials helps prevent

environmental pollution and reduces the demand for

raw materials.

Local regulations may provide for separate collection of

electrical products from the household, at municipal waste

sites or by the retailer when you purchase a new product.

Black & Decker provides a facility for the collection and

recycling of Black & Decker products once they have reached

the end of their working life. To take advantage of this service

please return your product to any authorised repair agent who

will collect them on our behalf.

You can check the location of your nearest authorised repair

agent by contacting your local Black & Decker ofce at the

address indicated in this manual. Alternatively, a list of

authorised Black & Decker repair agents and full details of our

after-sales service and contacts are available on the Internet

at: www.2helpU.com

8

ENGLISH

Technical data

AST8XC/KS700PE/KS701PE

KS702PE/KS703PE

Input voltage V

AC

230

Power input W 480

No-load speed min

-1

0-3,000

Max. depth of cut

Wood mm 60

Steel mm 5

Aluminium mm 10

Weight kg 1.9

Level of sound pressure according to EN 60745:

Sound pressure (L

pA

) 86 dB(A), uncertainty (K) 3 dB(A)

Acoustic power (L

WA

) 97 dB(A), uncertainty (K) 3 dB(A)

Vibration total values (triax vector sum) according to EN 60745:

Cutting wood (a

h, CW

) 8.5 m/s

2

, uncertainty (K) 2.4 m/s

2

Cutting metal (a

h, CM

) 9.4 m/s

2

, uncertainty (K) 3.3 m/s

2

EC declaration of conformity

MACHINERY DIRECTIVE

%

AST8XC/KS700PE/KS701PE/KS702PE/KS703PE

Black & Decker declares that these products described under

"technical data" are in compliance with:

98/37/EC (until Dec. 28, 2009), 2006/42/EC

(from Dec. 29, 2009), EN 60745-1, EN 60742-5-11

For more information, please contact Black & Decker at the

following address or refer to the back of the manual.

The undersigned is responsible for compilation of the technical

le and makes this declaration on behalf of Black & Decker.

_

Kevin Hewitt

Vice-President Global Engineering

Black & Decker Europe, 210 Bath Road, Slough,

Berkshire, SL1 3YD

United Kingdom

1-10-2009

Guarantee

Black & Decker is condent of the quality of its products and

offers an outstanding guarantee. This guarantee statement is

in addition to and in no way prejudices your statutory rights.

The guarantee is valid within the territories of the Member

States of the European Union and the European Free Trade

Area.

If a Black & Decker product becomes defective due to faulty

materials, workmanship or lack of conformity, within 24 months

from the date of purchase, Black & Decker guarantees to

replace defective parts, repair products subjected to fair wear

and tear or replace such products to ensure minimum

inconvenience to the customer unless:

u The product has been used for trade, professional or hire

purposes;

u The product has been subjected to misuse or neglect;

u The product has sustained damage through foreign

objects, substances or accidents;

u Repairs have been attempted by persons other than

authorised repair agents or Black & Decker service staff.

To claim on the guarantee, you will need to submit proof of

purchase to the seller or an authorised repair agent. You can

check the location of your nearest authorised repair agent by

contacting your local Black & Decker ofce at the address

indicated in this manual. Alternatively, a list of authorised

Black & Decker repair agents and full details of our after-sales

service and contacts are available on the Internet at:

www.2helpU.com

Please visit our website www.blackanddecker.co.uk to

register your new Black & Decker product and to be kept up to

date on new products and special offers. Further information

on the Black & Decker brand and our range of products is

available at www.blackanddecker.co.uk

Page is loading ...

31

NEDERLANDS

u Voor het zagen van dun plaatmateriaal klemt u een stuk

afvalhout tegen de achterkant van het werkstuk en zaagt u

door deze “sandwich”.

u Smeer een olielm langs de zaagsnede.

Onderhoud

Uw Black & Decker apparaat is ontworpen om gedurende een

lange periode te functioneren met een minimum aan

onderhoud. Voortdurend tevreden gebruik is afhankelijk van

correct onderhoud en regelmatig schoonmaken.

Waarschuwing! Zorg vóór aanvang van onderhoud of

reiniging dat de machine is uitgeschakeld en de netstekker

van het lichtnet is losgekoppeld en dat het zaagblad stil staat.

u Reinig regelmatig de ventilatieopeningen van de machine

en oplader met behulp van een zachte borstel of een

droge doek.

u Reinig regelmatig de behuizing van de motor met een

vochtige doek. Gebruik geen schuur- of oplosmiddel bij

het reinigen. Zorg ervoor dat er geen vloeistof in het

instrument kan komen en dompel geen enkel onderdeel

van de machine ooit onder in vloeistof.

Milieu

Z

Gescheiden inzameling. Dit product mag niet met

het gewone huishoudelijke afval worden weggegooid.

Wanneer uw oude Black & Deckerproduct aan vervanging toe

is of het u niet langer van dienst kan zijn, gooi het dan niet bij

het huishoudelijk afval. Zorg ervoor dat het product

gescheiden kan worden ingezameld.

z

Door gebruikte producten en verpakkingen

gescheiden in te zamelen, worden de materialen

gerecycled en opnieuw gebruikt. Hergebruik van

gerecyclede materialen voorkomt milieuvervuiling en

vermindert de vraag naar grondstoffen.

Inzamelpunten voor gescheiden inzameling van elektrische

huishoudproducten bij gemeentelijke vuilnisbergen of bij de

verkoper waar u een nieuw product koopt, kunnen aan

plaatselijke voorschriften gebonden zijn.

Black & Decker biedt de mogelijkheid tot inzamelen en

recyclen van afgedankte Black & Decker producten.

Om gebruik van deze service te maken, dient u het product

aan een van onze servicecentra te sturen, die voor ons de

inzameling verzorgen.

U kunt het adres van het dichtstbijzijnde servicecentrum

opvragen via de adressen op de achterzijde van deze

handleiding. U kunt ook een lijst van onze servicecentra en

meer informatie m.b.t. onze klantenservice vinden op het

volgende Internet-adres: www.2helpU.com

Technische gegevens

AST8XC/KS700PE/KS701PE

KS702PE/KS703PE

Spanning V

AC

230

Opgenomen vermogen W 480

Onbelast toerental min

-1

0-3.000

Max. freesdiepte

Hout mm 60

Staal mm 5

Aluminium mm 10

Gewicht kg 1,9

Niveau van de geluidsdruk volgens EN 60745:

Geluidsdruk (L

pA

) 86 dB(A), onzekerheid (K) 3 dB(A)

Geluidsvermogen (L

WA

) 97 dB(A), onzekerheid (K) 3 dB(A)

Totale trillingswaarden (triaxale vectorsom) volgens EN 60745:

Zagen van hout

(a

h,CW

) 8.5 m/s

2

, onzekerheid (K) 2.4 m/s

2

Zagen van metaal

(a

h,CM

) 9.4 m/s

2

, onzekerheid (K) 3.3 m/s

2

EG-conformiteitsverklaring

MACHINERICHTLIJN

%

AST8XC/KS700PE/KS701PE/KS702PE/KS703PE

Black & Decker verklaart dat deze producten, zoals onder

"technische gegevens" beschreven, overeenkomstig zijn met:

98/37/EG (tot 28 dec. 2009), 2006/42/EG

(vanaf 29 dec. 2009), EN 60745-1, EN 60745-2-11

Neem voor meer informatie contact op met Black & Decker via

het volgende adres of zie de achterzijde van de handleiding.

De ondergetekende is verantwoordelijk voor de samenstelling

van de technische gegevens en geeft deze verklaring namens

Black & Decker.

_

Kevin Hewitt

Vice-President Global Engineering

Black & Decker Europe, 210 Bath Road, Slough,

Berkshire, SL1 3YD

Verenigd Koninkrijk

1-10-2009

Page is loading ...

38

ESPAÑOL

Declaración de conformidad CE

DIRECTIVA SOBRE MÁQUINAS

%

AST8XC/KS700PE/KS701PE/KS702PE/KS703PE

Black & Decker declara que los productos descritos en

"datos técnicos" son conformes con:

98/37/CE (hasta el 28 de diciembre de 2009), 2006/42/CE

(a partir del 29 de diciembre de 2009), EN 60745-1,

EN 60745-2-11

Si desea información adicional, contacte con Black & Decker

en la siguiente dirección o consulte el dorso de este manual.

El abajormante es responsable de la compilación del archivo

técnico y hace esta declaración en nombre

de Black & Decker.

_

Kevin Hewitt

Vice-President Global Engineering

Black & Decker Europe, 210 Bath Road, Slough,

Berkshire, SL1 3YD

Reino Unido

1-10-2009

Garantía

Black & Decker confía plenamente en la calidad de sus

productos y ofrece una garantía extraordinaria. Esta

declaración de garantía es una añadido, y en ningún caso un

perjuicio para sus derechos estatutarios. La garantía es válida

dentro de los territorios de los Estados Miembros de la Unión

Europea y de los de la Zona Europea de Libre Comercio.

Si un producto Black & Decker resultará defectuoso debido

a materiales o mano de obra defectuosos o a la falta de

conformidad, Black & Decker garantiza, dentro de los

24 meses de la fecha de compra, la sustitución de las piezas

defectuosas, la reparación de los productos sujetos a un

desgaste y rotura razonables o la sustitución de tales

productos para garantizar al cliente el mínimo

de inconvenientes, a menos que:

u El producto haya sido utilizado con propósitos

comerciales, profesionales o de alquiler;

u El producto haya sido sometido a un uso inadecuado

o negligente;

u El producto haya sufrido daños causados por objetos

o sustancias extrañas o accidentes;

u Se hayan realizado reparaciones por parte de personas

que no sean los servicios de reparación autorizados

o personal de servicios de Black & Decker.

Para reclamar en garantía, será necesario que presente

la prueba de compra al vendedor o al servicio técnico de

reparaciones autorizado. Pueden consultar la dirección de su

servicio técnico más cercano poniéndose en contacto con la

ocina local de Black & Decker en la dirección que se indica

en este manual. Como alternativa, se puede consultar en

Internet, en la dirección siguiente, la lista de servicios técnicos

autorizados e información completa de nuestros servicios de

postventa y contactos:

www.2helpU.com

Visite nuestro sitio web www.blackanddecker.eu para

registrar su nuevo producto Black & Decker y mantenerse al

día sobre nuestros productos y ofertas especiales. Encontrará

información adicional sobre la marca Black & Decker

y nuestra gama de productos en www.blackanddecker.eu

Page is loading ...

42

PORTUGUÊS

u Feche a tampa do compartimento de armazenamento (7)

e certique-se de que está fechado com o trinco.

Sopradordelinhadecorte(g.D)

u Para ajudar a visibilidade durante o corte, a serra está

equipada com um soprador de linha de corte (14) que

ajudará a manter a área de trabalho limpa de poeira

enquanto serra.

Riscos residuais.

Podem surgir riscos residuais adicionais durante a utilização

da ferramenta que poderão não constar nos avisos de

segurança incluídos. Estes riscos podem resultar de má

utilização, uso prolongado, etc.

Mesmo com a aplicação dos regulamentos de segurança

relevantes e com a implementação de dispositivos de

segurança, alguns riscos residuais não podem ser evitados.

Incluem:

u ferimentos causados pelo contacto com peças em

rotação/movimento.

u ferimentos causados durante a troca de peças,

lâminas ou acessórios.

u ferimentos causados pela utilização prolongada de

uma ferramenta. Quando utilizar uma ferramenta por

períodos prolongados, faça intervalos regulares.

u diminuição da audição.

u problemas de saúde causados pela inalação de

poeiras resultantes da utilização da ferramenta

(exemplo: trabalhos em madeira, especialmente

carvalho, faia e MDF.)

Utilização

Ajusteabaseparaoscortesembisel(g.E)

Pode regular-se a base (4) tanto para efectuar um corte recto

como um corte em bísel para a esquerda ou para a direita

a um ângulo de 45°.

u Desaperte os parafusos (9).

u Empurre a base (4) para a frente, rode-a (4) para a esquerda

ou para a direita e puxe-a para trás no local a 45°.

u Aperte os parafusos (9).

Para denir a base para cortes rectos:

u Desaperte os parafusos (9).

u Empurre a base para a frente (4), rode para o centro

e puxe-a para trás no local a 0°.

u Aperte os parafusos (9).

Denir o batimento do pêndulo (g. F)

u Coloque o selector do batimento do pêndulo (6) na

posição desejada.

- Posição 0: metal, alumínio e folha de metal.

- Posição I: para laminados, madeira dura, superfícies

de trabalho.

- Posição II: para contraplacado e PVC/plásticos.

- Posição III: para madeira mole e corte rápido.

Controlo de velocidade variável

A ferrramenta tem um interruptor de ligar/desligar

de velocidade variável (1). A velocidade da ferramenta

depende de quanto se prime o interruptor.

u Utiliza uma velocidade elevada para a madeira, uma

velocidade média para alumínio e PVC e uma velocidade

baixa para metais que não o alumínio.

Como ligar e desligar a ferramenta

u Para ligar a ferramenta, prima o interruptor de ligar/

desligar (1).

u Para desligar a ferramenta, liberte o interruptor de ligar/

desligar (1).

u Para um funcionamento contínuo, prima o botão de

bloqueio (2) e liberte o interruptor de ligar/desligar (1).

u Para desligar a ferramenta quando estiver em

funcionamento contínuo, pressione e solte o interruptor

de ligar/desligar (1).

Serrar

u Segure rmemente na ferramente com as duas mãos

enquanto corta.

u Deve segurar-se rmemente a base contra o material a

cortar. Isto ajudará a impedir que a serra salt, a reduzir

a vibração e a minimizar a quebra da lâmina.

u Deixe a lâmina funcionar livremente durante alguns

segundos antes de iniciar o corte.

u Aplique apenas uma leve pressão à ferramenta enquanto

efectua o corte.

Sugestões para uma melhor utilização

Processo de serrar laminados

Ao cortar laminados, pode ocorrer uma formação de rebarbas

que pode danicar a superfície da apresentação. A maior

parte das serras corta de baixo para cima, assim, se a base

repousar na superfície da apresentação, utilize uma serra que

corte de cima para baixo ou:

u Utilize uma lâmina com dentes nos.

u Serre a partir da parte de trás da peça de trabalho.

u Para minimizar as rebarbas, encaixe um bocado de

madeira ou cartão prensado em ambos os lados da peça

de trabalho e serre através desta sanduíche.

Serração de metal

u Tenha em atenção que serrar metal demora mais tempo

do que serrar madeira.

u Utilize uma lâmina adequada para serrar metal.

Page is loading ...

44

PORTUGUÊS

Declaração de conformidade CE

DIRECTIVA MÁQUINAS

%

AST8XC/KS700PE/KS701PE/KS702PE/KS703PE

A Black & Decker declara que os produtos descritos na

secção "dados técnicos" se encontram em conformidade com:

98/37/CE (até 28 de Dezembro de 2009),

2006/42/CE (a partir de 29 de Dezembro de 2009),

EN 60745-1, EN 60745-2-11

Para obter mais informações, queira contactar

a Black & Decker através do endereço que se segue ou

indicado no verso do manual.

O signatário é responsável pela compilação do cheiro

técnico e apresenta esta declaração em nome

da Black & Decker.

_

Kevin Hewitt

Vice-presidente do Departamento de Engenharia Global

Black & Decker Europe, 210 Bath Road, Slough,

Berkshire, SL1 3YD

Reino Unido

1-10-2009

Garantia

A Black & Decker cona na qualidade de seus produtos e

oferece um programa de garantia excelente. Esta declaração

de garantia soma-se aos seus direitos legais e não os prejudica

em nenhum aspecto. A garantia será válida nos territórios dos

Estados Membros da União Europeia e na Área de Livre

Comércio da Europa.

Caso algum produto da Black & Decker apresente avarias

devido a defeitos de material, mão-de-obra ou ausência de

conformidade no prazo de 24 meses a partir da data de

compra, a Black & Decker garantirá a substituição das peças

defeituosas, a reparação dos produtos que foram submetidos

a uso adequado e remoção ou substituição dos mesmos para

assegurar o mínimo de inconvenientes ao cliente a menos

que:

u O produto tenha sido utilizado para ns comerciais,

prossionais ou aluguer;

u O produto tenha sido submetido a uso incorrecto ou

descuido;

u O produto tenha sofrido danos causados por objectos

estranhos, substâncias ou acidentes;

u Tenha um histórico de reparacões efectuadas por

terceiros que não sejam os agentes autorizados ou

prossionais de manutenção da Black & Decker.

Para activar a garantia, será necessário enviar a prova de

compra ao revendedor ou agente de reparação autorizado.

Para vericar a localização do agente de reparação mais

próximo de si contacte o escritório local da Black & Decker no

endereço indicado neste manual. Se preferir, consulte a lista

de agentes autorizados da Black & Decker e os dados

completos de nossos serviços de atendimento pós-venda na

Internet no endereço: www.2helpU.com

Visite o nosso website www.blackanddecker.eu para registar

o seu novo produto Black & Decker e para se manter

actualizado sobre novos produtos e ofertas especiais. Estão

disponíveis mais informações sobre a Black & Decker e sobre

a nossa gama de produtos em www.blackanddecker.eu

Page is loading ...

49

SVENSKA

Tekniska data

AST8XC/KS700PE/KS701PE

KS702PE/KS703PE

Spänning V

AC

230

Ineffekt W 480

Obelastad hastighet min

-1

0-3.000

Max. snittdjup

Trä mm 60

Stål mm 5

Aluminium mm 10

Vikt kg 1,9

Bullernivå,uppmättenligtEN60745:

Bullernivå (L

pA

) 86 dB(A), avvikelse (K) 3 dB(A)

Ljudeffekt (L

WA

) 97 dB(A), avvikelse (K) 3 dB(A)

Vibrationens totala värde (treaxelvektorsumma) bestämd enligt EN 60745:

Såga trä

(a

h,CW

) 8.5 m/s

2

, avvikelse (K) 2.4 m/s

2

Såga i metall

(a

h,CM

) 9.4 m/s

2

, avvikelse (K) 3.3 m/s

2

EC-förklaring om överensstämmelse

MASKINDIREKTIVET

%

AST8XC/KS700PE/KS701PE/KS702PE/KS703PE

Black & Decker deklarerar att dessa produkter, beskrivna

under "tekniska data", är tillverkade i överensstämmelse med:

98/37/EG (till 28 dec. 2009), 2006/42/EG (från 29 dec. 2009),

EN 60745-1, EN 60745-2-11

För mer information, vänligen kontakta Black & Decker på

följande adress eller den som anges på handbokens baksida.

Undertecknad är ansvarig för sammanställningen av den

tekniska len och gör denna försäkran som representant för

Black & Decker.

_

Kevin Hewitt

Vice-President Global Engineering

Black & Decker Europe, 210 Bath Road, Slough,

Berkshire, SL1 3YD

Storbrittannien

1-10-2009

Reservdelar / reparationer

Reservdelar nns att köpa hos auktoriserade Black & Decker

verkstäder, som även ger kostnadsförslag och reparerar våra

produkter.

Förteckning över våra auktoriserade verkstäder nns på

Internet, vår hemsida www.blackanddecker.se samt

www.2helpU.com

Garanti

Black & Decker garanterar att produkten är fri från material-

och/eller fabrikationsfel vid leverans till kund. Garantin är i

tillägg till konsumentens lagliga rättigheter och påverkar inte

dessa. Garantin gäller inom medlemsstaterna i Europeiska

Unionen och i det Europeiska Frihandelsområdet.

Om en Black & Decker produkt går sönder på grund av

material- och/eller fabrikationsfel eller brister i överensstämmelse

med specikationen, inom 24 månader från köpet, åtar sig

Black & Decker att reparera eller byta ut produkten med

minsta besvär för kunden.

Garantin gäller inte för fel som beror på:

u normalt slitage

u felaktig användning eller skötsel

u att produkten skadats av främmande föremål, ämnen eller

genom olyckshändelse

Garantin gäller inte om reparation har utförts av någon annan

än en auktoriserad Black & Decker verkstad.

För att utnyttja garantin skall produkten och inköpskvittot

lämnas till återförsäljaren eller till en auktoriserad verkstad

senast 2 månader efter det att felet har upptäckts. För information

om närmaste auktoriserad verkstad; kontakta det lokala

Black & Decker kontoret på den adress som är angiven

i bruksanvisningen. En lista på alla auktoriserade verkstäder

samt servicevillkor nns även tillgängligt på Internet, adress:

www.2helpU.com

Besök vår webbplats www.blackanddecker.se för att

registrera din nya Black & Decker-produkt samt för att erhålla

information om nya produkter och specialerbjudanden.

Vidare information om märket Black & Decker och vårt

produktsortiment kan åternnas på www.blackanddecker.se

Page is loading ...

52

NORSK

u Hvis strømledningen skades, må den skiftes ut av

fabrikanten eller et autorisert Black & Decker

servicesenter for å unngå fare.

Egenskaper

Dette verktøyet inkluderer noen av eller alle følgende funksjoner:

1. Strømbryter

2. Låseknapp

3. Åpning for støvuttrekk

4. Anleggsplate

5. Støtterulle til sagbladet

6. Pendelslagvelger

Fig. C

7. Sagbladets oppbevaringsrom (KS702PE & KS703PE)

Montering

Advarsel! Før du forsøker noe av følgende, må du passe på

at verktøyet er slått av og koblet fra strømtilførselen, og at

sagbladet har stoppet. Brukte sagblader kan være varme.

Monteringogfjerningavsagbladet(g.A)

u Løsne (uten å fjerne) de to skruene (11).

u Hold sagbladet (8) som vist, med tennene forover.

u Sett skaftet på sagbladet (8) så langt inn i

sagbladholderen (10) som det kommer.

u Trekk lett til de to skruene (11) etter tur for å posisjonere

bladet, og trekk så til skruene (11) fullstendig.

u For å fjerne sagbladet (8), drei begge skruer (11) én

omdreining mot klokken.

Kopletilengrovsuger(g.B)

Det trengs en adapter (12) for å koble en støvsuger eller

grovsuger til verktøyet. Adapteren kan leveres fra din lokale

Black & Decker-forhandler.

u Sett adapteren (12) inn i åpningen for støvuttrekk (3).

u Kople støvsugerslangen (13) til adapteren (12).

Oppbevaring av sagblad

(kunKS702PE&KS703PE)(g.C)

Sagblader (8) kan oppbevares i det spesielle rommet (7) på

siden av verktøyet.

u Åpne dekslet på sagbladrommet (7) ved å holde i iken på

toppen av dekslet og trekke utover.

u Ta ut eller oppbevar sagblader (8) i oppbevaringsrommet. (7).

u Lukk dekslet over sagbladrommet (7) og sørg for at låsen

lukkes.

Sagelinjeblåser(g.D)

u For å hjelpe deg å se når du sager er løvsagen utstyrt

med en sagelinjeblåser (14) som vil holde sageområdet

rent for sagis når du sager.

Andre risikoer.

Ved bruk av verktøyet kan det oppstå ytterligere risikoer som

kanskje ikke er inkludert i sikkerhetsadvarslene som følger

med. Disse risikoene kan bli forårsaket av feil bruk, langvarig

bruk osv.

Selv om de relevante sikkerhetsbestemmelsene blir fulgt, og

sikkerhetstiltakene blir gjennomført, kan visse gjenværende

risikoer ikke unngås. Disse omfatter:

u Personskader som forårsakes av berøring av en

roterende/bevegelig del.

u Personskader som forårsakes av at en del, et blad

eller tilbehør endres.

u Personskader som forårsakes av langvarig bruk av et

verktøy. Når du bruker et verktøy i lange perioder, må

du sørge for å ta regelmessige pauser.

u Svekket hørsel.

u Helsefarer som forårsakes av innånding av støv som

dannes når du bruker verktøyet (eksempel: arbeid

med tre, spesielt eik, bøk og MDF).

Bruk

Justereanleggsplatenforgjæringssaging(g.E)

Denne anleggsplaten (4) kan stilles inn enten til rette kutt eller

et venstre eller høyre gjæringskutt med 45°.

u Løsne skruene (9).

u Trekk anleggsplaten (4) fremover, roter platen til venstre

eller høyre og skyv den tilbake i posisjonen for 45°.

u Stram skruene (9).

Tilbakestille anleggsplaten for rette kutt:

u Løsne skruene (9).

u Trekk anleggsplaten (4) fremover, roter den til senter og

skyv den tilbake i posisjonen for 0°.

u Stram skruene (9).

Innstilling av pendelbevegelsen (g. F)

u Still inn pendelslagvelgeren (6) i ønsket stilling.

- Stilling 0: metall, aluminium og platemetall.

- Posisjon I: for laminater, hardt tre, arbeisater.

- Posisjon II: for nerplater og PVC/plast.

- Posisjon III: for mykt tre og hurtigsaging.

Variabel hastighetskontroll

Verktøyet har en på/av-bryter (1) med variabel hastighet.

Verktøyets hastighet er avhengig av hvor langt inn du trykker

bryteren.

u Bruk høy hastighet til tre, middels hastighet til aluminium

og PVC og lav hastighet for andre metaller enn aluminium.

Start og stopp

u Trykk på strømbryteren (1) for å slå verktøyet på.

u Slipp strømbryteren (1) for å slå verktøyet av.

u For kontinuerlig saging, trykk på låseknappen (2) og slipp

på/av-bryteren (1).

Page is loading ...

54

NORSK

Tekniske data

AST8XC/KS700PE/KS701PE

KS702PE/KS703PE

Spenning V

AC

230

Inn-effekt W 480

Hastighet ubelastet min

-1

0-3.000

Maks. sagedybde

Tre mm 60

Stål mm 5

Aluminium mm 10

Vekt kg 1,9

Lydtrykknivå, målt i samsvar med EN 60745:

Lydtrykk (L

pA

) 86 dB(A), usikkerhet (K) 3 dB(A)

Lydeffekt (L

WA

) 97 dB(A), usikkerhet (K) 3 dB(A)

Totalverdier, vibrasjon (triax vektorsum)i samsvar med EN 60745:

Sage tre

(a

h,CW

) 8.5 m/s

2

, usikkerhet (K) 2.4 m/s

2

Sage metall

(a

h,CM

) 9.4 m/s

2

, usikkerhet (K) 3.3 m/s

2

Samsvarserklæring for EU

MASKINDIREKTIVET

%

AST8XC/KS700PE/KS701PE/KS702PE/KS703PE

Black & Decker erklærer at produktene som beskrives under

"tekniske data" oppfyller kravene til:

98/37/EF (til 28. desember 2009), 2006/42/EF

(fra 29. desember 2009), EN 60745-1, EN 60745-2-11

For mer informasjon, kontakt Black & Decker på følgende

adresse eller se bakerst i håndboken.

Undertegnede er ansvarlig for sammenstillingen av den

tekniske len og avgir denne erklæringen på vegne

av Black & Decker.

_

Kevin Hewitt

Visepresident, Global Engineering

Black & Decker Europe, 210 Bath Road, Slough,

Berkshire, SL1 3YD

Storbritannia

1-10-2009

Reservdeler / reparasjoner

Reservdeler kan kjøpes hos autoriserte Black & Decker

serviceverksteder, som også gir kostnadsoverslag og

reparerer våre produkter.

Oversikt over våre autoriserte serviceverksteder nnes på

Internet, vår hjemmeside www.blackanddecker.no samt

www.2helpU.com

Garanti

Black & Decker garanterer at produktet ikke har material- og/

eller fabrikasjonsfeil ved levering til kunde. Garantien er

i tillegg til kundens lovlige rettigheter og påvirker ikke disse.

Garantien gjelder innen medlemsstatene i den Europeiske

Unionen og i det Europeiske Frihandelsområdet.

Hvis et Black & Decker produkt går i stykker på grunn av

material- og/eller fabrikasjonsfeil eller har mangler i forhold til

spesikasjonene, innen 24 måneder fra kjøpet, påtar

Black & Decker seg å reparere eller bytte ut produktet med

minst mulig vanskelighet for kunden.

Garantien gjelder ikke for feil som kommer av:

u normal slittasje

u feilaktig bruk eller vedlikehold (mislighold)

u at produktet har blitt skadet av fremmede gjenstander,

emner eller ved et uhell

Det gjøres oppmerksom på at produktet ikke er beregnet på

industriell/profesjonell/yrkesmessig bruk, men til hus- og

hjemmebruk.

Garantien gjelder ikke om reparasjoner har blitt utført av noen

andre enn et autorisert Black & Decker serviceverksted.

For å ta garantien i bruk skal produktet og kjøpekvittering

leveres til forhandleren eller til et autorisert serviceverksted

senest 2 måneder etter at feilen har blitt oppdaget.

For informasjon om nærmeste autoriserte serviceverksted;

kontakt det lokale Black & Decker kontoret på den adressen

som er angitt i bruksanvisningen. En oversikt over alle

autoriserte serviceverksteder samt servicevilkår nnes også

tilgjengelig på Internet, adresse: www.2helpU.com

Vennligst stikk innom våre nettsider på www.blackanddecker.no

for å registrere ditt nye Black & Decker-produkt og for å holde

deg oppdatert om nye produkter og spesialtilbud. Du nner

mer informasjon om Black & Decker og produktutvalget vårt

på www.blackanddecker.no

Page is loading ...

ENGLISH

Do not forget to register your product!

www.blackanddecker.co.uk/productregistration

Register your product online at www.blackanddecker.co.uk/productregistration or send your name, surname and product

code to Black & Decker in your country.

DEUTSCH

Vergessen Sie nicht, Ihr Produkt registrieren zu lassen!

www.blackanddecker.de/productregistration

Lassen Sie Ihr Produkt unter www.blackanddecker.de/productregistration online registrieren oder schicken Sie Ihren

Nachnamen, Vornamen und den Produktcode an Black & Decker in Ihrem Land.

FRANÇAIS

N’oubliez pas d’enregistrer votre produit !

www.blackanddecker.fr/productregistration

Enregistrez votre produit en ligne sur www.blackanddecker.fr/productregistration ou envoyez vos nom, prénom et code

produit à Black & Decker dans votre pays.

ITALIANO

Non dimenticate di registrare il prodotto!

www.blackanddecker.it/productregistration

Registrate il prodotto online su www.blackanddecker.it/productregistration o inviate nome, cognome e codice del prodotto al

centro Black & Decker del vostro paese.

NEDERLANDS

Vergeet niet uw product te registreren!

www.blackanddecker.nl/productregistration

U kunt uw product online registreren op www.blackanddecker.nl/productregistration of u kunt uw voornaam, achternaam en

productcode opsturen naar Black & Decker in uw land.

ESPAÑOL

¡No olvide registrar su producto!

www.blackanddecker.es/productregistration

Registre su producto on-line en www.blackanddecker.es/productregistration o envíe su nombre, apellidos y código de

producto a Black & Decker en su país.

PORTUGUÊS

Não se esqueça de registar o seu produto!

www.blackanddecker.pt/productregistration

Registe o seu produto online em www.blackanddecker.pt/productregistration ou envie o seu nome, apelido e código do

produto para a Black & Decker no seu país.

SVENSKA

Glöm inte att registrera produkten!

www.blackanddecker.se/productregistration

Registrera produkten online på www.blackanddecker.se/productregistration eller skicka namn och produktkod till

Black & Decker i landet du bor i.

NORSK

Ikke glem å registrere produktet ditt!

www.blackanddecker.no/productregistration

Registrer produktet ditt online på www.blackanddecker.no/productregistration, eller send ditt navn, etternavn og produktkode

til Black & Decker i ditt eget land.

DANSK

Glem ikke at registrere dit produkt!

www.blackanddecker.dk/productregistration

Registrer dit produkt på internettet på: www.blackanddecker.dk/productregistration eller send dit navn, efternavn og

produktkode til Black & Decker i dit eget land.

SUOMI

Muistathan rekisteröidä tuotteesi!

www.blackanddecker./productregistration

Rekisteröi tuotteesi verkossa osoitteessa www.blackanddecker./productregistration tai lähetä etunimesi, sukunimesi ja

tuotekoodi oman maasi Black & Decker -edustajalle.

ΕΛΛΗΝΙΚΑ

Μηνξεχάσετενακαταχωρίσετετοπροϊόνσας!

www.blackanddecker.gr/productregistration

Καταχωρίστε το προϊόν σας σε σύνδεση στη σελίδα www.blackanddecker.gr/productregistration ή στείλτε το όνομα, επίθετο

σας και τον κωδικό πριονωτός στη Black & Decker στη χώρα σας.

België/Belgique Black & Decker (Belgium) N.V. Tel. 016 68 91 00

Nieuwlandlaan 7 Fax 016 68 91 11

I.Z. Aarschot B156

3200 Aarschot

Danmark Black & Decker Tel. 70 20 15 10

Sluseholmen 2-4, 2450 København SV Fax 70 22 49 10

Internet: www.blackanddecker.dk

Deutschland Black & Decker GmbH Tel. 06126/21 - 0

Black & Decker Str. 40, D - 65510 Idstein Fax 06126/21 29 80

Ελλάδα Black & Decker (Ελλάς) Α.E. Τηλ. 210 8981616

Στράβωνος 7 & Λεωφ. Βουλιαγμένης 159 Φαξ 210 8983285

166 74 Гλυφάδα - Αθήνα www.blackanddecker.eu

España Black & Decker Ibérica, S.C.A. Tel. 934 797 400

Parc de Negocis “Mas Blau” Fax 934 797 419

Edicio Muntadas, c/Bergadá, 1, Of. A6

08820 El Prat de Llobregat (Barcelona)

France Black & Decker (France) S.A.S. Tel. 04 72 20 39 20

5 allée des Hêtres Fax 04 72 20 39 00

B.P. 30084

69579 Limonest Cédex

Helvetia ROFO AG Tel. 026-6749391

Gewerbezone Seeblick Fax 026-6749394

3213 Kleinbösingen

Italia Black & Decker Italia SpA Tel. 039-23871

Viale Elvezia 2 Fax 039-2387592/2387594

20052 Monza (MI) Numero verde 800-213935

Nederland Black & Decker Benelux Tel. 0164 - 283000

Joulehof 12, 4622 RG Bergen op Zoom Fax 0164 - 283100

Norge Black & Decker (Norge) A/S Tlf. 22 90 99 00

Postboks 4814, Nydalen, 0422 Oslo Fax 22 90 99 01

Internet: www.blackanddecker.no

Österreich Black & Decker Vertriebsges.m.b.H Tel. 01 66116-0

Oberlaaerstraße 246, A1100 Wien Fax 01 66116-14

Portugal Black & Decker Tel. 214667500

Rua Egas Moniz 173 Fax 214667580

S. João do Estoril

2766-651 Estoril

Suomi Black & Decker Oy Puh. 010 400 430

Keilasatama 3, 02150 Espoo Faksi (09) 2510 7100

Black & Decker Oy, Tel. 010 400 430

Kägelhamnen 3, 02150 Esbo Fax (09) 2510 7100

Sverige Black & Decker AB Tel. 031-68 60 60

Box 94, 431 22 Mölndal Fax 031-68 60 80

United Kingdom Black & Decker Tel. 01753 511234

210 Bath Road Fax 01753 551155

Slough, Berkshire SL1 3YD Helpline 01753 574277

Middle East & Africa Black & Decker (Overseas) A.G. Tel. +971 4 2826464

PB 5420, Dubai, United Arab Emirates Fax +971 4 2826466

90557365 REV-0 10/2009

BLACK+DECKER AST8XC Owner's manual

BLACK+DECKER AST8XC Owner's manual

in other languages

Related papers

Other documents