Premier GEN-3304 User manual

Brand: Premier

Model: GEN-3304

Category: Power generators

Type: User manual

This manual is also suitable for

INSTRUCTION MANUAL

GASOLINE GENERATOR

GEN-3300, GEN-3301, GEN-3302,

GEN-3303, GEN-3304, GEN-3305

DEAR CUSTOMER

Congratulations for your purchase!

Please read this manual carefully and keep it for future reference.

If you need additional support please write to: [email protected]

P-1

CAUTION

RISK OF ELECTRIC

SHOCK, DO NOT

OPEN

Caution: To reduce the risk of electric shock do not open

this device, there are not serviceable parts for customers.

Please refer any maintenance or repair to qualified

personnel.

This sign means the existence of dangerous voltage at

the inside of the unit, which states a risk of electric shock.

This sign means that there are important instructions of

operation and handling in the manual that comes with this

device.

PREMIER CUSTOMER SERVICE

Venezuela:

0800 – ELECTRIC (353-2874)

Colombia:

01-900-331-PEJC (7352)

Panama:

300-5185

Website:

www.premiermundo.com

E-mail:

[email protected]

NOTE

This unit may be submitted to changes in specifications, characteristics and/or operation without prior

notice to the user, in order to continue improving and developing its technology.

INTRODUCTION

In order to achieve the best performance of your generator please read this instruction manual carefully

before using it.

P-2

SAFETY INFORMATION

EXHAUST FUMES ARE POISONOUS

z Never operate the engine closed or it may cause unconsciousness and death within a short time.

Operate the engine in a well ventilated area.

FUEL IS HIGHLY FLAMMABLE AND POISONOUS

z Always turn off the engine when refueling.

z Never refuel while smoking or in the vicinity of an open flame.

z Take care not to spill any fuel on the engine or muffler when refueling.

z If you allow any fuel, inhale fuel vapor, or allow any to get in your eyes, see your doctor immediately.

If any fuel spills on your skin or clothing, immediately wash with soap and water, and change your

clothes.

z When operating or transporting the machine, be sure it is kept upright if it tilts, fuel may leak from the

carburetor or fuel tank.

ENGINE AND MUFFLER MAY BE HOT

z Place the machine in a place where pedestrians or children are not likely to touch the machine.

z Avoid placing any flammable materials near the exhaust outlet during operation.

z Keep the machine at least 1 m (3 ft) from building or other equipment, or the engine may overheat.

z Avoid operating the engine with a dust cover

ELECTRIC SHOCK PREVENTION

z Never operate the engine in rain or snow.

z Never touch the machine with wet hands or electrical shock will occur.

z Be sure to ground (earth) the generator.

NOTE

z Use ground (earth) lead of sufficient current capacity.

z Ground (earth) Lead

Diameter.0.12mm (0.055in)/ampere

EX: 10 Ampere-1.2mm (0.055in)

CONNECTION NOTES

z Avoid connecting the generator to commercial power outlet.

z Avoid connecting the generator in parallel with any other generator.

BATTERY

z No smoking while handing the battery.

z The battery emits flammable hydrogen gas, which can explode if exposed to electric arcing or open

flame.

z Keep the area well-ventilated and keep open flames/sparks away when handing the battery.

P-3

CONTROL FUNCTION

OIL WARNING SYSTEM

When the oil level falls below the lower level, the engine stops automatically.

Unless you refill with oil, the engine will not start again.

ENGINE SWITCH

The engine switch is controlled by the ignition system.

1. “ON” (run)

Ignition circuit is switched on.

The engine can be started.

2. “OFF” (stop)

Ignition circuit is switched off.

The engine will not run.

3. “START”

Starting circuit is switched on.

The starter motor starts.

AC SWITCH (N.F.B)

The AC switch turns off automatically when the load exceeds the generator rated output.

NOTE

Reduce the load to within specified generator rated output if the AC switch (N.F.B) turns off.

P-4

DESCRIPTION

1. Fuel tank

2. Fuel tank cap

3. Fuel cock

4. Air filter cover

5. Spark plug

6. Muffler

7. Choke lever

15. Oil warning light

16. AC switch (N.F.B)

17. Voltmeter

18. DC socket (optional)

19. DC circuit breaker (optional)

20. AC output select SW (optional)

21. Pilot light

8. AC socket

9. Engine switch

10. Ground (earth) terminal

11. Oil filter gap

12. Oil drain plug

13. Recoil starter

14. Fuel level gauge

P-5

PRE-OPERATION CHECK

NOTE

Pre-operation checks should be made each time the generator is used.

CHECK ENGINE FUEL

z Check fuel level at fuel level gauge.

z If fuel level is low, refill with unleaded automotive gasoline.

z Be sure to use fuel filter screen on the fuel filter neck.

z Recommend fuel: Unleaded gasoline.

z Fuel tank capacity:

Model Full

GEN-3300, GEN-3302 6.3L

GEN- 3301 13L

GEN-3303, GEN-3304, GEN-3305 25L

NOTE

z Do not refill tank while engine is running or hot.

z Close fuel cock before refueling with fuel.

z Be careful not to admit dust, dirt, water or other foreign objects into fuel.

z Wipe off spilt fuel thoroughly before starting engine.

z Keep open flames away.

z “F”Full,”E”Empty.

CHECK ENGINE OIL

Before checking or refilling oil, be sure the generator is put on a stable and level surface with engine

stopped.

z Remove oil filler cap and check the engine oil level.

z If oil level is below the lower level line, refill with suitable oil to upper level line. Do not screw in the oil

filler cap when checking oil level.

z Change oil if contaminated.

z Oil capacity

Model Full

GEN-3300, GEN-3302 0.37L

GEN- 3301 0.6L

GEN-3303, GEN-3304, GEN-3305 1.1L

z Recommend engine oil:

APL service "SE” or "SF”, if not available, "SD”

GROUND (Earth)

Make sure to ground (earth) the generator.

P-6

OPERATION

NOTE

The generator has been shipped without engine oil. Fill with oil otherwise it will not start.

STARTING THE ENGINE

NOTE

z Before starting the engine, do not connect the electric apparatus.

z Turn the AC switch(N.F.B)to “OFF”

1. Turn the fuel cock lever to “ON”

2. Turn the engine switch to “ON”

3. Turn the choke lever to the” choke “position. Not necessary if the

engine is warm.

4. Pull the starter handle slowly until resistance is felt. This is the

"Compression” point. Return the handle to its original position and

pull swiftly. Do not fully pull out the rope. After starting, allow the

starter handle to return to its original position while still holding the

handle.

5. Warm up the engine.

6. Turn the choke lever back to the operating position.

7. Warm up the engine without a load for a few minutes.

USING ELECTRIC POWER

AC APPLICATION (SINGLE VOLTAGE TYPE)

1. Check the voltmeter or pilot lamp for proper voltage.

2. Turn off the switch (es) of the electrical appliance(s).

3. Insert the plug(s) of the electrical appliance(s) into the receptacle.

4. Turn the AC switch to the "ON” position and turn on the electric apparatus.

NOTE

z Be sure the electric apparatus is turned off before plugging in.

z Be sure the total load is within generator rated output.

z Be sure the socket load current is within socket rated current.

z To take out power from TWIST LOCK receptacle, insert the plug into receptacle and turn clockwise

to lock it.

AC APPLICATION (DUAL VOLTAGE TYPE)

1. Select the voltage using the AC OUTPUT SELECT SWITCH in accordance

with the electrical appliance.

2. Operate in the same way as step (1) through step (4) of single voltage type.

NOTE

Voltmeter always indicates the lower voltage whichever the AC OUTPUT SELECT SWITCH is set.

P-7

DC APPLICATION (option)

This usage is applicable to 12V battery charging only.

Charging instruction for battery

1. Disconnect the leads for the battery.

2. Make the battery fluid filler cap loose fully.

3. Fill distilled water to the upper limit, if the battery fluid is low

level.

4. Measure the specific gravity for the battery fluid by using the

hydrometer, and calculate the charging time in according with

the table shown on right side.

5. The specific gravity for the fully charged battery shall be within

1.26 to1.28. It is recommended to confirm every hour.

6. Connect between the DC output socket and the battery

terminals using the charging leads. The leads shall be

connected making sure of the (+) and (-) polarity.

7. The DC circuit protector is to be set to “ON” after confirming the

connection, if the protector is in "OFF” position.

STOPPING THE ENGINE

1. Turn off the power switch of the electric apparatus or unplug the cord from receptacle of the

generator. Turn the AC switch to “OFF”.

2...Turn the engine switch to “OFF”

3. Turn the fuel cock lever to “OFF”.

4. Complete burning the oil inside the carburetor when you won’t use the generator in a long time.

BATTERY

(For electric starting system)

REPLENISHING THE BATTERY FLUID (only for acid battery)

z Check the fluid level. The level should be between the upper and lower level marks.

z Add only distilled water if necessary.

BATTERY STORE

z Remove the battery and charge it.

z Store it in a dry place and recharge it once a month.

z Do not store the battery in an excessively warm or cold place.

RECOMMENDED BATTERY

z Recommended battery:12V17Ah(GEN-3303,GEN-3304,GEN-3305)

12V/6.5Ah (GEN-3301)

NOTE

z Clamp the red wire to the positive (+) terminal and the black wire to the negative (-) terminal of the

battery. Do not reverse these positions.

z Be sure the battery is installed on the battery mount tray securely.

z In order to increase the longevity of your generator. It is advantageous to maintain a minimum load

of approximately one third the rated output.

P-8

PERIODIC MAINTENANCE

MAINTENANCE CHART

P-9

ENGINE OIL REPLACEMENT

1. Place the machine on a level surface and warm up the engine for several minutes. Then stop the

engine.

2. Remove the oil filler cap

3. Place an oil pan under the engine. Remove the oil drain plug so that the oil

can be completely drained.

4. Check the oil drain plug, gasket, oil filler cap and O-ring. If damaged, please

replace.

5. Reinstall the oil drain plug.

6. Add engine oil to the upper level.

z Recommended engine oil:

APL Service "SE” or "SF”, if not available, "SD”.

NOTE

Be sure no foreign material enters the crankcase.

AIR FILTER

Maintaining an air cleaner in proper condition is very important. Dirt induced

through improperly installed, improperly serviced, or inadequate elements damages

and wears out engines. Keep the element always clean.

1. Take out the air cleaner, clean it well in kerosene and dry it.

2. After wetting the element by clean engine oil, squeeze it tightly by hand.

3. Lastly, put the element in the case and install it securely.

NOTE

The engine should never run without the element, excessive piston and/or cylinder

wear may result.

SPARK PLUG

1. Cleaning and adjusting spark

plug

2. Standard Spark Plug:

F7TC/LD

FUEL COCK

1. Stop the engine.

2. Turn the fuel cock lever to

“OFF”

3. Clean with solvent.

4. Wipe off.

5. Check the gasket, replace it if

damaged.

NOTE

Be sure the fuel cock cup is tightened securely.

P-10

FUEL TANK FILTER

1. Clean with solvent

2. Wipe off.

3. Fuel tank filter.

NOTE

Be sure tank cap is tightened securely.

MUFFLER SCREEN

1. Remove the muffler protector and muffler screen.

2. Clean the carbon deposits out of the muffler screen using a wire brush,

3. Check the muffler screen, Replace it if damaged.

4. Install the muffler screen and muffler protector.

 Muffler protector

 Muffler screen

NOTE

z The engine and muffler will be very hot after the engine has been run.

z Avoid touching the engine and muffler while they are still hot with any part of your body or clothing

inspection of repair.

STORAGE

Long term storage of your machine will require some preventive procedures to guard

DRAIN THE FUEL

1. Drain the fuel tank, fuel dockhand carburetor float bowl.

2. A cup of SAE 10W30 or 20W40 motor oil.

3. Shake the tank.

4. Drain off the excess oil.

ENGINE

1. Pour in about one tablespoon of SAE 10W30 or 20W40 motor oil.

2. Use the recoil starter to turn the engine over several times (with ignition off).

3. Pull the recoil starter until you feel compression.

4. Stop pulling.

5. Clean exterior of the generator and apply a rust inhibitor.

6. Store the generator in a dry, well-ventilated place, with the cover place over it.

7. The generator must remain in a vertical position.

P-11

SPECIFICATION

Model GEN-3300/3302 GEN-3301 GEN-3303 GEN-3304 GEN-3305

Generator

Type

Brushless, self-

exciting,

2 Poles, Single-

Phase

Brush, self-exciting, 2 Poles, Single-Phase, AVR

Rate AC

Output

0.85KW/1.0KW 2.0KW 3.5KW 4.5KW 4.5KW

Max AC

Output

1KW/1.1KW 2.1KW 3.8KW 5.0KW 5.0KW

Horse Power

2.4HP 5.5HP 9HP 13HP 13HP

Frequency

60Hz

Voltage

110V

Power Factor

CosΦ=1.0

DC Output

12V/8.3A(option)

Engine

Model

154F 163F 177F 188F 188F

Type

Air-cooled;4-stroke;OHV250tilt,level shaft,1- cylinder

Displacement

87cm

163 cm

270cm

389cm

389 cm

Max.Output

2.4hp/3600rpm 5.5 hp/3600rpm 9 hp/3600rpm

hp/3600rpm

Ignition

System

TCI

Fuel

Unleaded Gasoline

Fuel tank

capacity

6L 15L 25L

Engine Oil

Capacity

0.37L 0.6L 1.1L

Start Mode

Recoil Recoil/ Electric start

Set

Cont.working

time

9h 13h 13h 12h 10h

Noise

level(7m)

85dB 87 dB 85 dB 85 dB 85dB

Packing

Dimension

LxWxH

460x370x385mm 610x450x460mm

700x540x570mm

Net Weight

26kg 38kg 74kg 78 kg 78kg

Premier GEN-3304 User manual

Brand: Premier

Model: GEN-3304

Category: Power generators

Type: User manual

This manual is also suitable for

Download PDF

report

Premier GEN-3304 User manual

This manual is also suitable for

Premier GEN-3304 User manual

Related papers

Other documents