American Dynamics AD615 Quick Reference Manual

Brand
American Dynamics
Model
AD615
Type
Quick Reference Manual

This manual is also suitable for

DeltaDome™ Programmable Surveillance Camera
Configuration Utility Quick Reference Guide
8000-2613-02, Rev. B Quick Reference Guide
This Quick Reference Guide illustrates the screens found in the
DeltaDome Programmable Surveillance Camera Configuration
Utility. The large numbers in the circles represent the number of
the screen. The small numbers appearing to the right of the menu
choices represent the screen you will see if you pick that choice.
Note
: The numbers in the circles do not actually appear on the
screens.
To start the configuration utility, do one of the following:
• For SensorNet or RS-422, press and hold Iris Open, press and
hold a Focus button, then press Zoom Out.
• For Manchester, turn the key switch to Prog (or disable the
system lock on the T
OUCH
T
RACKER
®
), use the keypad to enter
66, then press Set Preset..
Refer to the keyboard or T
OUCH
T
RACKER
operating instructions
for the locations of the control buttons.
DOME CONFIGURATION MENU
PAN/TILT/ZOOM OPTIONS
CAMERA / LENS FUNCTIONS
ALARMS / AREAS / HOME
ON-SCREEN TEXT DISPLAY
LANGUAGE / PASSWORD
EXIT AND SAVE CHANGES
QUIT WITHOUT SAVING
RESET TO FACTORY SETTINGS
1
2
3
4
5
6
NOTE
: If password protection is enabled, you must enter the
password before the Dome Configuration Menu will display.
Refer to screen
19
for information.
The following table describes the functions of the controls used
to interact with the screens. Where a specific Focus button is not
specified, either the Focus Near or Focus Far button may be used.
Function Control
Display configuration menu (SensorNet and RS-422
only)
Iris Open, Focus,
then Zoom Out
Display configuration menu (Manchester only)
Key switch to Prog,
66, then Set Preset
Save and exit utility from any screen (not supported
on Manchester)
Iris Close then
Focus
Moves highlight bar up
Tilt Up
Moves highlight bar down
Tilt Down
Moves highlight bar right
Pan Right
Moves highlight bar left
Pan Left
Selects the highlighted item
Focus Far
Increases the value or displays the next choice
During naming, moves the cursor to the right of the
current character in the name
Zoom In
(Zoom Tele)
Decreases the value or displays the previous choice
During naming, moves the cursor to the left of the
current character in the name
Zoom Out
(Zoom Wide)
PAN / TILT / ZOOM OPTIONS
PROPORTIONAL FLIP
OFF
1ST ZOOM STOP X 24
MAX TOTAL ZOOM X 128
EXIT
RESET TO FACTORY SETTINGS
2
1
Settings (Defaults in Bold)
Proportional Flip
ON
/ OFF
1st Zoom Stop X 16 / 24
Max Total Zoom X 32 / 48 / 64 / 80 / 96 / 112 / 128
CAMERA / LENS FUNCTIONS
LINE LOCK
OFF
AGC MODE
ON
AGC GAIN
112
EXIT
RESET TO FACTORY SETTINGS
AUTO WHITE BAL
ON
RED WHITE BAL
457
BLUE WHITE BAL
563
3
1
Settings (Defaults in Bold)
Line Lock
ON
/ OFF
AGC Mode
ON
/ OFF
AGC Manual Gain: 0 - 1128*
Auto White Bal
ON
/OFF
Red White Bal 128-1023**
Blue White Bal 128-1023**
* AGC Mode must be
OFF
to change
** Auto White Bal must be
OFF
to change
2 8000-2613-02, Rev. B Quick Reference Guide
ALARMS / AREAS / HOME
SET ALARM ACTIONS
CONFIGURE NORMAL STATES
CONFIGURE HOME POSITION
EXIT
PROGRAM AREA BOUNDARIES
PROGRAM PRESETS
4
1
7
8
9
10
11
Select an item, then press
Focus Far
to make the changes.
Alarm inputs and outputs are not supported for Manchester.
ON-SCREEN TEXT DISPLAY
STATUS DISPLAY
OFF
EXIT
DISABLE ALL NAMES? NO
NAME CONFIGURATION MENU
TEXT ATTRIBUTE OPTIONS
DIAGNOSTICS DISPLAY
ON
5
1
13
16
Settings (Defaults in Bold)
Status Display ON /
OFF
Disable All Names? YES /
NO
Diagnostic Display ON /
OFF
LANGUAGE / PASSWORD
LANGUAGE SELECTION
EXIT
SET PASSWORD
PASSWORD PROTECTION
OFF
6
1
17
18
Press
Focus Far
to display Language Selection (screen 17) or Set
Password (screen 18).
Settings (Defaults in Bold)
Password Protection ON /
OFF
SET ALARM ACTIONS
EXIT
INPUT NO.
ACTION
SEND INPUTS TO HOST? YES
NO ACTION
1
PRESET 96
2
PATTERN 33
NO ACTION4
INTERNAL ALARMS
7
4
Settings (Defaults in Bold)
Input 1 - 4 Actions
NO ACTION
/ PRESET / PATTERN
Send Inputs to Host?
YES
/ NO
Preset Number 1-96; Pattern Number 1-3
Note
: Do not assign input action on both dome and controller.
8000-2613-02, Rev. B
3
CONFIGURE NORMAL STATES
EXIT
INPUT NO.
NORMAL STATE
OPEN1
OPEN
2
CLOSED3
OPEN4
8
4
Settings (Defaults in Bold)
Input 1 - 4 Normal State
OPEN
/ CLOSED
Note
: Do not assign input action on both dome and controller.
CONFIGURE HOME POSITION
EXIT
HOME POSITION
PRESET 96
10
RETURN TIME MINS
9
4
Settings (Defaults in Bold)
Return to Home Position
NO ACTION
/ PRESET/ PATTERN
Return Time Mins 1 - 60 (Default is
10
minutes)
Preset Number 1-96; Pattern Number 1-3
PROGRAM AREA BOUNDARIES
ZOOM to mark BOUNDARY
PAN to start of BOUND
3
PAN RIGHT ONLY
FOCUS saves and exits
10
•
Up to 16 areas can be programmed.
•
Press
Zoom In
or
Zoom Out
to set area boundary
•
Press
Focus Far
when finished setting areas
SELECT PRESET TO PROGRAM
EXIT
PRESET NAME
PRESET
NUMBER
PRESET 9696
FOCUS FAR to program preset
11
4
12
•
Use
Zoom In
or
Zoom Out
choose the correct preset number.
•
Press
Focus Far
to perform preset programming.
12
PROGRAM PRESET
PRESET 1
EXIT
Position camera with PAN,
TILT, ZOOM, and IRIS
FOCUS FAR to save and exit
This screen appears under two circumstances:
•
By selecting a preset number and pressing
Focus Far
on the
Select
Preset To Program
screen (see screen
11
).
•
By selecting a preset that has not been programmed as the
Home
Position
(see screen
9
).
Use
Pan
,
Tilt
,
Zoom
, and
Iris
controls to set the view for the preset.
Press
Focus
Far
when finished.
Press Focus Far
twice to return to
screen 4.
If Preset is selected and
no preset exists, you will
see screen 12.
11 or 4
4 8000-2613-02, Rev. B Quick Reference Guide
NAME CONFIGURATION MENU
OFF
CAMERA NAME
OFFAREA NAME
OFFPRESET NAME
OFFPATTERN NAME
ON
ALARM NAME
FOCUS FAR to program name
13
EXIT
5
15
14
RESET PROGRAMMABLE NAMES
Settings (Defaults in Bold)
Camera Name ON /
OFF
Area Name ON /
OFF
Preset Name ON /
OFF
Pattern Name ON /
OFF
Alarm Name
ON
/ OFF
•
Use
Zoom In
or
Zoom Out
to change setting for highlighted item.
•
Press
Focus Far
to perform name programming for highlighted item.
In this example, Camera Naming would be started.
SELECT NAME TO PROGRAM
EXIT
CURRENT NAME
PATTERN
NUMBER
FOCUS FAR to program names
14
13
15
PATTERN 11
Example Select Name to Program Screen (for Patterns)
•
Use
Zoom In
or
Zoom Out
choose the correct area, preset, pattern or
alarm number.
•
Dome moves to start of specified area, preset, or pattern (if
programmed)
•
Press
Focus Far
to display Name Programming Screen
Available Settings:
Area Number 1-16
Preset Number 1-96
Pattern Number 1-3
Alarm Number: 1-4
NAME PROGRAMMING
PATTERN 1
NAME: PATTERN 1. . . . . . . . . .
EXIT
UNDO CHANGES AND QUIT
15
A B C D E F G H I J K L M N O P Q R S T
U V W X Y Z a b c d e f g h i j k l m n
o p q r s t u v w x y z 0 1 2 3 4 5 6
7 8 9 / -
Example Name Programming Screen (for Patterns)
•
Names can have up to 19 characters
•
Use
Zoom In
to move cursor one space to right in
Name
•
Use
Zoom Out
to move cursor one space to left in
Name
•
Use
Pan
and
Tilt
to move highlight around character field
•
Press
Focus Far
to accept highlighted character
•
The
SPACE
character is located between
z
and
0 (zero)
TEXT ATTRIBUTE OPTIONS
CHARACTER OUTLINE
OFF
EXIT
TRANSLUCENT NAMES
OFF
16
5
Settings (Defaults in Bold)
Character Outline
ON
/ OFF
Translucent Names
ON
/ OFF
13 or 14
13 or 14
Blank
Space
8000-2613-02, Rev. B
5
LANGUAGE SELECTION
ENGLISH
SPANISH
FRENCH
GERMAN
ITALIAN
PORTUGUESE
EXIT
17
6
20
•
Default setting is
English.
•
Characters
ã
and
õ
are not available in Portuguese.
SET PASSWORD
PASSWORD: * *
CONTINUE
CANCEL
6
18
A B C D E F G H I J K L M N O P Q R S T
U V W X Y Z a b c d e f g h i j k l m n
o p q r s t u v w x y z 0 1 2 3 4 5 6
7 8 9 / -
•
Passwords can be from 1 to 8 characters.
•
Asterisks appear when characters are selected.
•
Use
Zoom In
to move cursor one space to right in
Password
•
Use
Zoom Out
to move cursor one space to left in
Password
•
Use
Pan
and
Tilt
to move highlight around character field
•
Press
Focus Far
to accept highlighted character
•
The
SPACE
character is located between the
z
and
0
(zero).
•
To accept password, move highlight to
Continue
, then press
Focus
Far
.
Re-enter for Verification
appears on screen.
•
To cancel password programming, move highlight to
Cancel
, then
press
Focus Far
.
•
To set or change password, the same password must be entered twice.
After 2nd successful entry, screen
6
appears
•
Password Protection
must be set to
ON
for password to be
activated. See screen
6
.
ENTER PASSWORD
PASSWORD: * *
CONTINUE
CANCEL
19
A B C D E F G H I J K L M N O P Q R S T
U V W X Y Z a b c d e f g h i j k l m n
o p q r s t u v w x y z 0 1 2 3 4 5 6
7 8 9 / -
•
Passwords can be from 1 to 8 characters.
•
Asterisks appear when characters are selected.
•
Use
Zoom In
to move cursor one space to right in
Password
•
Use
Zoom Out
to move cursor one space to left in
Password
•
Use
Pan
and
Tilt
to move highlight around character field
•
Press
Focus Far
to accept highlighted character
•
The
SPACE
character is located between the
z
and
0
(zero).
•
To accept password, move highlight to
Continue
, then press
Focus
Far
. If password is correct, screen
1
appears. Otherwise, Enter
Password screen remains.
•
To cancel password entry, move highlight to
Cancel
, then press
Focus Far
. The dome resumes normal operating mode.
SELECT CONTINUE TO RESET
CONTINUE
CANCEL
DOME MUST RESET TO
CHANGE LANGUAGE
20
17
•
Dome must reset for language change to occur. With highlight bar on
Continue
, press
Focus Far
to continue with language change.
•
To cancel language change, use the
Tilt
control to move highlight bar
to
Cancel
. The Language Selection screen (screen
18
) displays.
AD, American Dynamics, DeltaDome,
and the
AD logo
are trademarks
of Sensormatic Electronics Corporation. Other product names (if any)
mentioned herein may be trademarks or registered trademarks of other
companies.
No part of this guide may be reproduced in any form without written
permission from Sensormatic Electronics Corporation.
© Copyright 1998. All rights reserved. BSL 9/98
1 or 19
Blank
Space
Reset Dome
Blank
Space
18 or 6
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5

American Dynamics AD615 Quick Reference Manual

Brand
American Dynamics
Model
AD615
Type
Quick Reference Manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents