Becker BXP6402 Quick start guide

BXP6402
Becker
Brand
Becker
Model
BXP6402
Type
Quick start guide

This manual is also suitable for

Becker BXP6402 is a Mode S transponder designed for general aviation aircraft. Its features include:

  • High-resolution altitude reporting: Provides precise altitude information to air traffic control, enhancing safety and efficiency.

  • UPS AT capability: Allows the transponder to automatically switch to standby mode in the event of a power failure, ensuring uninterrupted communication.

  • Altitude select function: Enables the pilot to manually input their desired flight level, simplifying altitude setting and reducing workload.

  • Error latch clearing: Allows the pilot to clear any error messages displayed on the transponder, facilitating troubleshooting and maintaining reliable operation.

Becker BXP6402 is a Mode S transponder designed for general aviation aircraft. Its features include:

  • High-resolution altitude reporting: Provides precise altitude information to air traffic control, enhancing safety and efficiency.

  • UPS AT capability: Allows the transponder to automatically switch to standby mode in the event of a power failure, ensuring uninterrupted communication.

  • Altitude select function: Enables the pilot to manually input their desired flight level, simplifying altitude setting and reducing workload.

  • Error latch clearing: Allows the pilot to clear any error messages displayed on the transponder, facilitating troubleshooting and maintaining reliable operation.

Installation Instruction
BE6400-01-(XX)
Installation Instruction
BE6400-01-(XX)
Configuration is complete now.
Switch the transponder to "ALT" and check if the
correct flight level is displayed.
This Installation instruction describes the configuration
of the Becker BXP6401-X-(XX) transponder after the
installation of the Blind Encoder BE6400-01-(XX). It is
not a substitute for the Installation and operation
manual BE6400-01-(XX).
BE6400-01-(XX)
Blind Encoder
Installation Instruction
ISSUE 1 03/07
Article-No. 0599.735-079 Becker Avionics GmbH
Installation Instruction
BE6400-01-(XX)
Installation Instruction
BE6400-01-(XX)
Configuration is complete now.
Switch the transponder to "ALT" and check if the
correct flight level is displayed.
This Installation instruction describes the configuration
of the Becker BXP6401-X-(XX) transponder after the
installation of the Blind Encoder BE6400-01-(XX). It is
not a substitute for the Installation and operation
manual BE6400-01-(XX).
BE6400-01-(XX)
Blind Encoder
Installation Instruction
ISSUE 1 03/07
Article-No. 0599.735-079 Becker Avionics GmbH
Installation Ins
t
r
uc
t
i
on
BE6400-01-(XX)
Installation Ins
t
r
uc
t
i
on
BE6400-01-(XX)
Mechanical Installation
BE6400-01-(XX) is designed for installation in an
aircraft together with the Becker Mode S transponder
BXP6401 or BXP6402. It can be mounted on the J8
unit connector.
For mechanical stabilization the blind encoder must be
fastened with a device at the housing of the
transponder (see figure below).
The sensor of the blind encoder must be connected
with the outer air over a flexible air pressure tube. The
inner diameter of the tube must be 4 mm. The sensor
herewith gets the outer air pressure of the respective
aircraft for altitude measurement.
Note: The protection cover must be removed before
connecting the air pressure tube.
Configuration of the transponder
The configuration setting of the transponder must be
adapted in the following way (supposing that
programmed Address Module and antenna are
connected):
1) Switch the transponder to "SBY".
2) Press the "SEL" button.
3) Turn the rotary knob until "INS" appears in the
lower left corner of the display.
4) Press the rotary button. "PASSWORD" appears in
the display.
5) Enter "6435" by turning the rotary knob and press
it to go to the next digit.
6) Press the "STO" button. The display shows "ALTM
SELECT".
7) Check if "UPS AT" is marked. If yes, go to 10.
8) Turn the rotary knob until "UPS AT" is highlighted.
9) Press the "STO" button to select "UPS AT".
10) Press the rotary button until "SPECIALS" appears.
11) Check if "ALTM HIGH RESOL" is marked. If yes
go to 14.
12) Turn the rotary button to select "ALTM HIGH
RESOL".
13) Press the "STO" button to set high resolution.
14) Press the rotary button until "ERROR LATCHES"
appears in the display.
15) Turn the rotary button to select "CLEAR
LATCHES".
16) Press the "STO" button to clear the error latches.
17) Press the "SEL" button to leave the menu.
Installation Ins
t
r
uc
t
i
on
BE6400-01-(XX)
Installation Instruction
BE6400-01-(XX)
Mechanical Installation
BE6400-01-(XX) is designed for installation in an
aircraft together with the Becker Mode S transponder
BXP6401 or BXP6402. It can be mounted on the J8
unit connector.
For mechanical stabilization the blind encoder must be
fastened with a device at the housing of the
transponder (see figure below).
The sensor of the blind encoder must be connected
with the outer air over a flexible air pressure tube. The
inner diameter of the tube must be 4 mm. The sensor
herewith gets the outer air pressure of the respective
aircraft for altitude measurement.
Note: The protection cover must be removed before
connecting the air pressure tube.
Configuration of the transponder
The configuration setting of the transponder must be
adapted in the following way (supposing that
programmed Address Module and antenna are
connected):
1) Switch the transponder to "SBY".
2) Press the "SEL" button.
3) Turn the rotary knob until "INS" appears in the
lower left corner of the display.
4) Press the rotary button. "PASSWORD" appears in
the display.
5) Enter "6435" by turning the rotary knob and press
it to go to the next digit.
6) Press the "STO" button. The display shows "ALTM
SELECT".
7) Check if "UPS AT" is marked. If yes, go to 10.
8) Turn the rotary knob until "UPS AT" is highlighted.
9) Press the "STO" button to select "UPS AT".
10) Press the rotary button until "SPECIALS" appears.
11) Check if "ALTM HIGH RESOL" is marked. If yes
go to 14.
12) Turn the rotary button to select "ALTM HIGH
RESOL".
13) Press the "STO" button to set high resolution.
14) Press the rotary button until "ERROR LATCHES"
appears in the display.
15) Turn the rotary button to select "CLEAR
LATCHES".
16) Press the "STO" button to clear the error latches.
17) Press the "SEL" button to leave the menu.
Installation Instruction
BE6400-01-(XX)
Installation Instruction
BE6400-01-(XX)
Configuration is complete now.
Switch the transponder to "ALT" and check if the
correct flight level is displayed.
This Installation instruction describes the configuration
of the Becker BXP6401-X-(XX) transponder after the
installation of the Blind Encoder BE6400-01-(XX). It is
not a substitute for the Installation and operation
manual BE6400-01-(XX).
BE6400-01-(XX)
Blind Encoder
Installation Instruction
ISSUE 1 03/07
Article-No. 0599.735-079 Becker Avionics GmbH
Installation Instruction
BE6400-01-(XX)
Installation Instruction
BE6400-01-(XX)
Configuration is complete now.
Switch the transponder to "ALT" and check if the
correct flight level is displayed.
This Installation instruction describes the configuration
of the Becker BXP6401-X-(XX) transponder after the
installation of the Blind Encoder BE6400-01-(XX). It is
not a substitute for the Installation and operation
manual BE6400-01-(XX).
BE6400-01-(XX)
Blind Encoder
Installation Instruction
ISSUE 1 03/07
Article-No. 0599.735-079 Becker Avionics GmbH
  • Page 1 1
  • Page 2 2
  • Page 3 3

Becker BXP6402 Quick start guide

BXP6402
Becker
Brand
Becker
Model
BXP6402
Type
Quick start guide
This manual is also suitable for

Becker BXP6402 is a Mode S transponder designed for general aviation aircraft. Its features include:

  • High-resolution altitude reporting: Provides precise altitude information to air traffic control, enhancing safety and efficiency.

  • UPS AT capability: Allows the transponder to automatically switch to standby mode in the event of a power failure, ensuring uninterrupted communication.

  • Altitude select function: Enables the pilot to manually input their desired flight level, simplifying altitude setting and reducing workload.

  • Error latch clearing: Allows the pilot to clear any error messages displayed on the transponder, facilitating troubleshooting and maintaining reliable operation.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents