Cuisinart GAS0356AS User manual

Brand: Cuisinart

Model: GAS0356AS

Category: Barbecues & grills

Type: User manual

This manual is also suitable for

Twin Oaks Dual Function Grill

Model GAS0356AS / GAS0356ASO

ASSEMBLY IN STRUC TIONS

ASSEMBLY INSTRUCTIONS:

READ ALL SAFETY WARNINGS & ASSEMBLY INSTRUCTIONS CAREFULLY

BEFORE ASSEMBLING OR OPERATING YOUR GRILL.

WE RECOMMEND TWO PEOPLE WORK TOGETHER WHEN AS SEM BLING THIS UNIT.

The following tools are required to assemble this Cuisinart Twin Oaks Pellet Grill:

• Phillips Screwdriver

• Pliers or Wrench

PARTS LIST:

1 Top Front Panel

1 Bottom Front Panel

1 Right Front Leg

1 Left Front Leg

1 Right Side Front Panel

1 Left Side Front Panel

1 Left Side Panel

1 Cart Brace

1 Cart Base

1 Left Rear Leg

1 Back Panel

1 Right Rear Leg

1 Grill Body

2 Hood Handles

1 Control Knob

1 Griddle

1 Side Burner Grate

1 Right Side Table

1 Left Side Control Panel

1 Right Side Control Panel

1 Grease Cup

2 Warming Racks

1 Ash Catcher

4 Casters

4 Cooking Grates

1 Cord Wrap

1 Heat Baffle

1 Heat Plate

3 Heat Tents

1 Grease Tray

1 Auger Housing

2 Accessory Hooks

1 Tank Block Bar

Note: Most hardware is pre-attached to the grill. You may need to loosen some screws

partially while others may need to be removed in order to assemble parts. The screws that

you remove will be re-used so don’t misplace this hardware.

Extra screws are included in a small bag with the owners manual.

4 3

Step 2

• Loosen 6 screws 3-4

turns on FRONT LEGS

and

• Do not remove screws

• Attach FRONT PANELS

and

using keyholes

• Tighten 6 screws

NOTE: Before tightening keyhole

screws, make sure panels are aligned.

• Remove 2 screws

• Attach FRONT PANELS

and

• Tighten 2 screws

Step 1

• Loosen 2 screws

• Attach LEFT SIDE

PANEL

• Tighten 2 screws on

LEFT SIDE PANEL

Step 4

• Loosen 6 screws 3-4

turns on FRONT LEGS

and

• Do not remove screws

• Attach RIGHT SIDE

FRONT PANEL

and

LEFT SIDE FRONT

PANEL

• Tighten 6 screws on

RIGHT SIDE FRONT

PANEL

and LEFT

SIDE FRONT PANEL

Step 3

• Attach CART BASE

• Tighten 4 screws

(Removed from

Step 5)

Step 6

• Loosen 2 screws

• Attach CART BRACE

• Tighten 2 screws on

CART BRACE

• Remove 4 screws

Step 5

Remove 2 screws

• Loosen 9 screws on

REAR LEGS

and

• Attach BACK PANEL

to REAR LEGS

and

• Tighten 5 screws

• Remove 4 screws

• Attach CART BASE

rear legs

• Tighten 4 screws

(Removed from Step 7)

Remove 2 screws

Step 7

Step 8

• Lock CASTERS

• Attach CASTERS

legs

Step 10

CASTERS

locked

unlocked

• Attach LEFT SIDE

PANEL

and CART

BRACE

• Tighten 4 screws

Step 9

Tighten

4 screws

ACCESSORY

HOOKS

• Attach ACCESSORY

HOOKS

to LEFT

SIDE PANEL

with

wing nuts

Step 11

• Loosen 2 screws

• Install TANK BLOCK

BAR

• Tighten screws

Step 12

• Loosen 5 screws

• Remove 2 screws

Remove 2 screws

Step 14

Step 13

Loosen 5 screws

• Loosen 1 screw

• Remove 2 screws

Loosen 1 screw

Remove 2 screws

Step 15

Step 16

CART BRACKETS

• Set GRILL BODY

cart

• Make sure screw drops

into rear cart brackets

• Push GRILL BODY

back of cart

• Install 2 screws in FRONT

BRACKETS (Removed

from Step 13 and Step

14)

• Tighten 4 screws on cart

brackets (2 screws left

over will be used in future

steps)

CART BRACKETS

• Install HOOD HANDLES

(Wing nuts, bezels and

washers are pre-installed

on handles)

• Attach RIGHT SIDE

TABLE

to GRILL

BODY

using keyholes

• Do not tighten screws at

this time

• Install and tighten 2

screws (Removed from

Step 13 and Step 17)

Step 18

• Loosen 2 screws

• Attach RIGHT SIDE

CONTROL PANEL

RIGHT SIDE TABLE

using keyholes

• Tighten 2 screws

• Remove 2 screws and

washer

Step 17

Loosen

screws

Remove

screw and

washer

Remove

screw

Install

screws

Step 20

• Install screw and washer

(Removed from Step 17)

• Make sure control panels

are aligned

• Tighten 5 screws from

Step 18 and Step 19

Step 19

Align

Panels

• Remove WING NUT and

SIDE BURNER

• Loosen 2 screws from

SIDE BURNER

VALVE

• Install SIDE BURNER

VALVE using keyholes in

RIGHT SIDE CONTROL

PANEL

and tighten

screws

• Install SIDE BURNER

and make sure BURNER

VENTURI  ts over VALVE

NOZZLE

• Tighten WING NUT

Loosen 2

screws

BURNER

VENTURI

VALVLE

NOZZLE

WING

NUT

Install

screw and

washer

Step 22

Step 21

• Attach CONTROL

KNOB

• Attach ELECTRODE

WIRE to IGNITOR

Step 24

• Loosen 2 screws from

LEFT SIDE CONTROL

PANEL

• Remove 1 screw

Step 23

• Attach LEFT SIDE

CONTROL PANEL

PELLET HOPPER using

keyholes

Remove

screw

• Remove 4 screws and

washers from AUGER

HOUSING

• Loosen 1 screw

Step 26

Step 25

Loosen

screw

Remove

4 screws

• Install and tighten 2

screws (Removed from

Step 14 and Step 23)

• Install AUGER HOUSING

using keyhole in

 rebox and slots in pellet

hopper bracket

• Tighten 5 screws and

washers in  rebox

Step 27

• Remove 2 screws

• Attach CORD WRAP

using 2 screws

Step 28

• Once connected, twist to

tighten

Step 29b

• Connect wiring for

Controller and Pellet

Sensor

• These wires can only be

connected one way

• Make sure the connectors

are lined up properly

before tightening

Step 29a

• Secure wiring with cord

clip.

Step 29c

• Attach HEAT BAFFLE

Step 31

Step 30

• Install SIDE BURNER

GRATE

Step 33

• Install HEAT TENTS

above each burner

Step 32

• Install HEAT PLATE

on welded brackets

Page is loading ...

Cuisinart GAS0356AS User manual

Brand: Cuisinart

Model: GAS0356AS

Category: Barbecues & grills

Type: User manual

This manual is also suitable for

Download PDF

report

Cuisinart GAS0356AS User manual

This manual is also suitable for

Cuisinart GAS0356AS User manual

Related papers

Other documents