Cuisinart GAS9456AS Reference guide

Deluxe Four Burner Gas Grill

Model GAS9456AS / GAS9456ASO

ASSEMBLY IN STRUC TIONS

1

ASSEMBLY INSTRUCTIONS:

READ ALL SAFETY WARNINGS & ASSEMBLY INSTRUCTIONS CAREFULLY

BEFORE ASSEMBLING OR OPERATING YOUR GRILL.

WE RECOMMEND TWO PEOPLE WORK TOGETHER WHEN AS SEM BLING THIS UNIT.

The following tools are required to assemble this Cuisinart 4 Burner Gas Grill:

• Phillips Screwdriver

Note: Most hardware is pre-attached to the grill. You may need to loosen some screws

partially while others may need to be removed in order to assemble parts. The screws that

you remove will be re-used so don’t misplace this hardware.

Extra screws are included in a small bag with the owners manual.

PARTS LIST:

1 Front Right Leg

1 Front Panel

1 Front Left Leg

1 Side Panel

1 Left Side Panel

1 Cart Brace

1 Cart Base

1 Left Rear Leg

1 Back Panel

1 Right Rear Leg

1 Side Burner Grate

4 Heat Tents

1 Side Burner Knob

1 Right Side Control Panel

1 Grease Cup

1 Warming Rack

1 Heat Shield

1 Right Side Table

1 Left Side Table

1 Grill Body

1 Left Side Control Panel

4 Casters

3 Cooking Grates

1 Grease Tray

1 Bar

1

2

3

4

5

6

7

8

11

9

10

12

13

14

15

16

17

18

19

20

21

22

23

24

25

2

20

19

18

21

14

16

23

12

11

15

13

8

5

9

6

17

3

2

1

7

4

24

10

22

25

3

Step 1

• Loosen 6 screws

3-4 turns

• Do not remove

screws

• Attach FRONT

PANEL using

keyholes

• Tighten 6 screws

• Loosen 3 screws

• Attach SIDE

PANEL

• Tighten 3 screws

on SIDE PANEL

Step 2

FRONT PANEL

SIDE PANEL

1

2

3

4

1

2

3

2

4

NOTE: Before tightening keyhole

screws, make sure panels are aligned.

4

• Loosen 2 screws

• Attach LEFT

SIDE PANEL

• Tighten 2 screws

on LEFT SIDE

PANEL

• Remove 6 screws.

• Attach CART

BRACE.

• Tighten two

screws on CART

BRACE.

Remove 2 screws

Step 3

Step 4

LEFT

SIDE

PANEL

CART BRACE

1 2 3

5

1 2 3

5

6

5

6

5

• Attach CART BASE

• Make sure TANK

• BRACKETS are on this

end. (See drawing below)

• Tighten 4 screws

(Removed from Step 4)

• Loosen 6 screws

• Attach BACK

PANEL

• Tighten 4 screws

• Remove 6 screws

Remove 2 screws

Tighten 4 screws

Step 5

Step 6

CART BASE

BACK PANEL

7

1

2

3

4

9

10

8

7

9

TANK BRACKETS

6

• Attach CART

BASE to back

legs

• Tighten 4 screws

(Removed from

Step 6)

• Attach LEFT SIDE

PANEL and

CART BRACE

• Tighten 4 screws

CART BASE

Step 7

Step 8

LEFT

SIDE

PANEL

7

8

9

10

5

6

Screws removed

from Step 6

CART BRACE

7

• Lock CASTERS

• Attach CASTERS

to legs

• Set cart upright on

CASTERS

unlocked

locked

Step 9

Step 10

CASTERS

9

3

6

7

8

• Loosen 2 bottom

screws

• Install BAR

• Tighten 2 screws

Step 11a

Step 11b

Tighten screw Tighten screw

BAR

6

CART BASE

TOP VIEW

Loosen bottom screws

CART BASE

9

• Set GRILL BODY

on cart

• Remove 3 screws

• Align GRILL

BODY to cart

• Rotate CART

BRACKETS

upwards and

tighten 4 screws

Step 12

Step 13

Remove screw

Remove

screw

GRILL BODY

Tighten screws

GRILL BODY

Remove screw

CART BRACKETS

Align Panels

10

• Remove 3 screws

• Align GRILL

BODY to cart

• Rotate CART

BRACKETS

upwards and

tighten 4 screws

• Remove 3 screws

and washers

Remove screw

Remove

screw

LEFT SIDE

TABLE

RIGHT SIDE

TABLE

RIGHT SIDE

CONTROL

PANEL

Step 14

Step 15

Tighten screws

GRILL BODY

Remove

screw

and

washer

Remove

screw

and

washer

Remove

screw

CART BRACKETS

11

• Loosen 4 screws

• Attach parts and

tighten screws

• Loosen 4 screws

• Attach LEFT SIDE

TABLE using

keyholes

• Do not tighten

screws at this

point in time

Step 16

Step 17

LEFT SIDE

CONTROL PANEL

RIGHT SIDE

CONTROL PANEL

LEFT SIDE TABLE

RIGHT SIDE TABLE

LEFT

SIDE

TABLE

Align

edges

Loosen 4 screws

12

• Install screw and

tighten. (screw

was removed in

Step 13)

• Install screw and

washer. (screw

and washer were

removed in step

15) Do not tighten

screw at this time.

• Make sure panels

are aligned

• Tighten 5 screws

from Step 17 & 19

Step 18

Step 19

Align Panels

13

• Loosen 4 screws.

• Attach RIGHT

SIDE TABLE

using keyholes.

Do not tighten

4 screws at this

time.

• Install screw and

tighten (screw was

removed in step

14)

Step 20

Step 21

RIGHT

SIDE

TABLE

Loosen 4 screws

14

• Install screw and

washer (screw

and washer were

removed in step

15) Do not tighten

screw at this time.

• Make sure panels

are aligned and

tighten 5 screws

from Step 20 & 22

Step 23

Step 22

• Install screw (re-

moved in step 15)

4

Align Panels

15

• Remove WING

NUT and remove

burner. Install

SIDE BURNER

VALVE in control

panel

• Rotate valve and

tighten 2 screws

to lock into place

(see diagram step

24b below)

• Install burner and

make sure

BURNER

VENTURI  ts over

VALVE NOZZLE

• Tighten WING

NUT

• Install SIDE

BURNER KNOB

Step 24a

Step 24b

VALVE

NOZZLE

SIDE BURNER

VALVE

BURNER VENTURI

WING

NUT

SIDE BURNER

KNOB

BEZEL

KEY HOLES

SIDE BURNER

VALVE STEM

16

• Attach WIRE CLIP

to side burner

WIRE CLIP

SIDE BURNER

VALVE

SIDE

BURNER

SIDE BURNER

VALVE

WIRE CLIP

SIDE

BURNER

Step 25a

Step 25b

17

• Attach IGNITOR

WIRE to ELEC-

TRODE

• Install SIDE

BURNER GRATE

Step 26

Step 27

SIDE BURNER

GRATE

ELECTRODE

IGNITER WIRE

18

• Loosen 2 screws

• Attach HEAT

SHIELD and

tighten screws

GREASE CUP

GREASE TRAY

Step 28

• Install GREASE

TRAY and

GREASE CUP

through back of

grill

Step 29

HEAT SHIELD

19

Step 30

WARMING RACK

HEAT TENTS

COOKING GRATES

• Install HEAT

TENTS,COOKING

GRATES and

WARMING

RACK

Page is loading ...

Cuisinart GAS9456AS Reference guide

Cuisinart GAS9456AS Reference guide

Related papers

Other documents