LILIN PIH - 7625 User manual

LILIN
Brand
LILIN
Model
PIH - 7625
Category
Security cameras
Type
User manual
PIH-7625 Series
INSTRUCTION MANUAL
MERIT LILIN ENT. CO., LTD
http://www.meritlilin.com 66-7625TCSE
DAY&NIGHT FAST DOME CAMERA
CONTENTS
Preface
Features
Warning & Cautions
Structural Element
Fast Dome Camera Set Up
Installation
System Configuration
Operation
DIP Switch Setting
Fan Switch
Alarm Mode
Fast Dome ID Address Setting Refer Chart
Fast Dome Connection Jack and Cable Requirement
Indoor Installation Structural Drawing (Embedded and Attached Mounting)
Outdoor Installation Structural Drawing (Pendant Mounting)
Embedded Mounting (False Ceiling)
Attached Mounting (Fixed Ceiling)
Pendant Mounting (External Housing)
Fast Dome and Keyboard
Fast Dome, Matrix and Keyboard
Fast Dome, DVR and Keyboard
Fast Dome with PC Control
Initial Power Up Inspection
Manual Operation
Fast Dome Selection
Zoom Lens Control
Focus Control
Iris Control
Horizontal 180 Instant Flip
Preset Position Setting
RS-485 Protocol Dip Switch Setting
Recalling Preset Position
Setting Preset Position Group
Changing Preset Data
............................................................................................................................
............................................................................................................................
.........................................................................................................
............................................................................................................
................................................................................................
.................................................
........................................................................
.........................................................................
..............
....................................
.......................................................................
....................................................................
.......................................................................................
............................................................................
..............................................................................
....................................................................................
....................................................................................
..................................................................................................
.........................................................................................
...........................................................................................
..................................................................................................
......................................................................................................
Pages
...........................................................................................................
.........................................................................................................
...............................................................
..............................................................................
............................................................................................
............................................................................................
.................................................................................
.......................................................................................
Activating AutoPan
Deleting Preset Data
Alarm Management
Alarm Output
Initial Setting (Factory Default)
OP. Mode Setting
RET Mode Setting
RET Time Setting
AGC Control
Sensitivity Up (Enhancement)
Back Light Compensation
Back Light Compensation Zone
Flickerless
White Balance Mode
ICR Switch
Gamma Adjustment (Brightness)
Pedestal Adjustment
Aperture Correction Adjustment
Private Mask
Operational
Camera
Optical Zoom Lens
Electrical
Environmental
Mechanical
External Housing
Quick Reference Table
Trouble Shooting
Installation Kit
Day & Night Fast Dome Function Setup (OSD Menu)
Specification
Appendix A
Appendix B
..............................................................................................
..............................................................................................
........................................................................................................
..............................................................................................................
...........................................................................................................
........................................................................................................
.................................................................................................
..................................................................................................................
...........................................................................................................
...................................................................................................
...........................................................................................
...............................................................................................
...................................................................................................
.............................................................................
........................................................................................................
..........................................................................................................
.............................................................................
.....................................................................................
............................................................................
..............................................................................................
............................................................................................
...........................................................................................................
...........................................................................
.............................................................................
.........................................................................................................
...................................................................................................
...................................................................................................
.................................................................................................
......................................................................................................
PREFACE
PIH-7625 equips with a 25X optical zoom lens adopting Sony Exview CCD and retractable IR
filter, automatically switch from high resolution color to high resolution monochrome when
light drops below 3 Lux. Additionally PIH-7625's on-screen menu offers easier and more
configuration options such as : BLC zone selection, Auto White Balance mode selection, Zoom
Speeds selection, Picture Quality adjustment...Etc.
PIH-7625T Human Tracking System Fast Dome Camera with all the features and function of
LILIN's PIH-7625 Day&Night Fast Dome camera and built-in intelligent video processing chip,
which enhances the moving object analysis, improves the human feature distinguishing accuracy,
and lowers the false action occurrence. Different from the other tracking system tiding with
several cameras, our newly developed technology allows us to execute the motion tracking
function with single camera. The system will auto-zoom on the size of the invader, and monitors
the object on the screen center.
LILIN's Fast Dome series measure only 145mm (5.6") in diameter and is capable of making 360
degrees continuous rotation with a speed range of 0.18 to 360 degrees per second, ensures direct
and accurate target positioning. When required the dome can be quickly spun throught 180
degrees, an important feature when something passes directly under the camera.
Up to 128 preset positions can be programmed and recalled with an accuracy of 0.25 degrees.
First 16 presets can be divided into 4 groups for auto touring with individual setting for speed
and dwell time.
Each Fast Dome has 6 alarm inputs (expandable to 64) can drive the dome to any position in
under second. A local alarm output can be configured as NO or NC and two types of alarm
response mode provide flexible alarm management. RS-485 control interface makes our fast
dome cameras easy to fit into our exist systems and compatible with other manufacturers's
control systems.
LILIN's Fast Dome series are fully-functional and user-friendly. It will meet your need for a wide
range of surveillance applications. The application for LILIN tracking dome are (1) Access control
area (Bank Chest, Military Magazine, Oil or Chemical tank...). (2) After hour monitoring area
(Warehouse, Archives, Parking exit...). (3) Educational Institution or Video Conference.
(4) Ceremony
1
25X Auto Focus Lens
Build-in 25X optical zoom lens with focal length 3.8 ~ 95.0mm
Automatic / Manual Iris Control
360 continuous rotation
Up to 128 programmable preset positions
Preset positions auto scanning
High speed rotation and tilt, speed range varies from 0.18 /sec ~ 360 /sec
180 Horizontal Instant Flip
6 alarm inputs, 1 alarm output can be set as NO (normally open) or NC (normally close) for
each Fast Dome
Two types of alarm response mode: Lock Mode, Release Mode
Build in 1/4" CCD high resolution DSP colour camera:
1. Color / Mono Switch (IR Cut Filter)
ON Color
OFF Mono
AUTO Switch from color to mono when light drops below 3 lux.
2. 480 TV Lines (Color) ; 520 TV Lines (Mono)
3. 0.1Lux (Color) ; 0.01Lux (Mono)
4. On-Screen Setup Menu.
5. White Balance Control :Auto Correction ,Auto Tracking , Fix (Indoor/Outdoor)
6. Back Light Compensation (On/Off)
l
l
l
l
l
l
l
l
l
l
FEATURES
2
l
l
l
l
l
7. Back Light Compensation Zone (Top , Bottom , Left , Right, Center)
8. Auto Gain Control : 8dB (low) , 22dB (medium) , 36dB (high)
9. 8 levels Brightness Adjustment
10. 16 levels Pedestal Adjustment
11. Aperture Correction Adjustment
12. Flickerless : On/Off
13. Sensitivity Enhancement : On/Off
RS-485 control interface
Up to 64 Fast Dome configuration
Compatible with PC control (protocol required)
12Vdc voltage input (power supply options: 90 ~ 260Vac or 24Vac)
Flexible Mounting: Indoor - embedded and attached types, Outdoor - with weather resistant
housing
3
Human Tracking System Function (PIH-7625T)
1. PIH-7625T series are smart sensor and built-in intelligent video processing which has
surveillance applications on,
(1) Detection motion object.
(2) Tracking and zooming motion object.
2. PIH-7625T series have two modes:
(1) Manual tracking mode (Keyboard mode).
(2) Auto tracking mode (user can setup the schedule to active the auto tracking function once a
day).
3. If more than one moving object available in the camera FOV (Field of View) then the camera
will track moving object that has highest priority. The highest priority means moving object
with largest motion or its position is nearest the camera.
4. The speed of camera pan-tilt is automatically relative to the speed of moving object.
5. The zooming application will active if,
Zoom-In
The position of moving object is near the center of FOV and its size is approximately smaller
than 1/6 of FOV.
Zoom-Out
The size of moving object is approximately larger than 1/6 of FOV.
The position of moving object at the outside of FOV, on the other hand the moving object
almost moving out of FOV.
6. The zoom application has 0-35 step of zoom-in/out.
7. PIH-7625T uses the preset-1 as "Home" position of auto tracking mode.
8. The auto tracking mode always checks the idle condition. Idle condition is condition where the
moving object not appears in the camera view. When the system on the idle condition, it will
check the previous status of tracking, if previous status on tracking condition then camera will
do zoom-out two steps otherwise if the idle condition is approximately 10 second then camera
will return to home position (preset 1).
9. The limitation of tracking object moving speed
10. Tracking object must larger than 50TV Lines.
Length of monitor area
(m)
6
12
25
50
Above data for reference only
Limitation of tracking
speed (km/hr)
10
20
40
80
Tracking object possible location distance
(Wide side with view angle 39.2 )
5m
10m
20m
40m
Please read the manual before attempting installation or operation
1. Please be aware to the warnings and cautions notice.
2. Don't use any chemical detergent to clean the machine surface, use a damp cotton cloth
only. Regularly clean the dome cover to assure proper focus ability.
3. Please install the Fast Dome in a dry area, water and high humidity may cause damage on
internal parts. External housing should be used for outdoor installation.
4. Please use parts supplied by the manufacturer only, any unqualified part using in the
equipment may violate the warranty.
5. Avoid installing the equipment in an unstable area. Make sure the area is firm and stable.
Falling equipment may injure personnel and damage the equipment.
6. Do not install the equipment near any flammable gas. Violation may cause fire or injury.
7. Avoid running video cable and signal cable through or passing interference sources such
as video waves, broadcast station, power generator, elevator motor or high voltage area
..... etc. Violation may cause interference.
8. Make sure the power cable is properly fixed. Un-suitably fixed cable may cause serious
short circuit or fire.
9. Correct cable connection is important. Do not place any object on the connection cable
and change the cable if there is damage on cable. Violation may cause short circuit, fire
and injury.
10. Make sure ground is well connected to avoid damage caused by lightning.
11. Do not put any foreign objects inside the equipment and do not spray any liquid on
equipment. This will avoid short circuit damage.
12. Do not touch power connection with wet hands to avoid short circuit or electricity shock.
13. Do not apply smash-force on the equipment. Violation may cause damage.
14. Do not install the equipment in a location that may expose the equipment directly to
sunlight. Violation may cause colour fading or damage.
15. Do not install the equipment in high temperature or low temperature environment to
avoid damage. The normal operational temperature is between -10 C ~ +50 C.
16. Fast Dome contains high sensitive electric parts inside. Do not try to repair them without
qualified personnel.
17. Turn off the power immediately and contact the technician when the following occurs:
A. Damage on power cable or plug.
B. Water leak into the equipment.
C. Fast Dome can not be operated normally.
D. Equipment falling on ground or damage on external case.
E. Unusual occurrence.
18. Warning: Do not try to repair the equipment. Only a qualified technician may disassemble
and repair the equipment. Shut off the power before disassemble the equipment and don't
put power on unless the case is completely assembled.
WARNINGS & CAUTIONS
4
Dome Cover
Camera Case
Decoration Ring
RS-485 In / Out Terminal
Alarm In / Out Terminal
Video Out Jack
Power In Jack
Camera Base
STRUCTURAL ELEMENT
5
DIP Switch Setting
Fan Power Switch
Alarm Mode Switch
Turn the number 2 switch to ON position to activate the internal fan. This will maintain the
temperature inside and make the electric parts longer life.
Alarm Mode can be set as Lock or Release mode. Turn number 1 switch to ON position to
choose Release mode. Turn number 1 switch to OFF position to choose Lock mode.
Fast Dome has 6 alarm inputs and 1 output, which can be set either NC (normally close) or
NO (normally open) mode. Turn number 2 switch to ON position to choose NC mode.
Turn number 2 switch to OFF position to choose NO mode.
Camera ID Switch
Alarm Mode Switch
Fan Power Switch
FAST DOME CAMERA SET UP
6
RS-485 Protocol Dip Switch
Fast Dome ID Address Setting Refer Chart
Up to 64 Fast Dome Camera can be serial linking in one system.
Therefore each dome is addressing by ID switch located at the base of the Fast Dome.
When select MLP1 (MERIT LILIN PROTOCOL 1), Camera ID setting as followings:
15432 76 8
ON
1 5432 76 8
ON
1
1
2 3 45
ON
867
5432 76 8
ON
ON
1
1
5432768
2 345 867
ON
1
1
2 345
ON
867
5432 76 8
ON
76854321
1 2345
ON
867
ON
1
1
5432 76 8
ON
2345 867
ON
1
1
5432
ON
768
2 345 867
ON
1
1
2 345
ON
867
5432 76 8
ON
12 34 5 867
1
1
5432 768
ON
5432
ON
768
1
1
ON
2345 867
ON
5432
ON
768
1
1
1
8672345
2345
ON
867
5432 768
ON
1
1
5432 768
ON
2345
ON
867
1
1
ON
2345
ON
867
5432
ON
768
1
1
1
7685432
2345
ON
867
5432 768
ON
1 2345 867
ON
ON
12 3 4 5 867
1
1
5432 768
ON
5432
ON
768
1
1
ON
2345 867
ON
5432
ON
768
1
1
1
8672345
2345
ON
8
67
5432 768
ON
1
1
5432 768
ON
2345
ON
867
1
1
ON
2345
ON
867
5432
ON
768
1
1
1
7685432
2345
ON
867
5432 768
ON
1 2345 867
ON
ON
15432768
1
1
2345
ON
867
2345
867
ON
1
1
ON
5432
ON
768
2345 867
ON
1
1
1
5432768
5432 768
ON
2345
ON
867
1
1
2345
ON
867
5432
768
ON
1
1
ON
5432
768
ON
2345 867
ON
1
1
1
2345 867
5432 768
ON
2345
ON
867
1 5432
ON
768
ON
17
33 49
1
218
34 50
5135
193
5236
204
5337
215
5438
226
5539
237
5640
248
64
63
62
61
60
57
59
58
48
47
46
45
44
41
43
42
32
31
30
29
28
25
27
26
16
15
14
13
12
9
11
10
7
1
1
5
5
4
4
3
3
2
2
7
7
6
6
8
8
ON
ON
1 5432 76 8
ON
1
1
2 3 45
ON
867
5432 76 8
ON
ON
1
1
5432768
2 345 867
ON
1
1
2 345
ON
867
5432 76 8
ON
76854321
ON
1
1
5432 768
ON
2345 867
ON
1
1
5432
ON
768
2 345 867
ON
1
1
2 345
ON
867
5432 76 8
ON
1
1
5432768
5432
ON
768
1
1
ON
2345 867
ON
5432
ON
768
1
1
1
8672345
2345
ON
867
5432 768
ON
1
1
5432 768
ON
2345
ON
867
1
1
ON
2345
ON
867
5432
ON
768
1
1
1
7685432
2345
ON
867
5432 768
ON
1
1
2
2
3
3
4
4
5
5
8
8
6
6
7
7
ON
ON
ON
1
1
5432768
5432
ON
768
1
1
ON
2345 867
ON
5432
ON
768
1
1
1
8672345
2345
ON
8
67
5432 768
ON
1
1
5432 768
ON
2345
ON
867
1
1
ON
2345
ON
867
5432
ON
768
1
1
1
7685432
2345
ON
867
5432 768
ON
1
1
2
2
3
3
4
4
5
5
8
8
6
6
7
7
ON
ON
ON
1
1
2345 867
2345
867
ON
1
1
ON
5432
ON
768
2345 867
ON
1
1
1
5432768
5432 768
ON
2345
ON
867
1
1
2345
ON
867
5432
768
ON
1
1
ON
5432
768
ON
2345 867
ON
1
1
1
2345 867
5432 768
ON
2345
ON
867
1
1
5
5
4
4
3
3
2
2
ON
7
7
6
6
8
8
ON
ON
17
33 49
1
218
34 50
5135
193
5236
204
5337
215
5438
226
5539
237
5640
248
64
63
62
61
60
57
59
58
48
47
46
45
44
41
43
42
32
31
30
29
28
25
27
26
16
15
14
13
12
9
11
10
When select MLP2 (MERIT LILIN PROTOCOL 2), Camera ID setting as followings:
8
RS-485 Protocol Dip Switch Setting
Explanation of DIP Switch setting
1. RS-485 IN-TML RES.
2. RS-485 OUT-TML RES.
3. HALF / FULL
4. BAUD SEL1
5. BAUD SEL2
6. PROTOCOL SEL1
7. PROTOCOL SEL2
8. PROTOCOL SEL3
9. PROTOCOL SEL4
10.
RS-485 IN Terminal Resistor ON/OFF
RS-485 OUT Terminal Resistor ON/OFF
2 wiring system (HALF duplex) or 4 wiring system (FULL duplex)
Baud Rate Select 1
Baud Rate Select 2
Protocol Select 1
Protocol Select 2
Protocol Select 3
Protocol Select 4
No Use
RS-485 In/Out Terminal Resistor setting
Daisy Connection: Set RS-485 In and Out terminal resistor as ON (factory Initialize).
Parallel Connection: Set the front and last equipments terminal resistor as ON. The parallel
connection equipment in the middle set as OFF to keep the best transmitted status.
Select RS-485 transmission mode
2 wiring system(half duplex) transmission mode: most system will use this mode due to
less wiring and lower cost but can not transmit and receive data at same time.
4 wiring system(full duplex) transmission mode: some system will require transmit and
receive data at the same time.
Baud Rate Setting
Remark LILIN Protocol control mode is N, 8, 1 Baud Rate : 9600 bps
DIP SWITCH
2 wiring system (HALF duplex)
4 wiring system (FULL duplex)
3
OFF
ON
BAUD RATE SELECTION
DIP SWITCH
2400 bps
4800 bps
9600 bps
19200 bps
5
ON
ON
OFF
OFF
4
ON
ON
OFF
OFF
9
Protocol Setting
Remark LILIN
MLP1 (MERIT LILIN PROTOCOL 1) is same as PIH-717 Protocol.
MLP2 (MERIT LILIN PROTOCOL 2) is new version LILIN Protocol.
RS-485 Protocol Dip Switch of LILIN PIH-7625 series setting
PROTOCOL SELECTION
DIP SWITCH
MLP2 (MERIT LILIN PROTOCOL 2) VERSION
MLP1 (MERIT LILIN PROTOCOL 1) VERSION
97
ON ON
ON ON
86
ON
ON
ON
OFF
RS-485 Protocol Dip Switch setting
DIP SWITCH
MLP2 Version
MLP1 Version
10987654321
OFF ON ON ON ON OFF ON OFF ON ON
OFF ON ON ON OFF OFF ON OFF ON ON
10
Fast Dome Connection Jack and Cable Requirement
1. Power In Jack
2. Video Out BNC Jack
3. Alarm In / Out Terminal
4. RS-485 In / Out Terminal
DC12V Input Voltage, Power Consumption 1.2Adc, Center Pin 2.0mm
Require Cable: 18 AWG x 2C
Video Signal Output CVBS 1.0Vpp 75 BNC
Recommend Data Cable: 5C2V
Each fast dome contains 6 alarm inputs and 1 alarm output
Alarm Input Voltage 5.6Vmax, Output 0.5A 120Vac / 1A 24Vdc
Recommend Data Cable: UL 26 AWG 80 C 300V
RS-485 Input (TXDI+,TXDI-) to receiver signal from keyboard, matrix, DVR or
multiplexer through twisted pair cable.
RS-485 Output (TXDO+,TXDO-) sending out signal to next fast dome through twisted pair
cable.
Recommend Data Cable: 2547 VW-ISC UL 24 AWG x 2C
Transmission Distance: Max. 1 Kilometer
When 24VAC PSU is used, the recommend cables are:
UL SPT-1 VW-1 18AWG x 2C
UL SPT-2 VW-1 18AWG x 2C
UL SUT 105 C VW-1 18AWG x 3C
The distance between 24Vac PSU and fast dome can not exceed 200 meters.
Center Pin
UL 24 AWG 80 C 300V
(Alarm Input)
(Alarm Output)
11
Indoor Installation Structural Drawing
Embedded Mounting Attached Mounting
INSTALLATION
12
Outdoor Installation Structural Drawing (Pendant Mounting)
13
Embedded Mounting (False Ceiling)
l Drill a 3/32" (2.4mm) hole at the center of
the chosen area.
l Useapencilandacompassestomarka
circle 6.7" (170mm) in diameter and cut
the circle.
l Attach the ring to ceiling l Ring size and screw
location
l Tighten the three tapping
screws into the ceiling or
three machine screws with
three screw nuts
l Turn the dome cover
anti-clockwise
l Separate the dome
cover from camera
Step 1 Ceiling Preparation
Step 2 The Ceiling Ring
Step 3 The Fix Ring
14
l PutonthethreeL
shape screw nuts
l Tighten the three
black screws into
the screw nuts
l Attach fix ring
with screw nuts
l Unplug the
connection cable
Setting Fast Dome ID
Setting Alarm Mode
Setting RS-485 Protocol
Setting Fan Power
l Untighten the three
screws from the base
l Separate the camera
body and base
l Turn the camera
body anti-clockwise
l Reconnect the
connection cable
l Tighten the three
screws to fix the
camera body
l Attach camera
body to base
l Turn camera body
clockwise to tight
position
Step 4 Camera Setting
Step 5 Attach the Camera Body and Base
15
l Connect RS-485
cable
l Connect alarm
cable
l Connect video
signal cable
Step 6 Connection
l Put on decoration
ring
l Turntheringclockwise
to tight position
l Put camera body and
the fix ring into the hole
l Tighten three
black screws
l Turn the camera body
clockwise to tight position
l Attach dome cover
to camera body
l Turn the dome cover
clockwise to tight position
Step 7 Install Camera Body and Decoration Ring
Step 8 Install The Dome Cover
16
Note : After dome cover is attached, use glass-cleaning cloth to clean dome cover.
Unclean dome cover may affect camera performance.
l Turn the dome cover
anti-clockwise
l Untighten the three
screws from base
l Separate the dome
cover from camera
l Turn the camera cover
anti-clockwise
l Unplug the
connection cable
l Separate the camera
body to the base
l Attach base to ceiling l Base size and
screw location
l Tighten the three
tapping screws into
the ceiling
Attached Mounting (Fixed Ceiling)
Step 1 Fix The Base
Step 2 Camera Setting
17
Setting Fast Dome ID
Setting Alarm Mode
Setting RS-485 Protocol
Setting Fan Power
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59

LILIN PIH - 7625 User manual

LILIN
Brand
LILIN
Model
PIH - 7625
Category
Security cameras
Type
User manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents