Manitowoc CVD2075 Installation guide

S Model QuietQube®Ice Machines

with CVD®Technology

Installation Training

³Compressor, Condenser,

Accumulator and HPCV are Outside

³Line Set is:

³High Pressure Liquid Line

³Low Pressure Suction Line

³Evaporator, Receiver and Harvest Valve in

Head Section

No Interconnecting Control Wiring!

Overview

Typical QuietQube System

Installation

Model Numbers

This training covers the following models:

CVD1085

SD1072C

SY1074C

CVD2075

SD2072C

SY2074C

CVD1885

SD1872C

SY1874C

CVD1485

SD1472C

SY1474C

CVD1285

SD1272C

SY1274C

CVD0885

SD0872C

SY0874C

CVD0675

SD0672C

SY0674C

CVD Condensing UnitIce Machine Head Section

Important Information

Prior to Installation

WARNING

PERSONNEL INJURY POTENTIAL

Do not operate equipment that has been misused,

abused, neglected, damaged, or altered/modified

from that of original manufactured specifications.

WARNING

Prior to installation make sure that all bin adapters

and ice deflectors

When using a non-Manitowoc ice storage system

with Manitowoc ice machines, contact the

manufacturer to assure their ice deflector is

compatible with Manitowoc ice machines.

³Read Installation, Use & Care Manual

S Model QuietQube ice machines cannot

be stacked.

Failure to follow installation guidelines may

affect warranty coverage.

Manitowoc remote systems are only

approved and warranted as a complete

new package. Warranty on the

refrigeration system will be void if a new

ice machine head section is connected to

pre-existing (used) tubing or condensing

units or vice versa.

Verify Components

³Bin

³Adapters

³Kits

³Location

Next verify that you have all the correct components

for the ice machine that is being installed

Installation Requirements

The location selected for the ice machine must meet the following criteria. If

any of these criteria are not met, select another location.

³Must have open site (gravity) drain available (see Water Supply and Drain

Requirements).

³Must have a grounded, polarized electrical power supply on a dedicated

electrical circuit (only appliance on circuit). If GFCI (ground fault circuit

interrupter) is required by your local electrical code, it must be breaker type,

not outlet type.

³Must have cold water supply line available at Ice Machine (see Water Supply

and Drain Requirements).

³Clearance and air temperatures must be met.

Head Section

Clearances

Top 5” (12.7 cm) is recommended for efficient operation and removal of top

cover/servicing.

Sides 5” (12.7 cm) is recommended for efficient operation and servicing.

There is no minimum clearance required.

Back 3” (7.6 cm) required when routing electrical inlet, water inlet and

refrigeration tubing out of the top of the unit.

5” (12.7 cm) required when routing all connections out the back.

³The air temperature must be at least 35°F (1.6°C), but must not

exceed 110°F (43.4°C).

³The location must be free of airborne and other contaminants.

³The location must not be near heat-generating equipment or in

direct sunlight.

³The location must not obstruct airflow through or around the ice

machine.

Location of Condensing Unit

³The air temperature must be at least -20°F (-28.9°C) but must

not exceed 130°F (54.4°C).

³CVD675/CVD1185/CVD2075 Only - The air temperature must

be at least -20°F (-28.9°C) but must not exceed 120°F (48.9°C).

³CVD1486 Only- The air temperature must be at least 50°F

(10°C) but must not exceed 110°F (43°C).

³The location must not allow exhaust fan heat and/or grease to

enter the condenser.

³The location must not obstruct airflow through or around the

condensing unit.

Condensing Unit Clearances

CVD675/CVD885/CVD1085/CVD1185/CVD2075

Top/Sides

There is no minimum clearance required, although 6” (15.2 cm)

is recommended for efficient operation and servicing only.

Front/Back

48” (122 cm)

CVD1285/CVD1485/CVD1885

Top/Sides

There is no minimum clearance required, although 6” (15.2 cm)

is recommended for efficient operation and servicing only.

Front

24” (61 cm)

Back

48” (122 cm)

CVD1486 ONLY

Top - 5” (12.7 cm) is required for efficient operation and

servicing.

Front/Back/Sides - 12” (30.5 cm)

CVD Rise & Drop

Verify the Condensing Unit and

Ice Machine Head Section are

within the guidelines

Electrical Service

Requirements

³All electrical work, including wire routing and grounding, must

conform to local, state and national electrical codes. The following

precautions must be observed: The ice machine must be grounded.

³A separate fuse/circuit breaker must be provided for each

condensing unit.

³A qualified electrician must determine proper wire size dependent

upon location, materials used and length of run (minimum circuit

ampacity can be used to help select the wire size).

³The maximum allowable voltage variation is +/-10 of the rated

voltage at ice machine start-up (when the electrical load is highest).

³Check all green ground screws in the control box and verify they are

tight before starting the ice machine.

Head Section Electrical

** All conductors must be solid copper wire

* Not available on S2070C models.

15 amp

#14 Solid Copper

Conductor

1.1

0.6

15 amp

115/1/60

208-230/1/60

230/1/50*

S1470C

S1870C

S2070C

15 amp

#14 Solid Copper

Conductor

2.5

1.5

15 amp

115/1/60

230/1/50

S1200C

15 amp

#14 Solid Copper

Conductor

2.5

1.5

15 amp

115/1/60

230/1/50

S1000C

15 amp

#14 Solid Copper

Conductor

1.4

0.8

15 amp

115/1/60

230/1/50

IB0620C

IB0820C

IB1020C

15 amp

#14 Solid Copper

Conductor

1.1

1.5

15 amp

115/1/60

230/1/50

S0850C

15 amp

#14 Solid Copper

Conductor

1.1

0.6

15 amp

115/1/60

230/1/50

S0600C

Minimum

Breaker Size

Required by

Manitowoc

**Minimum Wire

Size Required by

Manitowoc

Total

Amps

Maximum

Fuse/Circuit

Breaker

Voltage Phase Cycle Ice Machine

Due to continuous improvements, this information is for reference only. Please refer

to the ice machine and/or condensing unit serial number tags to verify electrical

data. Serial tag information overrides information listed here.

CVD Electrical

50 amp

40 amp

#10 Solid Copper Conductor

40.0

30.0

50 amp

40 amp

208-230/1/60

208-230/3/60

CVD2075

40 amp

25 amp

30 amp

#8 Solid Copper Conductor

#10 Solid Copper Conductor

#8 Solid Copper Conductor

25.0

20.0

40 amp

25 amp

30 amp

208-230/1/60

208-230/3/60

230/1/50

CVD1885

20 amp

15 amp

20 amp

#10 Solid Copper Conductor

#12 Solid Copper Conductor

20.0

15.0

20.0

20 amp

15 amp

20 amp

208-230/1/60

208-230/3/60

230/1/50

CVD1486

20 amp

15 amp

30 amp

#8 Solid Copper Conductor

#10 Solid Copper Conductor

#8 Solid Copper Conductor

20.0

15.0

20.0

20 amp

15 amp

30 amp

208-230/1/60

208-230/3/60

230/1/50

CVD1485

25 amp

20 amp

#10 Solid Copper Conductor

#12 Solid Copper Conductor

14.7

10.6

11.7

25 amp

20 amp

208-230/1/60

208-230/3/60

230/1/50

CVD1285

25 amp

15 amp

20 amp

#12 Solid Copper Conductor

#14 Solid Copper Conductor

#12 Solid Copper Conductor

15.7

10.8

11.2

25 amp

15 amp

20 amp

208-230/1/60

208-230/3/60

230/1/50

CVD1185

20 amp

15 amp

20 amp

#12 Solid Copper Conductor

#14 Solid Copper Conductor

#12 Solid Copper Conductor

12.5

9.4

10.9

20 amp

15 amp

20 amp

208-230/1/60

208-230/3/60

230/1/50

CVD1085

20 amp

15 amp

20 amp

#12 Solid Copper Conductor

#14 Solid Copper Conductor

#12 Solid Copper Conductor

11.8

9.1

10.0

20 amp

15 amp

20 amp

208-230/1/60

208-230/3/60

230/1/50

CVD0885

15 amp

#14 Solid Copper Conductor

9.6

7.3

9.0

15 amp

208-230/1/60

208-230/3/60

230/1/50

CVD0675

Minimum Breaker

Size Required by

Manitowoc

**Minimum Wire Size Required by

Manitowoc

Minimum

Circuit

Amps

Maximum Fuse/

Circuit

Breaker

Voltage/Phase/Cycle

Condensing

Unit

Verify Head Section

Always verify that you have received the correct

ice machine & condensing unit prior to installing

Model Number on Box

Inspection

³Remove carton & inspect ice machine and

condensing unit for shipping damage

Remove all Panels

Single Evaporator - Hinged Front Door Removal

³Loosen Screws on the left and right front panels

³Open the left front door 45 degrees and support with hand

³Depress the top pin to disengage door, tilt forward

³Lift off of bottom pin

³The right front panel lifts up to disengage

³Remove the top cover and the remaining panels

Remove all Panels

Dual Evaporator - Front Panel Removal

³Loosen Screws on the front panel

³The entire front panel lifts up to disengage

³Remove the top cover and the remaining panels

Model/Serial Number Location

Back of

Ice Machine

Inside of

Ice Machine

Example Data Plate

Refrigerant

Voltage

Manufactured

Date

Serial Number – NO Date

code in new serial numbers

Model Number

Page is loading ...

Manitowoc CVD2075 Installation guide

This manual is also suitable for

Manitowoc CVD2075 Installation guide

Related papers

Other documents