Manitowoc Ice D400 Bin Installation guide

Part Number 000014141 Rev 07 2/20

Indigo NXT Ice Machines

Installation, Operation and Maintenance Manual

Original Document

,

Caution

Read this instruction before operating this equipment.

Engineered for Ease

Safety Notices

Read these precautions to prevent

personal injury:

• Read this manual thoroughly before

operating, installing or performing

maintenance on the equipment. Failure

to follow instructions in this manual

can cause property damage, injury or

death.

• Routine adjustments and maintenance

procedures outlined in this manual are

not covered by the warranty.

• Proper installation, care and

maintenance are essential for

maximum performance and trouble-

free operation of your equipment. Visit

our website www.manitowocice.com

for manual updates, translations, or

contact information for service agents

in your area.

• This equipment contains high

voltage electricity and refrigerant

charge. Installation and repairs are

to be performed by properly trained

technicians aware of the dangers of

dealing with high voltage electricity

and refrigerant under pressure. The

technician must also be certified

in proper refrigerant handling and

servicing procedures. All lockout and

tag out procedures must be followed

when working on this equipment.

• This equipment is intended for indoor

use only. Do not install or operate this

equipment in outdoor areas.

Definitions

DANGER

Indicates a hazardous situation that, if not

avoided, will result in death or serious

injury. This applies to the most extreme

situations.

n

Warning

Indicates a hazardous situation that, if not

avoided, could result in death or serious

injury.

,

Caution

Indicates a hazardous situation that, if not

avoided, could result in minor or moderate

injury.

Notice

Indicates information considered

important, but not hazard-related (e.g.

messages relating to property damage).

NOTE: Indicates useful, extra information

about the procedure you are performing.

n

Warning

Follow these precautions to prevent personal injury during installation of this

equipment:

• Installation must comply with all

applicable equipment fire and health

codes with the authority having

jurisdiction.

• To avoid instability the installation area

must be capable of supporting the

combined weight of the equipment and

product. Additionally the equipment

must be level side to side and front to

back.

• Ice machines require a deflector when

installed on an ice storage bin. Prior to

using a non-OEM ice storage system

with this ice machine, contact the

bin manufacturer to assure their ice

deflector is compatible.

• Prior to installing a non-OEM ice storage

system with this ice machine, follow the

manufacturers installation procedures

and verify the location and installation

meets the local/national mechanical

codes and stability requirements.

• Remove all removable panels before

lifting and installing and use appropriate

safety equipment during installation

and servicing. Two or more people are

required to lift or move this appliance to

prevent tipping and/or injury.

• Legs or casters must be installed and

the legs/casters must be screwed in

completely. When casters are installed

the mass of this unit will allow it to move

uncontrolled on an inclined surface.

These units must be tethered/secured

to comply with all applicable codes.

Swivel casters must be mounted on the

front and rigid casters must be mounted

on the rear. Lock the front casters after

installation is complete.

• Connect to a potable water supply only.

• Do not damage the refrigeration circuit

when installing, maintaining or servicing

the unit.

• This equipment contains refrigerant

charge. Installation of the line sets must

be performed by a properly trained and

EPA certified refrigeration technician

aware of the dangers of dealing with

refrigerant charged equipment.

DANGER

Follow these flammable refrigeration system requirements during installation, use or

repair of this equipment:

• Refer to nameplate - Ice machine models

may contain up to 150 grams of R290

(propane) refrigerant. R290 (propane)

is flammable in concentrations of air

between approximately 2.1% and 9.5%

by volume (LEL lower explosion limit and

UEL upper explosion limit). An ignition

source at a temperature higher than

470°C is needed for a combustion to

occur. Refer to nameplate to identify the

type of refrigerant in your equipment.

• To minimize the risk of ignition due to

improper installation, replacement parts

or service procedures, only refrigeration

technicians with flammable refrigerant

training who are aware of the dangers of

dealing with high voltage electricity and

refrigerant under pressure are allowed to

work on this equipment.

• All replacement parts must be like

components obtained from the

equipment manufacturers authorized

replacement part network.

• This equipment must be installed in

accordance with the ASHRAE 15 Safety

Standard for Refrigeration Systems.

• This equipment can not be installed in

corridors or hallways of public buildings.

• Installation must comply with all

applicable equipment fire and health

codes with the authority having

jurisdiction.

• All lockout and tag out procedures

must be followed when working on this

equipment.

• This equipment contains high voltage

electricity and refrigerant charge.

Shorting electrical wires to refrigeration

tubing may result in an explosion. All

electrical power must be disconnected

from the system before servicing the

system. Refrigerant leaks, can result in

serious injury or death from explosion,

fire, or contact with refrigerant or

lubricant mists.

• Do not damage the refrigeration circuit

when installing, maintaining or servicing

the unit. Never use sharp objects or

tools to remove ice or frost. Do not use

mechanical devices or other means to

accelerate the defrosting process.

n

Warning

Follow these electrical requirements

during installation of this equipment:

• All field wiring must conform to all

applicable codes of the authority

having jurisdiction. It is the

responsibility of the end user to

provide the disconnect means to satisfy

local codes. Refer to rating plate for

proper voltage.

• This appliance must be grounded.

• This equipment must be positioned so

that the plug is accessible unless other

means for disconnection from the

power supply (e.g., circuit breaker or

disconnect switch) is provided.

• Check all wiring connections, including

factory terminals, before operation.

Connections can become loose during

shipment and installation.

DANGER

Do not operate equipment that has

been misused, abused, neglected,

damaged, or altered/modified from that

of original manufactured specifications.

This appliance is not intended for use by

persons (including children) with reduced

physical, sensory or mental capabilities,

or lack of experience and knowledge,

unless they have been given supervision

concerning use of the appliance by a

person responsible for their safety. Do

not allow children to play with, clean or

maintain this appliance without proper

supervision.

n

Warning

Follow these precautions to prevent

personal injury while operating or

maintaining this equipment:

• Read this manual thoroughly before

operating, installing or performing

maintenance on the equipment. Failure

to follow instructions in this manual

can cause property damage, injury or

death.

• Crush/Pinch Hazard. Keep hands clear

of moving components. Components

can move without warning unless

power is disconnected and all potential

energy is removed.

• Moisture collecting on the floor will

create a slippery surface. Clean up

any water on the floor immediately to

prevent a slip hazard.

• Objects placed or dropped in the bin

can affect human health and safety.

Locate and remove any objects

immediately.

• Never use sharp objects or tools

to remove ice or frost. Do not use

mechanical devices or other means to

accelerate the defrosting process.

• When using cleaning fluids or

chemicals, rubber gloves and eye

protection (and/or face shield) must be

worn.

DANGER

Follow these precautions to prevent personal injury during use and maintenance of this

equipment:

• It is the responsibility of the equipment

owner to perform a Personal Protective

Equipment Hazard Assessment to ensure

adequate protection during maintenance

procedures.

• Do Not Store Or Use Gasoline Or Other

Flammable Vapors Or Liquids In The

Vicinity Of This Or Any Other Appliance.

Never use flammable oil soaked cloths

or combustible cleaning solutions for

cleaning.

• All covers and access panels must be

in place and properly secured when

operating this equipment.

• Risk of fire/shock. All minimum

clearances must be maintained. Do not

obstruct vents or openings.

• Failure to disconnect power at the main

power supply disconnect could result

in serious injury or death. The power

switch DOES NOT disconnect all incoming

power.

• All utility connections and fixtures must

be maintained in accordance with the

authority having jurisdiction.

• Turn off and lockout all utilities (gas,

electric, water) according to approved

practices during maintenance or

servicing.

• Units with two power cords must be

plugged into individual branch circuits.

During movement, cleaning or repair it is

necessary to unplug both power cords.

• Never use a high-pressure water jet for

cleaning on the interior or exterior of

this unit. Do not use power cleaning

equipment, steel wool, scrapers or wire

brushes on stainless steel or painted

surfaces.

• Two or more people are required to

move this equipment to prevent tipping.

• Locking the front casters after

moving is the owner’s and operator’s

responsibility. When casters are installed,

the mass of this unit will allow it to move

uncontrolled on an inclined surface.

These units must be tethered/secured to

comply with all applicable codes.

• The on-site supervisor is responsible for

ensuring that operators are made aware

of the inherent dangers of operating this

equipment.

• Do not operate any appliance with a

damaged cord or plug. All repairs must

be performed by a qualified service

company.

THIS PAGE INTENTIONALLY LEFT BLANK

Table of Contents

Part Number 000014141 Rev 07 2/20 9

Safety Notices

Safety Notices ...........................................................................3

Section 1

General Information

Model Numbers ......................................................................11

Accessories ..............................................................................11

How To Read A Model Number ................................................12

Section 2

Installation

Installation ..............................................................................13

Location Requirements ............................................................ 13

Installation Requirements ........................................................13

Ice Machine Heat of Rejection .................................................14

Air Baffle .................................................................................16

Bin Installation Requirements ..................................................16

Bin Installation ........................................................................17

Dispenser Installation .............................................................. 17

Electrical Requirements ........................................................... 18

Maximum Breaker Size & Minimum Circuit Amperage Chart ....19

Water Supply and Drain Line Sizing/Connections ..................... 22

Water Connections ..................................................................22

Water Supply and Drain Connections .......................................23

Air Gap .................................................................................. 23

Cooling Tower Applications

(Water-Cooled Models) ...........................................................24

Drain Connections ...................................................................24

Remote Condenser and Condensing Unit Refrigeration

System Installation ..................................................................25

Calculating Installation Distances ......................................... 26

Remote Condenser Models .................................................. 27

QuietQube Models ............................................................... 28

Starting the Ice Machine ..........................................................32

Remove Ice Thickness Probe Shipping Brackets ................... 32

Minimum/Maximum Slab Weight ........................................ 32

Warranty .................................................................................32

Warranty Registration ........................................................... 32

Remote Ice Machine Usage with Non-Manitowoc

Multi-Circuit Condensers .........................................................33

10 Part Number 000014141 Rev 07 2/20

Table of Contents (continued)

Section 3

Operation

Touch Screen Features .............................................................35

Home Screen Icon Descriptions ............................................ 36

Setup Wizard ........................................................................... 37

Menu Screen Navigation ..........................................................38

Ice Making Sequence of Operation ..........................................39

Control Board Timers ...............................................................39

Minimum/Maximum Slab Weight ............................................41

Ice Thickness Check .................................................................41

Reverse Osmosis or Deionized Water Usage ............................42

Section 4

Maintenance

Descaling and Sanitizing ..........................................................43

Detailed Descaling and Sanitizing Procedure ............................44

Sanitizing Procedure ............................................................. 45

Parts Removal for Detailed Descaling and Sanitizing ................47

Remedial Cleaning Procedure ..................................................48

Cleaning the Air Filter and Condenser ...................................... 49

Removal from Service/Winterization .......................................49

Section 5

Troubleshooting

Before Calling for Service Checklist ..........................................51

Service Faults ..........................................................................53

Part Number 000014141 Rev 07 2/20 11

Model Numbers

This manual covers the following models:

Self-

Contained

Air-Cooled

Self-

Contained

Water-

Cooled

Remote Air-

Cooled

IDF0300A

IYF0300A

IDF0300W

IYF0300W

----

IDT0300A

IYT0300A

IDT0300W

IYT0300W

----

IYP0320A ---- ----

IDT0420A

IYT0420A

IDT0420W

IYT0420W

----

IDT0450A

IYT0450A

IDT0450W

IYT0450W

----

IDT0500A

IYT0500A

IRT0500A

IDP0500A

IDT0500W

IYT0500W

IRT0500W

----

IDT0500N

IYT0500N

IDF0500N

IYF0500N

IDP0520A

IYP0520A

----

IDF0600A

IYF0600A

IDF0600W

IYF0600W

IDF0600N

IYF0600N

IDT0620A

IYT0620A

IRT0620A

IDT0620W

IYT0620W

----

IDT0750A

IYT0750A

IRT0750A

IDT0750W

IYT0750W

IRT0750W

----

IDF0900A

IYF0900A

IRF0900A

IDF0900W

IYF0900W

IRF0900W

IDF0900N

IYF0900N

----

IDT0900A

IYT0900A

IRT0900A

IDT0900W

IYT0900W

IRT0900W

----

IDT1200A

IYT1200A

IDT1200W

IYT1200W

IDT1200N

IYT1200N

Self-

Contained

Air-Cooled

Self-

Contained

Water-

Cooled

Remote Air-

Cooled

IDT1500A

IYT1500A

IDT1500W

IYT1500W

IDT1500N

IYT1500N

IDT1900A

IYT1900A

IRT1900A

IDT1900W

IYT1900W

----

IDT1900N

IYT1900N

IRT1900N

QuietQube

Indoor Head Section

QuietQube

Air-Cooled

Condensing Unit

IYF0600C

CVDF0600

IBF0620C

IBF0820C

CVDF0900

IYF0900C

IBT1020C

CVDT1200

IDT1200C

IYT1200C

IDF1400C

IYF1400C

CVDF1400

IDF1800C

IYF1800C

CVDF1800

IDF2100C

IYF2100C

CVDF2100

Accessories

Ice Deflector

An ice deflector is required when the

ice machine is installed on a bin. An ice

deflector is not required when the ice

machine is installed on a dispenser.

Section 1

General Information

12 Part Number 000014141 Rev 07 2/20

General Information Section 1

Top Air Discharge Kit

The top air discharge kit can be used on

select ice machine models. This kit directs

warm exhaust air upward rather than out

the side panels.

AuCS® Automatic Cleaning System

This accessory reduces equipment cleaning

expense. The AuCS® accessory monitors

ice making cycles and initiates a remedial

cleaning procedure automatically.

LuminIce® II

The LuminIce® growth inhibitor recirculates

the air in the ice machine foodzone over

a UV bulb. This process will inhibit the

growth of common micro-organisms on all

exposed foodzone surfaces.

How To Read A Model Number

I Y T 1500 N — 261 X

Ice Machine Model

I - Indigo Model

IB - Ice Beverage

X - LuminIce

A - Alternate Compressor

HP - High Pressure Water

Regulating Valve

Ice Cube Size

R - Regular

D - Dice

Y - Half-Dice

Not Used On IB Models

P - Correctional Model

M - Marine Model

V - Space Saver

Q - Coated Condenser

Blank - General Usage

Refrigerant

P - R290

F - R404A

T - R410

Voltage

161 - 115/60/1

261 - 208-230/60/1

251 - 230/50/1

263 - 208-230/60/3

463 - 460/60/3

Nominal Production

Condenser Type

A - Self-Contained Air-Cooled

W - Self-Contained Water-Cooled

N - Remote Air-Cooled

C - CVD Air-Cooled

NOTE: These products are hermetically sealed and contain fluorinated greenhouse gas

R404A or R410A.

Part Number 000014141 Rev 07 2/20 13

Installation

Location Requirements

The location selected for the ice machine

head section must meet the following

criteria. If any of these criteria are not met,

select another location.

• The location must be indoors and

must be free of airborne and other

contaminants.

• The location must not be near heat-

generating equipment or in direct

sunlight.

• The location must allow enough

clearance for water, drain, and electrical

connections in the rear of the ice

machine.

• The location must not obstruct airflow

through or around the ice machine.

Installation Requirements

• The ice machine and bin must be level.

• Vent the ice machine and bin drains

separately.

• Bin drain termination must have an air

gap.

• The ice machine and bin must be

descaled and sanitized after installation.

• The drain line must contain a union or

other suitable means of disconnection at

the ice machine.

QuietQube Models Only

• The ice machine top panel can be

trimmed with an aviator snips to allow

the line set, water line and electrical

connections to exit the top. Only cut out

what is needed, the back panel must

support the top panel.

• The water inlet and electrical connection

must contain a service loop to allow

future access.

Section 2

Installation

14 Part Number 000014141 Rev 07 2/20

Installation Section 2

Minimum/Maximum Temperatures

Model

Minimum Air

Temperature

Maximum Air

Temperature

All Ice

Machine

Head

Sections

35°F

2°C

110°F

43°C

Remote

Condensers

Minimum Air

Temperature

Maximum Air

Temperature

All Models

-20°F

-29°C

120°F

49°C

QuietQube

Condensing

Units

Minimum Air

Temperature

Maximum Air

Temperature

CVDF0600

CVDF0900

CVDT1200

CVDF2100

-20°F

-29°C

120°F

49°C

CVDF1400

CVDF1800

-20°F

-29°C

130°F

54°C

Ice Machine Heat of Rejection

Series

Air

Conditioning

Peak

IF0300

IT0300

4600 5450

IT0420 3800 6000

IT0450 3800 6000

IT0500 3800 6000

IF0500 3800 6000

IP0500 3800 6000

IP0520 3800 6000

IF0600 11800 13700

IT0620 5400 6300

IT0750 12800 13700

IF0900 13000 16000

IT0900 12700 14800

IT1200 16200 19100

IT1500 23000 27000

IT1900 26100 30500

Use this information when:

• Sizing air conditioning equipment where

self-contained air-cooled ice machines

are installed.

• Determining the load on a cooling tower.

Use the peak figure for sizing the load.

Part Number 000014141 Rev 07 2/20 15

Section 2 Installation

Clearance Requirements

IF0300

IT0300

Self-

Contained

Air-Cooled

Self-

Contained

Water-Cooled

Top/Sides 16" (40 cm) 8" (20 cm)

Back 5" (13 cm) 5" (13 cm)

IT0420 IT0620

Self-

Contained

Air-Cooled

Water-Cooled

or Remote

Condenser

Top/Sides 12" (31 cm) 8" (20 cm)

Back 5" (13 cm) 5" (13 cm)

IT0450 IT0500

IF0500 IP0500

IP0520 IF0600

IT0750 IF0900

IT0900

Self-

Contained

Air-Cooled

Self-

Contained

Water-Cooled

Top/Sides 8" (20 cm) 8" (20 cm)

Back 5" (13 cm) 5" (13 cm)

NOTE: Top air discharge kits require the

same clearance requirements as the

comparable self-contained air-cooled

model.

IT1200 60 Hz

Self-

Contained

Air-Cooled

Water-Cooled

or Remote

Condenser

Top/Sides 8" (20 cm) 8" (20 cm)

Back 5" (13 cm) 5" (13 cm)

IT1200 50 Hz

Self-

Contained

Air-Cooled

Water-Cooled

or Remote

Condenser

Top 12" (31 cm) 8" (20 cm)

Sides 23" (58 cm) 8" (20 cm)

Back 8" (20 cm) 5" (13 cm)

IT1500

Self-Contained

Air-Cooled

Water-Cooled

or Remote

Condenser

Top 12" (31 cm) 8" (20 cm)

Sides 8" (20 cm) 8" (20 cm)

Back 12" (31 cm) 5" (13 cm)

IT1900

Self-Contained

Air-Cooled

Water-Cooled

or Remote

Condenser

Top/Sides 24" (61 cm) 8" (20 cm)

Back 12" (31 cm) 5" (13 cm)

Bristol Compressor

1IT1900

Self-Contained

Air-Cooled

Water-Cooled

or Remote

Condenser

Top/Sides 8" (20 cm) 8" (20 cm)

Back 5" (13 cm) 5" (13 cm)

1Copeland Compressor

QuietQube Model Clearance Requirements

Model Top Back Sides

IF0600C

IT0750C

IF0900C

IT0900C

IT1200C

5"

(13 cm)

5"

(13 cm)

5"

(13 cm)

IBF0620C

IBF0820C

IBT1020C

IF1400C

IF1800C

IF2100C

2"**

(5 cm)

5"

(13 cm)

8" **

(20 cm)

** 24" (61 cm) is recommended on top/sides for

servicing

16 Part Number 000014141 Rev 07 2/20

Installation Section 2

Condensing Unit Clearance Requirements

Model Top/Sides Back Front

CVDF0600

CVDF0900

CVDT1200

CVDF1400

CVDF1800

CVDF2100

0"*

(0 cm)

48"

(122 cm)

48"

(122 cm)

* 24" (61 cm) is recommended on top/sides for

servicing

Notice

The ice machine must be protected if it

will be subjected to temperatures below

32°F (0°C). Failure caused by exposure to

freezing temperatures is not covered by

the warranty.

Air Baffle

Self-Contained Air-cooled Only

The air-cooled baffle prevents condenser

air from recirculating.

To install:

1. Loosen the back panel screws next to

the condenser.

2. Align the keyhole slots in the air baffle

with the screw holes and slide the

baffle down to lock in place.

Bin Installation Requirements

• The installation area must be capable of

supporting the combined weight of the

equipment and product.

• All ice machines installed on a bin

require an ice deflector.

• Manitowoc bins have a deflector

installed and require no modifications

when used with a forward-facing

evaporator.

• Ice machines with multiple evaporators

require a deflector kit.

• Align sides and back of ice machine with

sides and back of bin when placing ice

machine on bin.

• Optional sales kits are available to adapt

various sized or multiple ice machines on

large bins.

Part Number 000014141 Rev 07 2/20 17

Section 2 Installation

Bin Installation

NOTE: When using casters, the units must

be tethered or secured to comply with all

applicable codes. Swivel casters must be

mounted on the front and rigid casters

must be mounted on the rear. Lock the

front casters after installation is complete.

1. Remove threaded plug from drain

fitting.

2. Screw the leveling legs onto the

bottom of the bin.

3. Screw the foot of each leg in as far as

possible.

4. Move the bin into its final position.

5. Level the bin to assure that the bin

door closes and seals properly. Use a

level on top of the bin. Turn the base

of each foot as necessary to level the

bin.

6. Inspect bin gasket prior to ice machine

installation. (Manitowoc bins come

with a closed cell foam gasket installed

along the top surface of the bin.)

7. Remove all panels from ice machine

before lifting and installing on bin.

Remove front panel, top cover, left and

right side panels.

Dispenser Installation

Observe following recommendations unless

required by the dispenser manufacturer.

• An adapter is not required for ice

machines that match the dispenser size.

• A deflector is not required.

• Ice level management is recommended

to prevent water leakage or movement

of ice machine during agitation.

• Align sides and back of ice machine with

sides and back of dispenser when placing

ice machine.

• Follow ice machine installation

procedures in this manual and any

additional installation requirements

specified by the dispenser manufacturer.

18 Part Number 000014141 Rev 07 2/20

Installation Section 2

Electrical Requirements

All electrical work, including wire routing

and grounding, must conform to local, state

and national electrical codes. The following

precautions must be observed:

• The ice machine must be grounded.

• A separate fuse/circuit breaker

(dedicated circuit) must be provided

for each ice machine head section,

condenser or condensing unit.

• A qualified electrician must determine

proper wire size dependent upon

location, materials used and length of

run (minimum circuit ampacity can be

used to help select the wire size).

n

Warning

All wiring must conform to local, state and

national codes.

Voltage

The maximum allowable voltage variation

is +10% / -5% of the rated voltage at ice

machine start-up (when the electrical load

is highest).

n

Warning

The ice machine must be grounded

in accordance with national and local

electrical codes.

Fuse/Circuit Breaker

A separate electrical disconnect, which

disconnects all poles and has 3 mm (1/8")

contact separation, must be provided

for fixed wiring. Circuit breakers must be

H.A.C.R. rated in USA.

Minimum Circuit Ampacity

The minimum circuit ampacity is used to

help select the wire size of the electrical

supply. (Minimum circuit ampacity is not

the ice machine’s running amp load.)

The wire size (or gauge) also depends on

location, materials used, length of run, etc.,

so it must be determined by a qualified

electrician.

Ground Fault Circuit Interrupter

We do not recommend the use of a GFCI/

GFI circuit protection with our equipment.

If a GFCI/GFI is required by code, use a

GFCI/GFI breaker rather than an outlet,

which is more prone to intermittent

nuisance trips than panel circuit breakers.

Part Number 000014141 Rev 07 2/20 19

Section 2 Installation

Maximum Breaker Size & Minimum Circuit Amperage Chart

NOTE: Due to continuous product improvements, this information is for reference only.

Please refer to the ice machine data plate to verify electrical data. Model/Serial data plate

information overrides information listed on this page.

Ice

Machine

Voltage/Phase/

Cycle

Air-Cooled Water-Cooled Remote Condenser

Maximum

Fuse/Circuit

Breaker

Minimum

Circuit

Amps

Maximum

Fuse/Circuit

Breaker

Minimum

Circuit

Amps

Maximum

Fuse/Circuit

Breaker

Minimum

Circuit

Amps

IF0300

115/1/60 15 10.8 15 10.0 - - - - - -

230/1/50 15 6.1 15 5.6 - - - - - -

230/1/60 15 6.1 15 5.7 - - - - - -

IT0300

115/1/60 15 8.8 15 7.9 - - - - - -

230/1/50 15 4.2 15 3.8 - - - - - -

230/1/60 15 4.2 15 3.8 - - - - - -

IT0420

115/1/60 15 11.3 15 10.6 - - - - - -

208-230/1/60 15 5.5 15 5.2 - - - - - -

230/1/50 15 5.7 - - - - - - - - - - - -

IT0450

115/1/60 20 11.9 20 11.2 - - - - - -

208-230/1/60 15 5.6 15 5.3 - - - - - -

230/1/50 15 5.6 15 5.3 - - - - - -

IT0500

115/1/60 15 11.5 15 10.8 20

13.7

¹14.8

208-230/1/60 15 5.1 15 4.8 - - - - - -

230/1/50 15 5.6 - - - - - - - - - - - -

IF0500

115/1/60 - - - - - - - - - - - - 20 14.8

208-230/1/60 - - - - - - - - - - - - 15 11.7

IP0500

115/1/60 15 ¹11.5 - - - - - - - - - - - -

208-230/1/60 15 ¹5.1 - - - - - - - - - - - -

230/1/50 15 ¹5.6 - - - - - - - - - - - -

IP0520

115/1/60 15 ¹11.5 - - - - - - - - - - - -

208-230/1/60 15 ¹5.1 - - - - - - - - - - - -

230/1/50 15 ¹5.6 - - - - - - - - - - - -

IF0600

208-230/1/60 15 11.1 15 10.7 15

11.7

¹8.9

230/1/50 15 6.7 15 6.1 15

7.1

18.1

IT0620

115/1/60 20 12.2 20 11.6 - - - - - -

208-230/1/60 15 5.9 15 5.6 - - - - - -

230/1/50 15 5.6 15 5.4 - - - - - -

20 Part Number 000014141 Rev 07 2/20

Installation Section 2

Ice

Machine

Voltage/Phase/

Cycle

Air-Cooled Water-Cooled Remote Condenser

Maximum

Fuse/Circuit

Breaker

Minimum

Circuit

Amps

Maximum

Fuse/Circuit

Breaker

Minimum

Circuit

Amps

Maximum

Fuse/Circuit

Breaker

Minimum

Circuit

Amps

IT0750

208-230/1/60 15

8.4

¹8.3

15

8.1

¹7.9

- - - - - -

230/1/50 15

8.4

¹6.7

15

8.1

¹6.5

- - - - - -

IF0900

208-230/1/60

20

15

12.2

¹9.5

20

11.2

¹8.8

20

15

12.2

¹9.8

208-230/3/60 15 9.7 15 8.7 15

9.7

¹7.2

230/1/50 15 8.9 15 8.2 15

8.6

19.0

IT0900

208-230/1/60 15 9.5 15 8.8 - - - - - -

230/1/50 15 10.7 15 10.1 - - - - - -

IT1200

208-230/1/60 20 14.2 20 13.4 15

11.0

¹10.9

208-230/3/60 15 8.6 15 7.9 15

9.2

110.1

230/1/50 20 14.0 20 13.3

15

25

11.1

115.6

IT1500

208-230/1/60

25

30

15.4

¹18.5

25

30

14.0

¹17.0

25

14.0

¹15.6

208-230/3/60 20

12.8

113.4

20

11.3

112.0

20

25

20

11.3

115.3

113.0

230/1/50

25

20

14.9

114.3

25

20

14.2

113.5

25

20

15.2

114.6

IT1900

208-230/1/60 30

17.9

120.1

25

30

16.5

¹15.0

118.8

25

30

17.0

¹18.5

119.3

208-230/3/60 20

14.2

114.4

20

12.8

113.0

20

13.0

113.1

230/1/50 25

15.8

116.5

25 15.0 25

15.3

115.8

380-460/3/50-60 - - - - - - 15 6.1 - - - - - -

¹Alternate compressor - Refer to model serial tag on ice machine to verify your minimum circuit amps.

Page is loading ...

Manitowoc Ice D400 Bin Installation guide

Manitowoc Ice D400 Bin Installation guide

Related papers

Other documents