SANDVIK Silent Tools ST+:BT A 1PP User manual

Brand: SANDVIK

Model: Silent Tools ST+:BT A 1PP

Type: User manual

This manual is also suitable for

SANDVIK Silent Tools ST+:BT A 1PP is a device which provides a digital link between the Silent Tools™ Plus Turning adaptor and the Silent Tools™ Plus software. It is suitable for use under rough conditions and not suitable for use in aggressive or explosive environments. The electronic unit has a connector for cable, vibration, and one optional connector for cable, load. It also has an antenna lid for Bluetooth antenna, and a battery slot for Type-A Li-ion battery. The Bluetooth range depends on the distance between tool and PC (normal range is 10 m) and the presence of any obstacles in between them.

Version 1.1

User manual

Silent Tools™ Plus Electronic unit

ST+:BT A 1PP

ST+:BT A 2PP

may not be copied or reproduced in whole or in part, or transferred to

any other media or language, by any means, without the prior written

permission of Sandvik Coromant AB.

Introduction

Purchase

Congratulations on your purchase of a Silent Tools™ Plus Electronic

unit.

This manual contains important safety directions and instructions for

product set-up and operation.

Keep for further reference

Product identification

Product type and article numbers are printed on the product. Refer to

this when contacting Sandvik Coromant.

Validity of this manual

This manual applies to the Silent Tools™ Plus Electronic units:

Model Art. No. Spare part No.

ST+: BT A 1PP 157434 7210 110-01

ST+: BT A 2PP 160953 7210 110-02

Available documents

Silent Tools™ Plus Electronic unit user manual and other documents

can be downloaded from the Sandvik Coromant website:

http://www.sandvik.coromant.com

Content

1 Safety .................................................................................. 1

1.1 General 1

1.2 Purpose 3

1.3 Hazard of use 5

1.4 Disposal 6

2 Silent Tools™ Plus system ...................................... 7

2.1 Electronic unit 9

3 Operation ........................................................................11

3.1 Mounting of the electronic unit 11

3.2 Connecting the electronic unit 12

3.3 Operating procedure 16

3.4 Function lights 18

4 Care and transport ................................................... 20

4.1 Transport 20

4.2 Storage 20

4.3 Cleaning and drying 20

5 Conformity .................................................................... 21

5.1 Simplied EU Declaration of conformity 21

5.2 Simplied sDoC, USA 21

5.3 Canada 23

6 Warranty ......................................................................... 24

7 Technical data ............................................................. 25

1 Safety

1.1 General

Description

The following instructions should enable the person responsible for

the product and the person who actually uses the equipment to antic-

ipate and avoid operational hazards. The person responsible for the

product must ensure that all users understand these instructions and

adhere to them.

About warning messages

Warning messages are an essential part of product safety. They

appear wherever hazards or hazardous situations can occur.

For user safety, all safety instructions and safety messages shall be

strictly observed and followed. Therefore, the manual must always be

available to all product users.

DANGER, WARNING, CAUTION and NOTICE are standardized signal

words for identifying levels of hazards and risks related to personal

injury and property damage. For your safety it is important to read

and fully understand the table below with the different signal words

and their definitions. Supplementary safety information symbols

may be placed within a warning message as well as supplementary

information.

DANGER Indicates an imminently hazardous

situation which, if not avoided, will result

in death or serious injury.

WARNING Indicates a potentially hazardous

situation or an unintended use which,

if not avoided, could result in death or

serious injury.

CAUTION Indicates a potentially hazardous

situation or an unintended use which,

if not avoided, may result in minor or

moderate injury.

NOTICE Important information which must be

adhered to in practice as it enables

the product to be used in a technically

correct and efficient manner.

1.2 Purpose

Permitted use

The electronic unit provides a digital link between the Silent Tools™

Plus Turning adaptor and the Silent Tools™ Plus software.

Adverse use

• Use of the product without instruction.

• Use outside of the intended limits.

• Disabling safety systems.

• Removal of hazard notices.

• Opening the product using tools, e.g. screwdriver.

• Modication or conversion of the product.

• Use after misappropriation.

• Use of products with obviously recognizable damages or defects.

• Use with accessories from other manufacturers without the prior

explicit approval of Sandvik Coromant.

WARNING

Adverse use can lead to injury, malfunction and damage. It is the

task of the person responsible for the equipment to inform the user

about hazards and how to counteract them. The product is not to be

operated until the user has been instructed on how to work with it.

Manufacturer of the product

Sandvik Coromant is responsible for supplying the product, including

the user manual and original accessories, in a completely safe

condition.

The Silent Tools™ Plus product, including electronic hardware, is

intended to be used in the country Sandvik Coromant puts it on the

market. Sandvik Coromant takes no responsibility for the product’s

conformity with any laws and/or regulations outside the country it

was put on the market.

If any export of products after receipt from Sandvik Coromant is

intended, the customer takes the full responsibility to ensure that the

product and the intended use are in conformity with all applicable

laws and regulations within that country.

Manufacturers of non-Sandvik Coromant

Accessories

The manufacturers of non-Sandvik Coromant accessories are

responsible for developing, implementing and communicating safety

concepts for their products, and are also responsible for the effec-

tiveness of those safety concepts in combination with the Sandvik

Coromant product.

Person in charge of the product

NOTICE

The person in charge of the product has the following duties:

• To understand the safety instructions on the product and the

instructions in the user manual.

• To be familiar with local regulations relating to safety and accident

prevention.

• To inform Sandvik Coromant immediately if the product becomes

unsafe.

1.3 Hazard of use

Environment

Suitable for use under rough conditions, see section “7 Technical

data”. Not suitable for use in aggressive or explosive environments.

CAUTION

Avoid high temperature, above rating, while using the electronic unit,

the battery (e.g. do not let hot metal chips directly hit the battery or

the electronic unit). This may cause the function of the electronic unit

to end prematurely or cause a damage to the battery.

Precautions: Do not open the product. Only Sandvik Coromant

authorized service workshops are entitled to repair these products.

NOTICE

Should an operational error or unexpected change in the perfor-

mance occur during use; disconnect the battery and contact the

supplier.

1.4 Disposal

Dispose of the product appropriately in accordance with the national

regulations in force in your country.

At the end of their service life electric and electronic equipment and

their accessories shall not be discarded with the municipal waste

but be disposed of using separate collection, treatment, recovery/

recycling and environmentally sound disposal.

Precautions: Product specific treatment and waste management

information can be downloaded from the Sandvik Coromant home

page at www.sandvik.coromant.com/services or received from your

Sandvik Coromant dealer.

2 Silent Tools™ Plus system

The Silent Tools™ Plus system is intended for remote monitoring of

the machining process .

Component Description

1Electronic unit • Provides a link to the turning adaptor,

through the connecting cable, type PP

(push-pull).

• Provides communication to/from the

sensor(s) in the turning adaptor.

• Provides power to the sensor(s) and the

transmitter.

• Transmits the signal to the tablet.

2Turning adaptor

(ordered

separately)

• Holder for a cutting head, intended for metal

cutting.

• Consists of various models with a range of

sizes in diameter, length and cutting head

interfaces.

• Integrated with sensor(s).

3Connecting

cable

• Connecting the electronic unit to the turning

adaptor.

• Cable with PP type connectors (push-pull).

• Length 300 mm or 500 mm.

4Battery • Type-A Li-ion.

5Cover plug • Protects the battery connection in the

electronic unit when battery is not inserted.

6User manuals • Silent Tools™ Plus Electronic unit

• Silent Tools™ Plus Turning adaptor

• Silent Tools™ Plus A Bat9.6Wh

2.1 Electronic unit

The electronic unit is designed to provide a link between the Silent

Tools™ Plus Turning adaptor and the Silent Tools™ Plus software.

The family names of compatible turning adaptors are TB60D- or

TB61D- and the signal connection type position in the product code

must be B or C.

Example:

TB60D-CY60B810W4LB

TB61D-CY100C1770W4RB

Silent Tools™ Plus engineered solutions may use one or two PP

connectors, depending on the tool mounted to it.

Model ST+:BT A 1PP ST+:BT A 2PP

Sensor 1, vibration B √ √

Sensor 2, load C X √

Component Description

1Connector Connector for cable, vibration.

2Connector Connector for cable, load (optional).

3Antenna lid Lid for Bluetooth antenna.

4Battery Type-A Li-ion.

5User manual

3 Operation

3.1 Mounting of the electronic unit

The electronic unit should be mounted on the tool post before use.

The tool post needs to be modified to allow for the mounting of the

electronic unit.

The Bluetooth antenna must point towards the operator when

positioning the electronic module. This area must not be blocked by

metal, in order to ensure proper signal range. The signal penetrates

through a closed machine, via the glass and gaps.

Bluetooth range depends on the distance between tool and PC

(normal range is 10 m) and the presence of any obstacles in between

them.

Make sure the location of the electronic unit allows for easy battery

insertion and removal. The electronic unit should be mounted

horizontally (central axis of battery) with screws in the six holes,

diameter 5 mm.

3.2 Connecting the electronic unit

Connect the cables between the electronic unit and the turning

adaptor. Insert battery to power up the electronic unit and sensors in

the turning adaptor.

NOTICE

The transmitter will always transmit a signal when the battery is

inserted, until the electronics disconnect the battery. This happens

when a low voltage threshold is reached. The threshold level is set

to be safe for the battery. The electronics power up again when a

charged battery is inserted.

To shut off the electronic unit, remove the battery.

NOTICE

Remove the battery if the electronic unit will not be used for a long

period of time. Mount the cover plug on the electronic unit to protect

the battery connector. Refer to section “7 Technical data” for infor-

mation on voltage, rated power and operating time.

Connecting cables

Install cables carefully to avoid sharp bends. Do not overbend the

cables, they may be damaged. Make sure the cables are not damaged

by moving/rotating parts of the lathe-/turn-mill centre and that no

weight is placed on top of them.

√ X

Orient the cable as indicated by the groove in the connector or the

N-mark. Push the cable straight into the connector.

NOTICE

Make sure not to rotate the cable during the push-pull movement.

Remove the cable by a pull. Grip the connector, not the cable, when

pulling.

√ X

Inserting battery

1. Orient the battery according to the position slot and insert the

battery into the electronic unit.

2. A soft click indicates when assembly is complete.

Page is loading ...

SANDVIK Silent Tools ST+:BT A 1PP User manual

Brand: SANDVIK

Model: Silent Tools ST+:BT A 1PP

Type: User manual

This manual is also suitable for

Download PDF

report

SANDVIK Silent Tools ST+:BT A 1PP User manual

This manual is also suitable for

SANDVIK Silent Tools ST+:BT A 1PP User manual

Other documents