Procentec ProfiHub A5 User manual

Brand: Procentec

Model: ProfiHub A5

Type: User manual

This manual is also suitable for

Profihub B5

ProfiHub A5/B5 User Manual

_______________________________________________

Version 2.1.1 – June 2014 Page 1 / 59

User Manual

ProfiHub A5/B5

5 Channel DP Spur and Repeater component

5 Isolated Channels.

Transparent for all PROFIBUS DP protocols.

RS 485 specifications for each channel.

Max. 12 Mbps.

Max. 31 devices per channel.

Max. 1200 m spur line length.

No limit in serial placement.

No address required.

Integrated termination facilities.

Configurable grounding system.

IP 65 classification (ProfiHub A5).

IP 20 classification (ProfiHub B5).

ProfiHub A5/B5 User Manual

_______________________________________________

Version 2.1.1 – June 2014 Page 2 / 59

Safety Guidelines

This manual contains notices which you should observe to ensure your own personal safety, as well

as to protect the product and connected equipment. These notices are highlighted in the manual by a

warning sign and are marked as follows according to the level of danger:



Draws your attention to important information on handling the product, a particular part of the

documentation or the correct functioning of the product.

Warning

This device and its components may only be used for the applications described in this manual and

only in connection with devices or components that comply with PROFIBUS and an RS 485 interface.

This product can only function correctly and safely if it is transported, stored, set up, installed,

operated and maintained as recommended.

Qualified Technicians

Only qualified technicians should be allowed to install and work with this equipment. Qualified

technicians are defined as persons who are authorized to commission, to ground, to tag circuits and

systems in accordance with established safety practices and standards. It is recommended that the

technicians carry a Certified PROFIBUS Installer or Certified PROFIBUS Engineer certificate.

Disclaimer of Liability

We have checked the contents of this manual as much as possible. Since deviations cannot be

precluded entirely, we cannot guarantee full agreement. However, the content in this manual is

reviewed regularly and any necessary corrections included in subsequent editions. Suggestions for

improvement are welcomed.

transmitted, in any form or by any means, electronic, mechanical, photocopying, recording or

otherwise, without the prior written permission of the publisher.

PROCENTEC

Klopperman 16

2292 JD WATERINGEN

The Netherlands

Tel.: +31-(0)174-671800

Fax: +31-(0)174-671801

Email: info@procentec.com

Web: www.procentec.com

ProfiHub A5/B5 User Manual

_______________________________________________

Version 2.1.1 – June 2014 Page 3 / 59

Important Information

Purpose of the Manual

This manual explains how to put the ProfiHub A5 and ProfiHub B5 into operation.

Recycling and Disposal

The parts of the ProfiHub can be recycled. For further information about environment-friendly recycling

and the procedure for disposing your old equipment, please contact:

PROCENTEC

Klopperman 16

2292 JD WATERINGEN

The Netherlands

Tel.: +31-(0)174-671800

Fax: +31-(0)174-671801

Email: info@procentec.com

Document Updates

You can obtain constantly updated information on PROCENTEC products on the Internet at

www.procentec.com

You can also contact PROCENTEC Customer Support:

- by phone at +31-(0)174-671800

- by fax at +31-(0)174-671801

- by email at support@procentec.com

ProfiHub A5/B5 User Manual

_______________________________________________

Version 2.1.1 – June 2014 Page 4 / 59

Contents

1 Product Description ...................................................................................................................... 5

1.1 Product Features .................................................................................................................... 6

1.2 Application areas .................................................................................................................... 7

1.3 Additional Benefits ................................................................................................................. 7

1.4 Channel Structure .................................................................................................................. 8

1.5 Grounding System ................................................................................................................. 8

1.6 Cable lengths for PROFIBUS DP........................................................................................... 9

1.7 Cable types for PROFIBUS DP............................................................................................ 10

1.8 Status Display ...................................................................................................................... 11

1.9 Comparison table ................................................................................................................. 12

2 Installation Instructions ProfiHub A5 ....................................................................................... 26

2.1 Location ................................................................................................................................ 26

2.2 Position ................................................................................................................................. 26

2.3 Mounting ............................................................................................................................... 26

2.4 Power Supply ....................................................................................................................... 27

2.5 Backbone ............................................................................................................................. 28

2.6 Spur Segments..................................................................................................................... 29

2.7 Termination .......................................................................................................................... 30

2.8 Baudrate switch .................................................................................................................... 31

3 Installation Instructions ProfiHub B5 ....................................................................................... 32

3.1 Location ................................................................................................................................ 32

3.2 Position ................................................................................................................................. 32

3.3 Mounting ............................................................................................................................... 32

3.4 Power Supply ....................................................................................................................... 32

3.5 Backbone ............................................................................................................................. 33

3.6 Spur Segments..................................................................................................................... 34

3.7 Termination .......................................................................................................................... 35

3.8 Baudrate switch .................................................................................................................... 36

4 Technical Data ProfiHub A5 ....................................................................................................... 37

5 Technical Data ProfiHub B5 ....................................................................................................... 39

6 Sales offices and Distributors ................................................................................................... 41

7 Order codes ................................................................................................................................. 41

8 Glossary ....................................................................................................................................... 47

9 Certificates .................................................................................................................................. 50

10 Revision History .......................................................................................................................... 53

11 Next version ................................................................................................................................ 54

12 Notes ............................................................................................................................................ 55

ProfiHub A5/B5 User Manual

_______________________________________________

Version 2.1.1 – June 2014 Page 5 / 59

1 Product Description

ProfiHub A5 and B5 are advanced, flexible

and robust network components for

PROFIBUS DP installations, to implement

long multi-device spur lines and backbone

structures with star/tree segments.

PROFIBUS DP is a high speed communication

bus that has to comply with strict rules

concerning spur lines, because of possible

reflections that could lead to communication

disturbances. If spur lines or star segments are

required, costly investments in repeaters have

to be done.

Innovative components for such applications are

the ProfiHub A5 and B5. These are perfect

economic solutions to implement reliable spur

lines in high speed DP networks. They have the

functionality of 5 galvanic isolated transparent

repeaters. This allows network structures with

extended spur lines that individually can handle a

maximum of 31 devices and a length equal to the

main bus. The ProfiHub A5 and B5 refresh a

received message on one Channel and

transfer it to all the other Channels (chicken

foot topology).

Because the ProfiHub A5 and B5 create isolated

segments, the devices can now be removed and

added during operation. Also electrical bus

problems and EMC disturbances in a spur do not

spread to the other segments. The intelligent

logic and isolation circuits of the ProfiHubs do not

change the bit width. This means the ProfiHubs

do not have limitations in serial placement. The

logic also detects the transmission speed

automatically.

To assist the installation work, termination is

integrated and can be switched on/off. The

grounding concept is also selectable: direct or

capacitive grounding. The ProfiHubs are powered by a 10 to 32 DC Voltage (110/230V AC versions

are also available). For troubleshooting, maintenance and commissioning the ProfiHubs are equipped

with a display on the outside, which indicate the status of each Channel (Data and Error).

Fig. 1 - ProfiHub A5 (IP65)

Fig. 2 - ProfiHub B5 (IP20)

ProfiHub A5/B5 User Manual

_______________________________________________

Version 2.1.1 – June 2014 Page 6 / 59

1.1 Product Features

 5 Galvanic isolated channels (repeater

segments).

 Transparent for all PROFIBUS DP

protocols.

 DP - RS 485 specifications for each

channel.

 9,6 Kbps to 12 Mbps.

 31 devices per channel.

 1200 m spur line length (depends on

transmission speed).

 No limit in serial placement or cascading of

ProfiHubs.

 No address required.

 Integrated termination facilities (switches).

 Configurable grounding system (direct or capacitive).

 IP 65 classification (ProfiHub A5).

 IP 20 classification (ProfiHub B5).

Fig. 3 - Long spur lines to instruments and the possibility to remove/insert them during

operation. Short circuit protection on each spur line is automatically provided.

ProfiHub A5/B5 User Manual

_______________________________________________

Version 2.1.1 – June 2014 Page 7 / 59

1.2 Application areas

 Dynamic spur lines to actuators, flow meters and pH analyzers.

 Removable drives and motors.

 Pull/Plug motor control centers (drawers).

 Roof mounted devices in tank farms.

 Dirty and humid environments.

 Barrier for non galvanic isolated equipment.

 Large star/tree structured networks.

 Outdoor applications with device and cable stress (ProfiHub A5).

1.3 Additional Benefits

 Hot slave insertion and removal during operation.

 Short circuit protection on each Channel.

 Compact and robust construction.

 Status and error display (per Channel).

 Suitable for all DP cables.

 Conveniently arranged networks.

 Easy extendable installations.

 Standard glands can be replaced with M12 (ProfiHub A5).

 On-board DB9 female connector for maintenance activities (ProfiHub A5).

 Cost Savings.

Fig. 4 - Because of the isolation and intelligence the ProfiHub provides, it can be used as

a barrier for electrically sensitive segments. This keeps the backbone and other

Channels clean.

ProfiHub A5/B5 User Manual

_______________________________________________

Version 2.1.1 – June 2014 Page 8 / 59

1.4 Channel Structure

Every Channel is electrically isolated and internally connected to the transparent intelligent backbone.

The termination is switchable and powered by the ProfiHub. The shielding of the PROFIBUS cable can

be directly grounded or indirectly grounded (see the next paragraph).

1.5 Grounding System

The ProfiHubs can be grounded by 3 methods:

1) Direct grounding

2) Indirect grounding (through a capacitor)

3) Combination of direct and indirect.

In most cases it is recommended always to use Direct Grounding with the power supply and the

shielding of the PROFIBUS cables. If you do not want to ground all or some cables to the common

ground, the cable shielding should be connected to pin ‘I’. A capacitor with a parallel high value

resistor will separate the 2 potentials (Fig. 5).

If by accident on 1 channel the Direct Grounding is connected with the Indirect Grounding, the Direct

Grounding “wins”.

Fig. 5 - Channel structure

ProfiHub A5/B5 User Manual

_______________________________________________

Version 2.1.1 – June 2014 Page 9 / 59

1.6 Cable lengths for PROFIBUS DP

The cables on the Channels and the Main-Channel should comply with the PROFIBUS DP cable

specifications for RS 485 (Fig. 6).

Fig. 6 - Cable lengths for PROFIBUS DP

ProfiHub A5/B5 User Manual

_______________________________________________

Version 2.1.1 – June 2014 Page 10 / 59

1.7 Cable types for PROFIBUS DP

The cable type should comply with the PROFIBUS DP cable specifications for RS 485 (Fig. 7).

The ProfiHub A5 can handle cables based on multiple protection sheaths with a diameter between 6 to

12 mm (Fig. 8).

Parameter

Value

Wires

2 (twisted)

Impedance

135 .. 165 Ohm at 3 to 20 MHz

Capacity

< 30 pF/m

Loop resistance

< 110 Ohm/km

Wire diameter

> 0.64 mm

Wire area

> 0.32 mm

FRNC cable

Shipboard cable

Festoon cable

Flexible cable

Food cable

Robust cable

Trailing cable

Hybrid cable

Fig. 8 - Cables with different protection sheaths.

Fig. 7 - PROFIBUS DP cable specifications

ProfiHub A5/B5 User Manual

_______________________________________________

Version 2.1.1 – June 2014 Page 11 / 59

1.8 Status Display

The Status Display on the ProfiHubs is very useful for diagnostics.

OFF

Blinking

POWER

 Power is not

switched on or an

internal failure.

 Power supply not

stable or an internal

failure.

 Power supply OK.

Main READY

 Power is not

switched on or an

internal failure.

 Trying to detect the

transmission speed, but

has not locked it yet.

 The transmission

speed has been

detected.

Main RX-OK

 No communication

detected on the Main-

Channel.

 1 or more devices

communicating on the

Main-Channel.

 1 or more devices

communicating on the

Main-Channel.

Main ERROR

 No problem has

been detected.

 Problem in the

cabling has been

detected (Main

Channel).

 Problem in the

cabling has been

detected (Main

Channel).

Channel RX-OK

 There is no

communication

detected (on this

Channel).

 1 or more devices

communicating (on this

Channel).

 1 or more devices

communicating (on this

Channel).

Channel ERROR

 No problem has

been detected.

 Problem in the

cabling has been

detected (on this

Channel).

 Problem in the

cabling has been

detected (on this

Channel).

ProfiHub A5/B5 User Manual

_______________________________________________

Version 2.1.1 – June 2014 Page 12 / 59

1.9 Comparison table

ProfiHub A5

ProfiHub B5

Area

IP 65

IP 20

Housing

Plastic

Metal

Mounting

Corner screws

DIN-rail

Weight

800 g

650 g

Dimensions

213 x 210 x 95 mm

167 x 111 x 32 mm

PROFIBUS connectors

Screw terminals (inside)

Glands (outside)

Screw terminals and DB9

connectors

Alternative connectors

Glands can be replaced with M12

connectors (see chapter 0

2 Sales offices and

Distributors

HEADQUARTERS

PROCENTEC T: +31-(0)174-671800

Klopperman 16 F: +31-(0)174-671801

2292 JD WATERINGEN E:

fo@procentec.com

Netherlands I: www.procentec.com

ARGENTINA

eFALCOM T: +54 237 46 31 151

Alcorta 2411 F: +54 237 46 31 150

B1744 - Moreno E:

antiago.falc[email protected]

Buenos Aires I: www.efalcom.com.ar

Argentina

AUSTRALIA

IS Systems Pty Limited T: +61 2 4964 8548

14 Laverick Ave., F: +61 2 4964 8877

Tomago E:

itz.woller@issystems.com.au

NSW, Australia, 2322 I: www.issystems.com.au

Pentair Flow Control Pacific T: +61 2 4448 0466

1 Percival Road F: +61 2 4423 3232

Smithfield E:

haree.haze[email protected]

NSW, Australia, 2164 I: www.profibuscentre.com.au

BELGIUM and LUXEMBOURG

 
 
ProfiHub A5/B5 User Manual 
 
 
 
 _______________________________________________ 
          Version 2.1.1 – June 2014  Page 13 / 59 
ProfiHub-A5B5-Manual-EN  © PROCENTEC 2005-2014 - Copyright - all rights reserved 
Bintz Technics N.V.  T:  +32 2 720 49 16 
Brixtonlaan 23  F:  +32 2 720 37 50 
B-1930 Zaventem  E: 
  bl
oemen@bintz.be 
Belgium  I:  www.bintz.be 
BRAZIL 
Westcon Instrument. Indl Ltda  T:  +55 11 5561-7488 
Rual Alvaro Rodrigues, 257  F:  +55 11 5093-2592 
São Paulo – SP  E: 
  p
[email protected]m.br 
Brazil - CEP 04582-000  I:  www.wii.com.br 
CANADA 
Streamline Process Management Inc.  T:  +1 403 225 1986 
#3, 4351 – 104 Ave SE  F:  +1 587 585 2828 
Calgary, Alberta T2C 5C6  E: 
  a
dmin@streamlinepm.com 
Canada  I:  www.streamlinepm.com 
CHILE 
RP Ingenieria Limitada  T:  +56-(0)41-2469350 
Tucapel 92 oficina 52  F:  +56-(0)41-2522592 
Concepción  E: 
  r
odrigopint[email protected] 
Chile  I:  www.rpingenieria.cl 
CHINA 
PROCENTEC Beijing  T:  +86(10)84766911 or 84787311 
Room E-1115 WangJingYuan YouLeHui  F:  +86(10)84766722 
ChaoYang  E: 
  in
fo@procentec.net 
Beijing  I:  www.procentec.net 
China 
CZECH REPUBLIC 
FOXON s.r.o.  T:  +420 484 845 555 
Polní 367  F:  +420 484 845 556 
460 01 Liberec 12  E: 
  f
[email protected]z 
Czech Republic  I:  www.foxon.cz 
 
DENMARK 
ProSaiCon  T:  +45 70 20 52 01  
Jernbanegade 23B  F:  +45 70 20 52 02 
DK 4000 Roskilde  E: 
  h
fj@prosaicon.dk 
Denmark  I:  www.prosaicon.dk 
EGYPT 
Mas Trading  T:  +2 02 2524 2842 
37, 105 Street  F:  +2 02 2524 2843 
Al-Etihad Square  E: 
  a
ya.elshafe[email protected] 
Egypt  I:  www.masautomation.com 
ESTONIA 

 
 
ProfiHub A5/B5 User Manual 
 
 
 
 _______________________________________________ 
          Version 2.1.1 – June 2014  Page 14 / 59 
ProfiHub-A5B5-Manual-EN  © PROCENTEC 2005-2014 - Copyright - all rights reserved 
Saksa Automaatika OU  T:  +372 605 2526 
Peterburi Tee 49  F:  +372 605 2524 
Tailinn  E: 
  in
fo@saksa-automaatika.ee 
EE-11415 Estonia  I:  www.saksa-automaatika.ee 
FINLAND 
Hantekno Oy  T:  +358 40 8222 014 
Kalliotie 2  E: 
  in
fo@hantekno.com 
04360 Tuusula  I:  www.hantekno.fi 
Finland   
FRANCE 
AGILiCOM  T:  +33 247 76 10 20 
Bâtiment B  F:  +33 247 37 95 54 
1, rue de la Briaudière  E: 
  jy
.bois@agilicom.fr 
Z.A. La Châtaigneraie  I:  www.agilicom.fr 
37510 BALLAN-MIRE   
France   
GERMANY 
PROCENTEC GmbH  T:  +49-(0)721 831 663-0 
Benzstrasse 15  F:  +49-(0)721 831 663-29 
D-76185 Karlsruhe  E: 
  in
fo@procentec.de 
Germany  I:  www.procentec.de  
INDIA 
UL Engineering Services & Software Pvt Ltd  T:  +91-202 696 0050 
Nirman Classic,  F:  +91-202 696 2079 
Katraj-Kondhwa Road,  E: 
  di
leep.miski[email protected]m 
Katraj, Pune-411046   I:  www.ulepl.com 
India 
IRELAND 
PROFIBUS Ireland  T:  +353-61-202107 or +35361240240 
Automation Research Centre  F:  +353-61-202582 
University of Limerick  E: 
  in
fo@profibus.ie 
National Technology Park, Plassey  I:  www.profibus.ie 
Limerick 
Ireland   
ISRAEL 
Instrumetrics Industrial Control  T:  +972-9-8357090 
8 Hamlacha St.  F:  +972-9-8350619 
New Industrial Zone  E: 
  in
fo@instrumetrics-ic.co.il 
Netanya, 42170   I:  www.inst-ic.co.il 
Israel 
ITALY 
PROCENTEC Italy  T:  +39 030 200 8610 
Via Branze n. 43/45  F:  +39 030 238 0059 
25123 Brescia  E: 
  w

 
 
ProfiHub A5/B5 User Manual 
 
 
 
 _______________________________________________ 
          Version 2.1.1 – June 2014  Page 15 / 59 
ProfiHub-A5B5-Manual-EN  © PROCENTEC 2005-2014 - Copyright - all rights reserved 
ww.procentec.it 
Italy 
 
W:
  w
ww.procentec.it 
 
 
Genoa FIELDBUS Competence Centre Srl  T:  +39 010 86 02 580 
Via Greto di Cornigliano, 6R/38  F:  +39 010 65 63 233 
16152 Genova  E: 
  p
rocentec@gfcc.it 
Italy
 
W:
  w
ww.gfcc.it 
JAPAN 
TJ Group  T:  +81-3-6450-3739 
C/O Japanese PROFIBUS Organisation  F:  +81-3-6450-3739 
West World Building 4F  E: 
  in
fo@profibus.jp 
3-1-6 Higashi-Gotanda,   
Shinagawa-ku, 
Tokyo, 141-0022   
Japan 
KOREA 
Hi-PRO Tech. Co., Ltd.  T:  +82 82-31-216-2640 
#2802, U-Tower, 1029   F:  +82 82-31-216-2644 
Youngduk-dong, Giheung-gu  E: 
  c
hays@hiprotech.co.kr 
Yongin-Si, Kyunggi-do,  I:  www.profibus.co.kr 
446-908 Korea 
LEBANON 
Industrial Technologies S.A.L. (ITEC)  T:  +961 1 491161 
Point Center, Boulevard Fouad Chehab  F:  +961 1 491162 
Sin El Fil  E: 
  s
ales@iteclb.com 
Beirut  I:  www.iteclb.com 
Lebanon 
MEXICO 
Grid Connect Inc.   T:  +1 530-219-2565 (Spanish) 
  E: 
  t
omf@gridconnect.com 
  I:  www.gridconnect.com 
NETHERLANDS 
PROCENTEC B.V.  T:  +31 (0)174 671800 
Klopperman 16  F:  +31 (0)174 671 801 
2292 JD Wateringen  E: 
  in
fo@procentec.com 
Netherlands  I:  www.procentec.com 
NORWAY 
AD Elektronikk AS  T:  +47 64 97 60 60 
Boks 641  F:  +47 64 97 60 70 

 
 
ProfiHub A5/B5 User Manual 
 
 
 
 _______________________________________________ 
          Version 2.1.1 – June 2014  Page 16 / 59 
ProfiHub-A5B5-Manual-EN  © PROCENTEC 2005-2014 - Copyright - all rights reserved 
N-1401 SKI  E: 
  k
[email protected] 
Norway  I:  www.ade.no 
PERU 
ControlWare  T:  +51 1637 3735 
Jr. Los Silicios 5409  F:  +51 1528 0454 
Los Olivos - L39  E: 
  in
fo@controlware.com.pe 
Peru  I:  www.controlware.com.pe 
POLAND 
INTEX Sp. z o.o.  T:  +48 32 230 75 16 
ul. Portowa 4  F:  +48 32 230 75 17 
44-102 Gliwice  E: 
  in
[email protected]om.pl 
Poland  I:  www.intex.com.pl 
ROMANIA 
S.C. SVT Electronics S.R.L.  T:  +40 365 809 305 
Brǎila 7  F:  +40 365 809 305 
540331 Tg-Mure  E: 
  s
ajgo.tibor@svt.ro 
Romania  I:  www.svt.ro 
 
 
 
 
 
SAUDI ARABIA 
ASM Process Automation  T:  +966 2 691 2741 
Al-Zahra Dist. – Attas st.  F:  +966 2 682 8943 
cross section with helmy Kutby St.  E: 
  in
fo@asmestablishment.com 
Villa no.25  I:  www.asmestablishment.com 
Jeddah-21553   
Saudi Arabia 
SINGAPORE / SOUTH EAST ASIA 
Allegro Electronics  T:  +65 62878063 
236 Serangoon Avenue 3 07-98  E:  sales@allegro.com.sg 
Singapore 550236  I:  www.allegro.com.sg 
SLOVAKIA 
ControlSystem s.r.o.  T:  +421 486115900 
Stúrova 4  F:  +421 486111891 
977 01 BREZNO  E: 
  ja
n.snopko@controlsystem.sk 
Slovakia  E: 
  ja
n.snopko@controlsystem.sk 
SOUTH AFRICA 
IDX ONLINE CC  T:  +27(11) 548 9960 
1 Weaver Street   F:  +27(11) 465-8890 
Fourways  E: 
  s
ales@idxonline.com 
Johannesburg  I:  www.idxonline.com 

 
 
ProfiHub A5/B5 User Manual 
 
 
 
 _______________________________________________ 
          Version 2.1.1 – June 2014  Page 17 / 59 
ProfiHub-A5B5-Manual-EN  © PROCENTEC 2005-2014 - Copyright - all rights reserved 
South Africa - 2191 
SPAIN 
LOGITEK, S.A  T:  +34 93 588 6767 
Ctra. de Sant Cugat, 63 Esc. B Planta 1ª  E: 
  x
avier.cardena@logitek.es 
Rubí (BARCELONA), 08191  I:  www.logitek.es 
Spain 
SWEDEN 
P&L Nordic AB  T:  +46 451 74 44 00 
Box 252  F:  +46 451 89 833 
S-281 23 Hässleholm  E: 
  h
ans.maunsbach@pol.se 
Sweden  I:  www.pol.se/profibus 
SWITZERLAND 
Berner Fachhochschule  T:  +41 (0) 34 426 68 32 
PROFIBUS Kompetenzzentrum  F:  +41 (0) 34 426 68 13 
Jlcoweg 1  E: 
 
max.felser@bfh.ch 
CH-3400 Burgdorf  I:  www.profitrace.ch 
Switzerland   
TAIWAN 
Full Data Technology  T:  +886-2-87519941/9097 
6F., No.200, Gangqian Rd.  F:  +886-2-87519533 
Neihu District, Taipei City  E: 
  s
ales@fulldata.com.tw 
114, Taiwan  I:  www.fulldata.com.tw 
TURKEY 
Emikon Otomasyon  T:  +90 216 420 8347 
DES Sanayi sitesi 103 sokak  F:  +90 216 420 8348 
B-7 blok No:16 Yukari Dudullu / Umraniye  E: 
  t
olgaturunz@emikonotomasyon.com 
Istanbul 34776  I:  www.emikonotomasyon.com 
Turkey   
UNITED ARAB EMIRATES 
Synergy Controls  T:  +971 4 3262692 
907, IT Plaza Silicon Oasis :  F:  +971 4 3262693 
DubaiI  E: 
  s
ales@synergycontrols.ae 
United Arab Emirates 
 
 
 
 
UNITED KINGDOM and N. Ireland 
Verwer Training & Consultancy  T:  +44 (0)1625 871199 
5 Barclay Road  E: 
  a
ndy@verwertraining.com 
Poynton, Stockport   I:  www.verwertraining.com 
Cheshire SK12 1YY   
United Kingdom 
 
Hi-Port Software  T:  +44 (0)8452 90 20 30  

ProfiHub A5/B5 User Manual

_______________________________________________

Version 2.1.1 – June 2014 Page 18 / 59

The Hub 2 Martin Close F: +44 (0)2392 552880

Lee-on-Solent E:

ales@hiport.co.uk

Hampshire PO13 8LG I: www.hiport.co.uk

United Kingdom

iTech T: +44 (0)1292 311 613

Unit 1 F: +44 (0)1292 311 578

Dukes Road E:

ales@itech-troon.co.uk

Troon I: www.itech-troon.co.uk

Ayrshire KA10 6QR

United Kingdom

Parkelect Ltd. T: +44 2890 777743

84 Dargan Road F: +44 2890 777794

Belfast E:

illan@parkelect.co.uk

BT3 9JU I: www.parkelect.co.uk

N. Ireland

UNITED STATES

Grid Connect Inc. T: +1 630 245-1445

1630 W. Diehl Road F: +1 630 245-1717

Naperville, Illinois 60563 E:

ales@gridconnect.com

USA I: www.gridconnect.com/procentec.html

VIETNAM

Bavitech Corporation T: +84-8-3547 0976

42 Truong Son Street F: +84-8-3547 0977

Ward 2, Tan Binh District E: hai.hoang@bavitech.com

Ho Chi Minh City I: www.bavitech.com

Vietnam

For the up to date list of the Sales Offices and

Distributors see

www.procentec.com/company/distributors/.

Order codes)

Termination LEDs

Yes

Ground rail

Optional (see chapter 0

3 Sales offices and

Distributors

HEADQUARTERS

PROCENTEC T: +31-(0)174-671800

Klopperman 16 F: +31-(0)174-671801

2292 JD WATERINGEN E:

fo@procentec.com

Yes

 
 
ProfiHub A5/B5 User Manual 
 
 
 
 _______________________________________________ 
          Version 2.1.1 – June 2014  Page 19 / 59 
ProfiHub-A5B5-Manual-EN  © PROCENTEC 2005-2014 - Copyright - all rights reserved 
Netherlands  I:   www.procentec.com 
ARGENTINA 
eFALCOM  T:  +54 237 46 31 151 
Alcorta 2411   F:  +54 237 46 31 150 
B1744 - Moreno  E: 
  s
antiago.falc[email protected] 
Buenos Aires  I:  www.efalcom.com.ar 
Argentina 
AUSTRALIA 
IS Systems Pty Limited  T:  +61 2 4964 8548 
14 Laverick Ave.,  F:  +61 2 4964 8877 
Tomago  E: 
  fr
itz.woller@issystems.com.au 
NSW, Australia, 2322  I:  www.issystems.com.au 
 
Pentair Flow Control Pacific  T:  +61 2 4448 0466 
1 Percival Road   F:  +61 2 4423 3232 
Smithfield  E: 
  s
haree.haze[email protected] 
NSW, Australia, 2164  I:  www.profibuscentre.com.au 
BELGIUM and LUXEMBOURG 
Bintz Technics N.V.  T:  +32 2 720 49 16 
Brixtonlaan 23  F:  +32 2 720 37 50 
B-1930 Zaventem  E: 
  bl
oemen@bintz.be 
Belgium  I:  www.bintz.be 
BRAZIL 
Westcon Instrument. Indl Ltda  T:  +55 11 5561-7488 
Rual Alvaro Rodrigues, 257  F:  +55 11 5093-2592 
São Paulo – SP  E: 
  p
[email protected]m.br 
Brazil - CEP 04582-000  I:  www.wii.com.br 
CANADA 
Streamline Process Management Inc.  T:  +1 403 225 1986 
#3, 4351 – 104 Ave SE  F:  +1 587 585 2828 
Calgary, Alberta T2C 5C6  E: 
  a
dmin@streamlinepm.com 
Canada  I:  www.streamlinepm.com 
CHILE 
RP Ingenieria Limitada  T:  +56-(0)41-2469350 
Tucapel 92 oficina 52  F:  +56-(0)41-2522592 
Concepción  E: 
  r
odrigopint[email protected] 
Chile  I:  www.rpingenieria.cl 
CHINA 
PROCENTEC Beijing  T:  +86(10)84766911 or 84787311 
Room E-1115 WangJingYuan YouLeHui  F:  +86(10)84766722 
ChaoYang  E: 
  in
fo@procentec.net 
Beijing  I:  www.procentec.net 
China 

 
 
ProfiHub A5/B5 User Manual 
 
 
 
 _______________________________________________ 
          Version 2.1.1 – June 2014  Page 20 / 59 
ProfiHub-A5B5-Manual-EN  © PROCENTEC 2005-2014 - Copyright - all rights reserved 
CZECH REPUBLIC 
FOXON s.r.o.  T:  +420 484 845 555 
Polní 367  F:  +420 484 845 556 
460 01 Liberec 12  E: 
  f
[email protected]z 
Czech Republic  I:  www.foxon.cz 
 
DENMARK 
ProSaiCon  T:  +45 70 20 52 01  
Jernbanegade 23B  F:  +45 70 20 52 02 
DK 4000 Roskilde  E: 
  h
fj@prosaicon.dk 
Denmark  I:  www.prosaicon.dk 
EGYPT 
Mas Trading  T:  +2 02 2524 2842 
37, 105 Street  F:  +2 02 2524 2843 
Al-Etihad Square  E: 
  a
ya.elshafe[email protected] 
Egypt  I:  www.masautomation.com 
ESTONIA 
Saksa Automaatika OU  T:  +372 605 2526 
Peterburi Tee 49  F:  +372 605 2524 
Tailinn  E: 
  in
fo@saksa-automaatika.ee 
EE-11415 Estonia  I:  www.saksa-automaatika.ee 
FINLAND 
Hantekno Oy  T:  +358 40 8222 014 
Kalliotie 2  E: 
  in
fo@hantekno.com 
04360 Tuusula  I:  www.hantekno.fi 
Finland   
FRANCE 
AGILiCOM  T:  +33 247 76 10 20 
Bâtiment B  F:  +33 247 37 95 54 
1, rue de la Briaudière  E: 
  jy
.bois@agilicom.fr 
Z.A. La Châtaigneraie  I:  www.agilicom.fr 
37510 BALLAN-MIRE   
France   
GERMANY 
PROCENTEC GmbH  T:  +49-(0)721 831 663-0 
Benzstrasse 15  F:  +49-(0)721 831 663-29 
D-76185 Karlsruhe  E: 
  in
fo@procentec.de 
Germany  I:  www.procentec.de  
INDIA 
UL Engineering Services & Software Pvt Ltd  T:  +91-202 696 0050 
Nirman Classic,  F:  +91-202 696 2079 
Katraj-Kondhwa Road,  E: 
  di
leep.miski[email protected]m 