1 POA201-10-2
AC-DC Power Adapter (12VDC, 1A)
POA201-10-2 User’s Guide
CONTEC CO., LTD.
This product is the AC adapter for input: 90 - 264VAC and output: +12VDC 1A.
Dimensions
Connector
MC1,5/3-ST-3,5 [made by Phoenix Contact Corp.]
POA201-10-2 User’s Guide
Copyright 2011-2024 CONTEC CO., LTD. ALL RIGHTS RESERVED.
CONTEC CO., LTD. January 2024 Edition
3-9-31, Himesato, Nishiyodogawa-ku, Osaka 555-0025, Japan
https://www.contec.com/ NA01072 (LYMB273)
01182024_rev3 [05202011]
No part of this document may be copied or reproduced in any form by any means without prior written
consent of CONTEC CO., LTD.
Specifications
Item
Specification
Input voltage range
90 - 264VAC
Rated input current
Rated input current depends on the model. Please refer to the label of the adapter.
300mA (3A-124DA12)
500mA (6A-151DA12A)
Number of frequency
50 - 60Hz
Rated output voltage
12.0VDC
Rated output current
1.0A (Max.)
Dimension (mm)
47.5(W) x 75(D) x 27.3(H) (No protrusions)
Weight
175g
Operating temperature
0 - 40
℃
Operating humidity
20 - 80%RH(No condensation)
Life expectancy
1.5 years at the ambient temperature 40
℃
(When 100VAC is input and 1.0A is output)
4 years at the ambient temperature 40
℃
(When 100VAC is input and 0.5A is output) *1
Allowable time of short
interruption
20ms (Max.) (When 100VAC is input and 0.55A is output) *2
Floating dust particles
Not to be excessive
Corrosive gases
None
Voltage corresponding to the
attached AC cable
125VAC 7A
*1 The current consumption(Max.) of the F&eIT N series supported by this product is 6.5W.
*2 When the short interruption occurs and the defective operation of the equipment is generated, please insert the
power supply of the equipment after pulling out it.
- Do not strike or bend this product. Otherwise, this may malfunction, overheat, cause a failure or
breakage.
- When plugging or unplugging the power cable, be sure to hold it by the plug itself.
- Do not insert or remove the connector while the power is turned on to the PC. Failure to observe this
precaution may cause malfunction, overheating.
- Insert or remove the cable straightly. Otherwise, the part of connector may distort, cause a failure or
breakage.
- No part of this document may be copied or reproduced in any form by any means without prior
written consent of CONTEC CO., LTD.
- All relevant issues have been considered in the preparation of this document. Should you notice an
omission or any questionable item in this document, please feel free to notify CONTEC CO., LTD.
- The specifications of this product are subject to change without notice for enhancement and quality
improvement. Even when using this product continuously, be sure to read the manual and understand
the contents.
- Do not modify this product. CONTEC will bear no responsibility for any problems, etc., resulting
from modifying this product.
- Regardless of the foregoing statement, CONTEC assumes no responsibility for any errors that may
appear in this document or for any results of using the product.
CAUTION
-
1
-
2
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Contec POA201-10-2 Owner's manual
-
-
-
-
-
-
-
-
-