NORD Drivesystems SK 300P - NORDAC ON/ON+ - frequency inverter User manual

BU 0800 – en

NORDAC ON (SK 300P series)

Manual with installation instructions

NORDAC ON (SK 300P series) – Manual with installation instructions

2 BU 0800 en-3623

Read document and keep for future reference

Read this document carefully prior to performing any work on or putting the device into operation. It is

essential to read and observe the instructions in this document. They serve as the prerequisite for

smooth and safe operation and the fulfilment of any warranty claims.

Contact Getriebebau NORD GmbH & Co. KG if your questions regarding the handling of the device are

not answered in this document or if you require further information.

The German version of this document is the original. The German document is always decisive. If this

document is available in other languages, this will be a translation of the original document.

Keep this document in the vicinity of the device so that it is available if required.

Please also note the following documents:

•Catalogue “NORDAC electronic drive technology” (E3000),

•Documentation for optional accessories

•Documentation for equipment which is attached or provided.

Please contact Getriebebau NORD GmbH & Co. KG if you require further information.

Documentation

Title:

BU 0800

Order no.:

6078002

Series:

SK 3xxP

Device series:

SK 300P, SK 301P, SK 310P, SK 311P, SK350P

Device types:

SK 3xxP-360-340-A … SK 31xP-371-340-A

0.37 kW … 3.70 kW, 3~ 400 V

Version list

BU 0800 en-3623 3

Version list

Title,

Date

Order number Software

version of

device

Remarks

BU 0800,

November 2021

6078002/ 4521

V 1.2 R5

• First issue

BU 0800,

February 2022

6078002/ 0822

V 1.2 R5

• “Maintenance information” chapter revised

BU 0800,

November 2022

6078002/ 4622

V 1.2 R6

• General corrections

• Supplementation of size 3

• Revision of the scaling tables

• Supplementation of disposal notes

BU 0800,

May 2023

6078002/ 2223

V 1.2 R9

• General corrections

• Supplement of type NORDAC ON PURE

• Supplement of SK 30x-191-340

• Supplement of SK 31x-371-340

• Revision of the scaling tables

• Revision of standards and approvals

• Revision of UL and CSA conditions

BU 0800,

September

2023

6078002/ 3623

V 1.2 R9

• Adjustment of information on maximum

operating / ambient temperature

• Revision of UL and CSA conditions

Copyright notice

As an integral component of the device described here, this document must be provided to all

users in a suitable form.

Any editing or amendment or other utilisation of the document is prohibited.

Publisher

Getriebebau NORD GmbH & Co. KG

Getriebebau-Nord-Straße 1 • 22941 Bargteheide, Germany • http://www.nord.com

Fon +49 (0) 45 32 / 289-0 • Fax +49 (0) 45 32 / 289-2253

Member of the NORD DRIVESYSTEMS Group

NORDAC ON (SK 300P series) – Manual with installation instructions

4 BU 0800 en-3623

Table of Contents

BU 0800 en-3623 5

Table of Contents

1 General ......................................................................................................................................................... 9

1.1 Overview .......................................................................................................................................... 10

1.2 Delivery ............................................................................................................................................ 12

1.3 Scope of delivery.............................................................................................................................. 12

1.4 Presentation conventions ................................................................................................................. 13

1.4.1 Warning information ........................................................................................................... 13

1.4.2 Other information ................................................................................................................ 13

1.4.3 Text markings ..................................................................................................................... 13

1.5 Safety, installation and application information ................................................................................ 14

1.6 Warning and hazard information ...................................................................................................... 18

1.6.1 Warning and hazard information on the product ................................................................. 18

1.6.2 Warning information on the upper shell .............................................................................. 18

1.7 Standards and approvals ................................................................................................................. 19

1.7.1 UL and CSA approval ......................................................................................................... 19

1.8 Type code / nomenclature ................................................................................................................ 21

1.8.1 Name plate ......................................................................................................................... 21

2 Assembly and installation ........................................................................................................................ 22

2.1 Installation ........................................................................................................................................ 22

2.2 Dimensions NORDAC ON, motor-mounted ..................................................................................... 23

2.3 Dimensions NORDAC ON+, motor-mounted ................................................................................... 24

2.4 Dimensions NORDAC ON PURE, motor-mounted .......................................................................... 25

2.5 Dimensions NORDAC ON and NORDAC ON+, wall-mounted ........................................................ 26

2.6 Dimensions NORDAC ON PURE, wall-mounted ............................................................................. 27

2.7 Connections ..................................................................................................................................... 28

2.7.1 NORDAC ON, motor-mounted, size 1 ................................................................................ 28

2.7.2 NORDAC ON, motor-mounted, sizes 2 and 3 .................................................................... 29

2.7.3 NORDAC ON+, motor-mounted, sizes 2 and 3 .................................................................. 30

2.7.4 NORDAC ON PURE, motor-mounted, sizes 2 and 3 ......................................................... 31

2.7.5 NORDAC ON, wall-mounted, size 1 ................................................................................... 32

2.7.6 NORDAC ON and NORDAC ON+, wall-mounted, sizes 2 and 3 ....................................... 33

2.7.7 NORDAC ON PURE, wall-mounted, sizes 2 and 3 ............................................................ 34

2.7.8 Hybrid cable........................................................................................................................ 34

2.8 Electrical Connection ....................................................................................................................... 35

2.8.1 NORDAC ON and NORDAC ON+ mains connection ......................................................... 35

2.8.2 NORDAC ON PURE mains connection .............................................................................. 36

2.8.3 Daisy chain connection ....................................................................................................... 37

2.8.4 Motor connection ................................................................................................................ 38

2.8.5 Wiring guidelines ................................................................................................................ 39

2.8.6 Electrical connection of power unit ..................................................................................... 39

2.8.6.1 Mains connection 40

2.8.6.2 Motor cable 40

2.8.6.3 Braking resistor (optionally with size 2 and above) 41

2.8.6.4 Electromechanical brake (optionally with size 2 and above) 41

2.8.7 Electrical connection Ethernet communication and digital input/outputs ............................ 42

2.8.7.1 Control connection details 44

2.9 Diagnostic connection ...................................................................................................................... 45

2.10 Encoder ............................................................................................................................................ 46

3 Display ....................................................................................................................................................... 49

3.1 LEDs ................................................................................................................................................ 49

3.1.1 Display of M1 and M2 when using EtherCAT ..................................................................... 49

3.1.2 Display of M1 and M2 when using EthernetIP .................................................................... 50

3.1.3 Display of M1 and M2 when using PROFINET ................................................................... 51

3.1.4 Display M3 .......................................................................................................................... 51

3.1.5 Display of M4 and M5 ......................................................................................................... 52

3.2 Diagnostic LED ................................................................................................................................ 52

4 Commissioning ......................................................................................................................................... 53

4.1 Starting up the device ...................................................................................................................... 53

NORDAC ON (SK 300P series) – Manual with installation instructions

6 BU 0800 en-3623

4.2 Firmware update .............................................................................................................................. 54

4.3 Selecting the operating mode for motor control ............................................................................... 54

4.3.1 Explanation of the operating modes (P300) ....................................................................... 54

4.3.2 Overview of controller parameter settings .......................................................................... 56

4.3.3 Motor control commissioning steps .................................................................................... 57

5 Parameter ................................................................................................................................................... 58

5.1 Parameter overview ......................................................................................................................... 60

5.1.1 Operating displays .............................................................................................................. 63

5.1.2 Basic parameters ................................................................................................................ 65

5.1.3 Motor data .......................................................................................................................... 71

5.1.4 Speed control ..................................................................................................................... 80

5.1.5 Control terminals ................................................................................................................ 88

5.1.6 Additional parameters ......................................................................................................... 99

5.1.7 Information........................................................................................................................ 113

6 Operating status messages ................................................................................................................... 122

6.1 Display of messages ...................................................................................................................... 122

6.2 Messages ....................................................................................................................................... 122

6.3 FAQ operational problems ............................................................................................................. 134

7 Technical data ......................................................................................................................................... 136

7.1 General frequency inverter data ..................................................................................................... 136

7.2 Maximum operating / ambient temperature .................................................................................... 137

7.2.1 Wall-mounted frequency inverters .................................................................................... 138

7.2.2 Motor-mounted frequency inverters .................................................................................. 139

7.2.3 Reducing the maximum ambient temperature .................................................................. 140

7.2.3.1 When using daisy chain 140

7.2.3.2 With reduced 24 V DC supply voltage 140

7.3 Technical data for determining the energy efficiency level ............................................................. 141

7.3.1 Electrical data 3~400 V ..................................................................................................... 142

7.3.1.1 NORDAC ON, size 1 142

7.3.1.2 NORDAC ON, NORDAC ON+, NORDAC ON PURE, size 2 143

7.3.1.3 NORDAC ON, NORDAC ON+, NORDAC ON PURE, size 3 143

7.4 Electrical data for 24 V DC supply ................................................................................................. 143

7.5 Electrical data for daisy chain operation ......................................................................................... 144

7.5.1 Electrical data for braking resistor (optional) .................................................................... 144

8 Additional information ............................................................................................................................ 145

8.1 Electromagnetic compatibility (EMC) ............................................................................................. 145

8.1.1 General Provisions ........................................................................................................... 145

8.1.2 EMC evaluation ................................................................................................................ 146

8.1.3 EMC of device .................................................................................................................. 147

8.1.4 Declarations of Conformity ............................................................................................... 149

8.2 Reduced output power ................................................................................................................... 151

8.2.1 Derating depending on the pulse frequency ..................................................................... 151

8.2.2 Reduced overcurrent due to the time ............................................................................... 152

8.2.3 Reduced overcurrent due to output frequency.................................................................. 153

8.2.4 Reduced output current due to low voltage ...................................................................... 154

8.2.5 Reduced output current due to the heat sink temperature ................................................ 154

8.3 Operation on the RCD .................................................................................................................... 154

8.4 Motor data – characteristic curves (asynchronous motors) ............................................................ 154

8.5 Motor data – characteristic curves (synchronous motors) .............................................................. 155

8.6 Scaling of setpoint/actual values .................................................................................................... 155

8.6.1 Setpoints .......................................................................................................................... 155

8.6.2 Actual values .................................................................................................................... 157

8.7 Definition of set and actual value processing (frequencies) ........................................................... 158

8.8 Connection accessories ................................................................................................................. 159

8.8.1 Motor cable ....................................................................................................................... 159

8.8.2 Hybrid motor cable ........................................................................................................... 159

8.8.3 Mains cable ...................................................................................................................... 159

8.8.4 Hybrid mains cable ........................................................................................................... 160

8.8.5 Daisy chain cable ............................................................................................................. 160

8.8.6 Daisy chain hybrid cable ................................................................................................... 160

8.8.7 Sealing caps ..................................................................................................................... 160

8.8.8 Encoder cables ................................................................................................................. 160

Table of Contents

BU 0800 en-3623 7

9 Maintenance and servicing information ................................................................................................ 161

9.1 Maintenance information ................................................................................................................ 161

9.2 Service notes ................................................................................................................................. 162

9.3 Disposal ......................................................................................................................................... 163

9.3.1 Disposal according to German law ................................................................................... 163

9.3.2 Disposal outside of Germany............................................................................................ 163

9.4 Abbreviations ................................................................................................................................. 164

NORDAC ON (SK 300P series) – Manual with installation instructions

8 BU 0800 en-3623

1 General

BU 0800 en-3623 9

1 General

The devices have sensorless current vector control with a wide range of settings. In combination with

suitable motor models, which always provide an optimised voltage/frequency ratio, all three-phase

asynchronous motors that are suitable for inverter operation and permanently excited synchronous

motors (IE4, IE5+) can be driven. For the drive unit, this means very high starting and overload torques

with constant speed.

The power range is from 0,37 kW to 3,7 kW.

The device series can be adapted to individual requirements by means of modular assemblies.

This manual is based on the device software as stated in the version list (see P707). If the frequency

inverter uses a different software version, this may cause differences. If necessary, the current manual

can be downloaded from the Internet (http://www.nord.com/).

Additional descriptions exist for optional functions and bus systems (http://www.nord.com/).

Information

Accessories

The accessories that are mentioned in the manual are also subject to changes. Current details of these

are included in separate data sheets, which are listed under www.nord.com under th

e heading

Documentation → Manuals → Electronic drive technology → Techn. info / Data sheet. The data sheets

available at the date of publication of this manual are listed by name in the relevant sections (TI ...).

The device is either mounted directly on a motor or in the vicinity of the motor (on the wall or on a

machine frame).

All electrical connections (power connections and control connections) are made with plug connectors.

This simplifies the installation of the device.

Parameters can be accessed as follows:

• Via Ethernet connection

The three Ethernet dialects PROFINET IO, EtherNet/IP and EtherCAT are available for this.

• Via the diagnostic port D1

The diagnostic port is designed as an RJ12 port and offers the possibility of using the following via

an internal RS232/RS485 interface

– an optional SimpleBox or ParameterBox, or

– the NORDAC ACCESS BT (SK TIE5 BT stick), or

– a PC with the installed NORDCON software.

The parameter settings modified by the operator are backed up in the integrated, non-volatile memory

of the device.

The device is configured according to the customer’s individual requirements. The device equipment is

therefore realised ex works. Later retrofitting of options or device conversions are not planned.

NORDAC ON (SK 300P series) – Manual with installation instructions

10 BU 0800 en-3623

Information

The device does not need to be opened at any time during its service life. All mounting, installation and

commissioning works are only done on the closed device.

•Assembly is done via freely accessible mounting holes.

•Electrical connection is exclusively established via plug connectors.

•Operational settings are made via parameter adjustments.

•Blind plugs may only be removed for works in connection with commissioning and must be properly

replaced afterwards.

•Diagnostic LEDs for displaying switching and operating states are externally visible.

•The cover cap of the diagnostic port D1 only requires removal for the connection of parameterisation

tools such as a PC, ParameterBox or NORDAC ACCESS BT. After successful parameterisation,

the cover cap must be replaced.

1.1 Overview

Model NORDAC ON

SK 30xP

NORDAC ON

SK 30xP

NORDAC ON+

SK 31xP

NORDAC ON

PURE

SK 350P

Power 0.37–0.45 kW 0.37–3.0 kW 0.37–3.7 kW 0.37–1.5 kW

Size 1 2 - 3 2 - 3 2 - 3

Sensorless current vector control

(ISD control)



RS485/RS232 diagnostic interface

via RJ12



Four separate online switchable

parameter sets



LEDs for diagnosis



LEDs for the DIs/DOs signal statuses



–

Integrated PLC,



BU 0550



Integrated Industrial Ethernet

interface EtherCAT®, EtherNet/IP®,

PROFINET IO®,  BU 0820



Stator resistance measurement



Load monitor



Functional safety connection facility

–

O

–

Internal braking resistor

–

O

External 24 V supply of the control

board



Operation of three-phase

as

ynchronous

m

otors (ASM)



Operation of IE5+ motors

–



Mountable on IE3 motor



–

Mountable on IE5+ motor

–



Brake management for mechanical

holding brake –



POSICON

RS 485 encoder interface for speed

control (closed-loop, servo mode)

and positioning tasks

– –



1 General

BU 0800 en-3623 11

Model NORDAC ON

SK 30xP

NORDAC ON

SK 30xP

NORDAC ON+

SK 31xP

NORDAC ON

PURE

SK 350P

Power 0.37–0.45 kW 0.37–3.0 kW 0.37–3.7 kW 0.37–1.5 kW

Size 1 2 - 3 2 - 3 2 - 3

Integrated EMC mains filter    

Hybrid circular connectors for mains

input / control voltage / Ethernet / and

data

– – – 

Hybrid circular connectors for mains

output / daisy chain / control voltage /

Ethernet / and data

– – – 

Mains input (3-phase 400 V) with

integrated 24 V DC via plug    –

Mains output / daisy chain (3-phase

400 V) with integrated 24 V DC via

plug

   –

Thermostats (PTC)    

DIN via M12 plug connector    –

DOUT via M12 plug connector    –

– Not available

Optional properties

Depending on the device configuration, the meanings of the individual LEDs, the functions or

assignments of individual plugs or the function of control elements (e.g. switches) may differ. The

possible combinations are shown and explained in the course of this manual. The individual equipment

of the device is shown on the name plate and can be compared with the information in the manual.

Available as standard

O Optional

NORDAC ON (SK 300P series) – Manual with installation instructions

12 BU 0800 en-3623

1.2 Delivery

Examine the device for transport damage or loose components immediately on delivery / unpacking.

In case of damage, contact the carrier immediately and arrange for a careful survey.

Important! This also applies if the packaging is undamaged.

1.3 Scope of delivery

NOTICE

Defect in the device

Use of impermissible accessories and options (e.g. also options for other inverter series) may result in

defects of interconnected components.

•Only use accessories and options which are explicitly intended for use with this device and stated

in this manual.

Standard version: •Device according to customer order, protection class see 7.1 "General

frequency inverter data"

•Operating instructions as PDF file on CD ROM including NORDCON, (PC

parametrisation software)

•Warning signs as addition for assembly near to the device according to

UL/cUL, 1x each in the languages English and French:

•Warning sign as addition for assembly near to the device according to UL,

1x in English language:

1 General

BU 0800 en-3623 13

1.4 Presentation conventions

1.4.1 Warning information

Warning information for the safety of users are marked as follows:

DANGER

This warning information warns of danger to persons that results in severe injuries or death.

WARNING

This warning information warns of danger to persons that could result in severe injuries or death.

CAUTION

This warning information warns of danger to persons that could usually result in moderate injuries.

NOTICE

This warning information warns of material damage.

1.4.2 Other information

Information

This information shows tips and important information.

1.4.3 Text markings

The following markings are used to differentiate between various types of information:

Text

Type of information Example Marking

Instructions

1.

2.

Instructions whose sequence must be complied with

are numbered sequentially.

Bullet points • Bullet points are marked with a dot.

Parameter

P162

Parameters are indicated by a “P” prefix, a three-

digit number and bold lettering.

Arrays

[-01]

Arrays are indicated by square brackets.

Factory settings

{ 0.0 }

Factory settings are indicated by curly brackets.

Software descriptions

“Cancel”

Menus, fields, windows, buttons and tabs are

indicated by quotation marks and bold lettering.

NORDAC ON (SK 300P series) – Manual with installation instructions

14 BU 0800 en-3623

Numbers

Type of information Example Marking

Binary numbers

100001b

Binary numbers are indicated by the suffix “b”.

Hexadecimal numbers

0000h

Hexadecimal numbers are indicated by the suffix “h”.

1.5 Safety, installation and application information

Before working on or with the device, please read the following safety instructions extremely carefully.

Please pay attention to all other information from the device manual.

Non-compliance can result in serious or fatal injuries and damage to the device or its surroundings.

These safety instructions must be kept in a safe place!

1. General

Do not use defective devices or devices with defective or damaged housings or missing covers (e.g.

blind plugs for cable glands). Otherwise, there is a risk of serious injury or death from electric shock or

rupture of electrical components, e.g. high power capacitors.

Unauthorised removal of covers, improper use, incorrect installation or operation causes a risk of serious

personal injury or material damage.

Depending on its protection class, the devices may have live, bare, moving or rotating parts or hot

surfaces during operation.

The device is operated with hazardous voltage. Dangerous voltage may be present at the supply lines,

contact strips and PCBs of all connecting terminals (e.g. mains input, motor connection), even if the

device is not working or the motor is not rotating (e.g. caused by electronic disabling, jamming of the

drive or a short circuit at the output terminals).

The device is not equipped with a master mains switch and is thus always live when connected to mains

voltage. Voltages may therefore be connected to a connected motor at standstill.

A connected motor may also rotate if the drive is disconnected from the mains and possibly generate

hazardous voltage.

If persons come into contact with dangerous voltage such as this, there is a risk of an electric shock,

which can lead to serious or fatal injuries.

The device and any power plug connectors must not be disconnected while a voltage is applied to the

device. Failure to comply with this may cause arcing, which in addition to the risk of injury, also may

result in a risk of damage or destruction of the device.

The fact that the status LED or other indicators are not illuminated does not safely indicate that the

device has been disconnected from the mains and is without voltage.

The heat sink and all other metal components may heat up to temperatures above 70 °C.

Touching these parts can result in local burns to the body parts concerned (cooling times and clearance

from neighbouring components must be complied with).

All work on the device, e.g. transportation, installation, commissioning and maintenance work must be

carried out by qualified personnel (observe IEC 364 or CENELEC HD 384 or DIN VDE 0100 and

IEC 664 or DIN VDE 0110 and national accident prevention regulations). In particular, the general and

regional installation and safety regulations for work on low-voltage systems (e.g. VDE) must be complied

with, as must the regulations concerning correct use of tools and the use of personal protection

equipment.

During all work on the device, take care that no foreign bodies, loose parts, moisture or dust enter or

remain in the device (risk of short circuit, fire and corrosion).

1 General

BU 0800 en-3623 15

With certain setting conditions, the device or the motor which is connected to it may start automatically

when the mains are switched on. The machinery which it drives (press / chain hoist / roller / fan etc.)

may then make an unexpected movement. This may cause various injuries, including to third parties.

Before switching on the mains, secure the danger area by warning and removing all persons from the

danger area.

Further information can be found in this documentation.

Triggering of a circuit breaker

If the device is secured by a circuit breaker and if this was triggered, this may indicate that a residual

current was interrupted. A component (e.g. device, cable or plug connector) in this circuit may have

caused an overload (e.g. short circuit or earth fault).

A direct reset of the circuit breaker may lead to the circuit breaker not being triggered afterwards

although the fault cause is still present. As a result, any current flowing into the fault location may cause

overheating and ignite the surrounding material.

After each triggering of a circuit breaker, all live components within this circuit must thus be visually

checked for defects and flashover tracks. Also check the connections at the device’s connection

terminals.

In case of no faults found or after the replacement of the defect components, switch on the power supply

by resetting the circuit breaker. Carefully observe the components keeping a safe physical distance. As

soon as you observe a malfunction (e.g. smoke, heat or unusual odours), the occurrence of a new fault

or if the status LED on the device does not light up, switch off the circuit breaker immediately and

disconnect the defect component from the mains. Replace the defect component.

2. Qualified specialist personnel

Within the meaning of this basic safety information, qualified specialist personnel are persons who are

familiar with the installation, assembly, commissioning and operation of the product and who have the

qualifications appropriate to their work.

In addition, the device and the accessories associated with it must only be installed and commissioned

by a qualified electrician. A qualified electrician is a person who, because of his/her technical training

and experience, has sufficient knowledge with regard to

• switching on, switching off, disconnection, earthing and labelling of electric circuits and devices,

• correct maintenance and use of protective devices according to specified safety standards.

3. Do not make any modifications.

Unauthorised changes and the use of spare parts and additional equipment tnot purchased from or

recommended by NORD may cause fire, electric shock and injury.

Do not change the original coating / paint or apply additional coatings / paints.

Do not make any structural modifications to the product.

4. Intended use – general

Frequency inverters are devices for industrial and commercial systems that are used to operate three-

phase asynchronous motors with squirrel-cage rotors and Permanent Magnet Synchronous Motors –

PMSM (IE4, IE5+). These motors must be suitable for operation with frequency inverters, other loads

must not be connected to the devices.

The devices are components intended for installation in electrical systems or machines.

Technical data and information for connection conditions can be found on the rating plate and in the

documentation, and must be complied with.

The devices may only be used for safety functions which are described and explicitly approved.

CE-labelled devices meet the requirements of the Low Voltage Directive 2014/35/EU. The stated

harmonized standards for the devices are used in the declaration of conformity.

NORDAC ON (SK 300P series) – Manual with installation instructions

16 BU 0800 en-3623

a. Supplement: Intended use within the European Union

When installed in machines, commissioning of the devices (i.e. commencement of proper use) is

prohibited until it has been ensured that the machine fulfils the provisions of EC Directive

2006/42/EC (Machinery Directive); EN 60204-1 must also be complied with.

Commissioning (i.e. start of intended use) is only permitted if the EMC directive (2014/30/EU) is

complied with.

b. Supplement: Intended use outside the European Union

The local conditions of the operator for the installation and commissioning of the device must be

complied with at the usage location (see also “a. Supplement: Intended use within the European

Union”).

5. Phases of life

Transport, storage

The information in the manual regarding transport, storage and correct handling must be complied with.

The permissible mechanical and climatic ambient conditions (see technical data in the manual for the

device) must be complied with.

If necessary, suitable, adequately dimensioned means of transport (e.g. lifting gear, rope guides) must

be used.

Installation and assembly

The installation and cooling of the device must be implemented according to the regulations in the

corresponding documentation. The permissible mechanical and climatic ambient conditions (see

technical data in the manual for the device) must be complied with.

The device must be protected against impermissible loads. In particular, components must not be

deformed and/or insulation distances must not be changed. Touching of electronic components and

contacts must be avoided.

The device and its optional modules contain electrostatically sensitive components, which can be easily

damaged by incorrect handling. Electrical components must not be mechanically damaged or destroyed.

Electrical connection

Ensure that the device and the motor are specified for the correct supply voltage.

Installation, maintenance and repair work must not be carried out unless the device has been

disconnected from the voltage and at least 5 minutes have elapsed since the mains was switched off!

(Due to charged capacitors, hazardous voltages may be present on the device for up to 5 minutes after

being switched off from the mains). Before starting work it is essential to check by measurement that all

contacts of the power plug connections or the connection terminals are voltage-free.

The electrical installation must be implemented according to the applicable regulations (e.g. cable cross-

section, fuses, earth lead connections). Further instructions can be found in the documentation or

manual for the device.

Information regarding EMC-compliant installations such as shielding, earthing, location of filters and

routing of cables can be found in the documentation for the devices and in the technical information

manual TI 80-0011. This information must always be observed even with devices with a CE label.

Compliance with the limit values specified in the EMC regulations is the responsibility of the

manufacturer of the system or machine.

In case of a fault, inadequate earthing may result in electric shock, possibly with fatal consequences.

The device may only be operated with effective earth connections which comply with local regulations

for large leakage currents (> 3.5 mA). Detailed information regarding connections and operating

conditions can be obtained from the technical Information manual TI 80-0019.

1 General

BU 0800 en-3623 17

Connection of the supply voltage may directly or indirectly set the device into operation. Contact with

electrically live components may result in electric shock, possibly with fatal consequences.

All poles of cable connections (e.g. power supply) must always be disconnected.

Setup, troubleshooting and commissioning

When working on live devices, the applicable national accident prevention regulations must be complied

with.

Connection of the supply voltage may directly or indirectly set the device into operation. Contact with

electrically live components may result in electric shock, possibly with fatal consequences.

The parametrisation and configuration of the devices must be selected so that no hazards can occur.

Operation

Where necessary, systems in which the devices are installed must be equipped with additional

monitoring and protective equipment according to the applicable safety requirements (e.g. legislation

concerning technical equipment, accident prevention regulations, etc.).

All covers must be kept closed during operation.

Due to its operation, the device produces noises within the audible frequency range. These noises may

cause long-term stress, discomfort and fatigue, with negative effects on concentration. The frequency

range or the noise can be shifted to a less disturbing or almost inaudible range by adjustment of the

pulse frequency. However, this may possibly result in derating (lower power) of the device.

Maintenance, repair and decommissioning

Installation, maintenance and repair work must not be carried out unless the device has been

disconnected from the voltage and at least 5 minutes have elapsed since the mains was switched off!

(Due to charged capacitors, hazardous voltages may be present on the device for up to 5 minutes after

being switched off from the mains). Before starting the work, it is essential to check by measurement

that all contacts of the power plug connectors or the connection terminals are voltage-free.

Disposal

The product and its parts and accessories must not be disposed of as domestic waste. At the end of its

life, the product must be properly disposed of according to the local regulations for industrial waste. In

particular, this product contains integrated semiconductor circuits (PCBs and various electronic

components, including high power electrolytic capacitors). In case of incorrect disposal there is a risk of

formation of toxic gases, which may cause contamination of the environment and direct or indirect

injuries (e.g. chemical burns). In the case of high power electrolytic capacitors, there is also a risk of

explosion, with the associated risk of injury.

6. Potentially explosive environment (ATEX)

The device is not approved for operation or maintenance work in potentially explosive environments

(ATEX).

NORDAC ON (SK 300P series) – Manual with installation instructions

18 BU 0800 en-3623

1.6 Warning and hazard information

Under certain circumstances, hazardous situations may occur in association with the frequency inverter.

In order to give explicit warning of possibly hazardous situations, clear warning and hazard information

can be found on the device and in the relevant documentation.

1.6.1 Warning and hazard information on the product

The following warning and hazard information is used on the product.

Symbol Supplement to

symbol 1) Meaning

DANGER

Device is live

>5min after

removing mains

voltage

Danger

Electric shock

The device contains powerful capacitors. Because of this, there may be a

hazardous voltage for more than 5 minutes after disconnection from the mains.

Before starting work, check that the device is free of voltage at all power

contacts by means of suitable measuring equipment.

It is essential to read the manual in order to prevent hazards!

CAUTION

Hot surfaces

The heat sink and all other metal components as well as the surfaces of plug

connectors may heat up to temperatures in excess of 70°C.

•Danger of injury due to local burns on contact.

•Heat damage to adjacent objects

Allow sufficient cooling time before starting work on the device. Check the

surface temperatures with suitable measuring equipment. Maintain an

adequate distance to adjacent components or provide protection against

contact.

NOTICE

EDS

The device contains electrostatically sensitive components, which can be

easily damaged by incorrect handling.

Avoid all contact (indirect contact by tools or similar, or direct contact) with

PCBs and their components.

1) Texts are written in English.

Table 1: Warning and hazard information on the product

1.6.2 Warning information on the upper shell

Important information regarding danger of electric shock and hot surfaces can be found at the side of

the upper shell of the device.

1 General

BU 0800 en-3623 19

1.7 Standards and approvals

All devices across the entire series comply with the standards and directives listed below.

Approval Directive Applied

standards Certificates Label

CE

(European

Union)

Low Voltage 2014/35/EU

EN 61800-5-1

EN 60529

EN 61800-3

EN 63000

EN 61800-9-1

EN 61800-9-2

C310001_0921

EMC 2014/30/EU

RoHS 2011/65/EU

Delegated directive

(EU) 2015/863

Ecodesign

2009/125/EC

Regulation (EU)

Ecodesign 2019/1781

UL

(USA) UL 61800-5-1 E171342

CSA

(Canada) C22.2 No.274-13 E171342

RCM

(Australia) F2018L00028 EN 61800-3 ------

UkrSEPRO

(Ukraine)

EN 61800-5-1

EN 60529

EN 61800-3

EN 63000

EN 60947-1

EN 60947-4

EN 61558-1

EN 50581

C311900

UKCA

(United

Kingdom)

EN 61800-5-1

EN 60529

EN 61800-3

EN 63000

EN 61800-9-1

EN 61800-9-2

C352000

Table 2: Standards and approvals

1.7.1 UL and CSA approval

File No. E171342

The categorisation of protective equipment approved by the UL according to United States standards

for the devices described in this manual is listed below, basically with the original wording. The

categorisation of the individually relevant fuses or circuit breakers can be found in the “Electrical Data”

section of this manual.

All devices include motor protection.

Additional adhesive labels with supplementary warning information

Attach the signs enclosed with the device and listed according to Section 1.3 "Scope of delivery"in a

clearly visible position in the immediate vicinity of the device.

NORDAC ON (SK 300P series) – Manual with installation instructions

20 BU 0800 en-3623

Conditions UL/CSA according to report

Information

•Listed as ENCLOSED POWER CONVERSION EQUIPMENT

•These devices incorporate an adjustable internal solid-state motor overload protection (see P533, P535)

• “Integral solid state short circuit protection does not provide branch circuit protection. Branch circuit

protection must be provided in accordance with the Manufacturer Instructions, National Electrical Code and

any additional local codes”.

CSA: For Canada: “Integral solid state short circuit protection does not provide branch circuit protection.

Branch circuit protection must be provided in accordance with the Canadian Electrical Code, Part I”.

•“Use min. 75°C rated Copper Conductors Only”.

•“For use in Pollution Degree 3 and Overvoltage Category III environments only.”

•“Maximum surrounding air Temperature 40°C (S1) - 50°C (S3-70%). ( see chapter 7 )

•“The device has to be mounted according to the Manufacturer Instructions.”.

•“For NFPA79 applications only”

•“Control circuit is Limited Voltage / Limited Current maximum 30 V/ 3 A

•“External protective means (e.g. thermal sensor or switch embedded in the motor or from an external

protective relay) may be additionally used”.

•“The source shall be derived from a non-corner grounded type TN AC source not exceeding 277 V phase to

earth”.

• “They are suitable for operation on TN as well as for IT networks with the configuration of the integrated

mains filter.”

Frame

Size

description

all

“Suitable for use on a circuit capable of delivering not more than 10 kA rms symmetrical amperes, 480

(3-phase) volts max., when protected by high-interrupting capacity, current limiting class RK5 fuses or

faster, rated min. 480 Volts”. 1)

This is not applicable for devices with QPD-W Connector.

all

“Suitable for use on a circuit capable of delivering not more than 10 kA rms symmetrical amperes, 480

Volt maximum, when protected by circuit breaker (inverse time trip type) in accordance with UL 489,

min. 480 Volts”. 1)

This is not applicable for devices with QPD-W Connector.

all

“Suitable for motor group installation on a circuit capable of delivering not more than 10 kA rms

symmetrical amperes, 480 (3-phase) V max, when protected by high-interrupting capacity, current

limiting class RK5 fuses or faster, rated max. 30 Amperes”.

If provided with QPD-W Connector the SCCR is max. 5 kA with class J fuses or faster.

all

“Suitable for motor group installation on a circuit capable of delivering not more than 10 kA rms

symmetrical amperes, 480 (3-phase) V max, when protected by circuit breaker (inverse time trip type)

in accordance with UL 489, rated max. 30 Amperes and 480 Volts min.”

This is not applicable for devices with QPD-W Connector.

1)

(



see chapter 7)

Page is loading ...

NORD Drivesystems SK 300P - NORDAC ON/ON+ - frequency inverter User manual

This manual is also suitable for

NORD Drivesystems SK 300P - NORDAC ON/ON+ - frequency inverter User manual

Related papers

Other documents