Channel Plus 7441 Install Manual

Brand: Channel Plus

Model: 7441

Type: Install Manual

74 41

CAMERA

MOUNTING

KIT

For Use with the

Model 7440 CCTV Camera

PRODUCT DESCRIPTION

The Model 7441 Camera Mounting Kit is designed for use with

the Model 7440 Color CCTV Camera. The kit enhances the

installation options for the camera. Available in white (Model

7441W) and black (Model 7441B), the kit features two mounting

options for discrete, attractive CCTV camera installation.

The camera can be installed recessed in a wall or surface

mounted depending on the application. Installations that

require stealthy, low-proﬁ le mounting should use the recessed

mounting option. The surface mounting option works well in

retroﬁ t installations and other mounting applications.

CAMERA MOUNTING KIT COMPONENTS INSTALL THE CAMERA IN THE BALL

SURFACE MOUNTING RECESSED MOUNTING VIDEO CONNECTION

POWER CONNECTION ALIGNMENT & TESTING SPECIFICATIONS

IMAGING ELEMENT: CCD

LENS: 2.1 mm, f 2.0

LUX: 0.5 minimum

RESOLUTION: 380 TV Lines

HORIZONTAL VIEWING ANGLE: 120°

VERTICAL VIEWING ANGLE: 100°

VIDEO OUTPUT: 1 volt peak-to-peak

VIDEO OUTPUT IMPEDANCE: 75Ω

POWER REQUIREMENTS: 12 VDC @ 90 mA

(Power supply included)

WIRING REQUIREMENTS: VIDEO: RG-59 or RG-6

(RG-6U recommended)

POWER: 18 AWG

2-conductor

LINEAR LIMITED WARRANTY

Linear LLC warrants this product to be free from defects in material and workmanship for 1

year. The time period will be measured using the date code labeled on the product. Linear

LLC is not responsible for damage to the product resulting from the buyer’s improper handling,

stocking or warehousing of the product. Any implied warranty arising from the sale of the

product including implied warranties of merchantability and fitness for purpose are limited.

Linear LLC shall not be responsible for any losses, damages or expenses, whether direct,

consequential, or incidental arising from the use or the inability to use the product. Some

states and countries do not allow limitations or how long an implied warranty lasts or the

exclusion or limitation or incidental or consequential damages, so the above exclusions may

not apply. The Linear LLC warranty gives specific legal rights in addition to other rights, which

may exist and vary from state to state and country to country.

The warranty is limited to repair or replacement of products returned, freight prepaid, to Linear

LLC, there is NO PROVISION FOR LABOR COST OR OTHER REIMBURSEMENTS OF

ANY KIND.

1. Failures due to product abuse, such as negligence, improper use, and electrical

surge including damage from lightning, water damage or other damage due to natural

disasters are not covered by the warranty. The most common form of product abuse is

surge damage caused by lightning.

2. The warranty shall also be voided by any tampering with the date code, labels or other

markings on the product.

3. Products that are damaged in transit to Linear LLC due to improper packaging or by the

carrier (shipping company) will not be covered under the warranty. If the product was

damaged or lost by the carrier, it is the sender’s responsibility to create a claim against

the carrier.

4. The user is responsible for all labor costs associated with removing, reinstalling and

returning the product to Linear LLC.

Linear LLC, at its option, will repair or replace the defective product. Replacements will be

made from B-Stock, if an exact replacement is not available, Linear LLC, at its option, will

select the nearest equivalent product. The user is responsible for freight charges to Linear LLC.

Linear LLC will return warranted repaired or replacements by UPS Ground or an equivalent

service. A customer may pay the additional costs for second-day or next-day service.

All products returned for warranty service require a Return Product Authorization Number

(RPA#). Contact Linear Technical Services at 1-800-999-5225 for an RPA# and other

important details.

Linear LLC

2055 Corte Del Nogal, Carlsbad, CA 92009, USA

760-438-7000

800-999-5225

fax: 760-931-1340

www.channelplus.com

RECESS

FLANGE

DOME

COVER

MAIN

BRACKET

TRIM

RING

CAMERA

BALL BASE

CAMERA

BALL TOP

1-1/2"

SCREWS

1/2"

SCREWS

1/4"

SCREWS

REMOVE

LENS CAP

ROUTE

WIRE

THROUGH

BALL BASE

CAMERA

BALL BASE

CAMERA

BALL TOP

SLIDE CAMERA

INTO BALL BASE

WIRE ON TOP

EDGE OF CAMERA

2 3PUT THE BALL TOP

ON THE BALL BASE

ALIGN SLOT WITH

TAB ON BALL TOP

INSTALL TWO 1/4"

SCREWS

ATTACH THE MAIN BRACKET

WITH THREE 1-1/2" SCREWS

FOR RECESSED WIRING

DRILL A 9/16" HOLE

FOR SURFACE WIRING

ROUTE WIRE IN SLOT

SLIDE DOME OVER

CAMERA BALL

SLOT ON DOME ALIGNS

WITH THE WIRE SLOT

INSTALL THREE 1/2" SCREWS

(WAIT UNTIL ALIGNMENT IS COMPLETE

BEFORE FULLY TIGHTENING)

PLACE THE CAMERA

BALL INSIDE THE

RECESS FLANGE

ATTACH THE MAIN BRACKET

TO THE RECESS FLANGE

WITH THREE 1/2"

SCREWS

INSTALL THE ASSEMBLY

INTO A 3-1/4" DRYWALL

HOLE THEN TIGHTEN

THE THREE FLANGE WING

SCREWS

FLANGE

WING

SCREWS

IF FLANGE WINGS GET

STUCK, USE A FLAT BLADE

SCREWDRIVER IN THE

ACCESS SLOTS

TO FREE THEM

3-1/4" HOLE

IN DRYWALL

RECESS FLANGE

MAIN BRACKET

SNAP THE TRIM

RING ONTO THE

RECESS FLANGE

AFTER CAMERA

ALIGNMENT

TRIM

RING

DON'T TIGHTEN THE

SCREWS UNTIL AFTER

CAMERA ALIGNMENT

VIDEO OUT

FROM

CAMERA

BLACK CONNECTOR

POWER INPUT

FEMALE MINI-JACK

MALE RCA

TO FEMALE

TYPE-F ADAPTER

RG-59 OR RG-6 COAX TO VIDEO

MONITOR OR CHANNELPLUS

MODULATOR

USE THE SECOND RCA-TO-F

ADAPTER AT THE OTHER

END OF THE COAX IF REQUIRED

YELLOW CONNECTOR

VIDEO OUTPUT

FEMALE RCA

MALE

F-CONNECTOR

CAMERA

CONNECT THE CAMERA'S

VIDEO OUTPUT TO A MONITOR

OR TO A CHANNELPLUS

MODULATOR

NOTE: FOR THE BEST PICTURE, RG-59U OR RG-6U COAX

IS RECOMMENDED. RG-6U IS MILITARY GRADE COAX

THAT HAS A BRAIDED SHIELD AND 20 AWG SOLID

COPPER CENTER CONDUCTOR

MAXIMUM RECOMMENDED

VIDEO CABLE LENGTH:

RG-59 750-1000 FEET

RG-6 1000-1500 FEET

VIDEO OUT

FROM CAMERA

BLACK CONNECTOR

POWER INPUT

FEMALE MINI-JACK

12 VDC 500 mA

POWER SUPPLY

TRANSFORMER

CAMERA

CONNECT THE CAMERA'S POWER INPUT

TO THE POWER SUPPLY TRANSFORMER

TRANSFORMER

MALE MINI-JACK

IN MOST INSTALLATIONS, THE POWER WIRE BETWEEN

THE TRANSFORMER AND THE CAMERA WILL NEED TO

BE EXTENDED

USE 18 AWG STRANDED UN-SHIELDED 2-CONDUCTOR

WIRE TO ADD TO THE TRANSFORMER'S WIRE LENGTH

(DO NOT CUT THE POWER WIRE ON THE CAMERA)

OBSERVE POLARITY WHEN SPLICING THE WIRE! THE

WHITE STRIPE ON THE TRANSFORMER'S WIRE IS

POSITIVE (+)

YELLOW CONNECTOR

VIDEO OUTPUT

FEMALE RCA

PLUG THE

TRANSFORMER

INTO A 120 VAC

OUTLET

MAXIMUM RECOMMENDED

POWER WIRE LENGTH:

1500 FEET

ADJUST THE CAMERA

TO VIEW THE DESIRED AREA

TIGHTEN THE LOCKING

SCREWS ON THE CAMERA

CASE AFTER ADJUSTING

THE CAMERA

ADJUST THE MONITOR

FOR THE BEST PICTURE

SURFACE MOUNT

RECESS MOUNT

LOCKING SCREWS (3)

SURFACE MOUNT

RECESS MOUNT

Channel Plus 7441 Install Manual

Channel Plus 7441 Install Manual

Channel Plus 7441 Install Manual

Related papers

Other documents