ETC Irideon AR500 Disassembly Instructions

Brand: ETC

Model: Irideon AR500

Type: Disassembly Instructions

ETC Irideon AR500 is a professional lighting fixture that offers a wide range of features for precise lighting control. With its advanced optics and color mixing system, the AR500 delivers vibrant and accurate colors for a variety of applications. The unit's rugged construction and user-friendly design make it ideal for use in demanding environments.

IRID 110 AR500 Disassembly Instructions Revised: 7/27/2000 Page 1 of 2

IRID 110

IRID 110IRID 110

IRID 110

AR500 DISASSEMBLY INSTRUCTIONS

AR500 DISASSEMBLY INSTRUCTIONSAR500 DISASSEMBLY INSTRUCTIONS

AR500 DISASSEMBLY INSTRUCTIONS

Important Note

Important NoteImportant Note

Important Note

Units are static sensitive. Observe care when installing/servicing. Retain original packaging for

returns/service.

Stanchion

StanchionStanchion

Stanchion

Note: Make sure gaskets make a good seal whenever changing out parts.

Note: Make sure gaskets make a good seal whenever changing out parts.Note: Make sure gaskets make a good seal whenever changing out parts.

Note: Make sure gaskets make a good seal whenever changing out parts.

Ballast Plate

Ballast PlateBallast Plate

Ballast Plate

• Different Ballasts for different voltages

Composer Control Protocol Plate

Composer Control Protocol PlateComposer Control Protocol Plate

Composer Control Protocol Plate

• CPU

• Address Wheels √ ≈00∆ is self-test

• LED»s √ Green is data, yellow is power

• Comm protection PCB

• Power supply

• Fuse for Power to CPU

• Resistor

DMX512 Control Plate

DMX512 Control PlateDMX512 Control Plate

DMX512 Control Plate

• Address Board √ Self-tests in the 900 range

• Power Supply √ 2 fuses

• CPU √ 2 fuses

• Power to board

• Data

• Igniter (remote stanchion)

• Remove cover from remote foot (loosen screws in diagonal pattern)

• Disconnect AC from T-block

• Remove screws from Igniter mounting plate and pull out igniter

IRID 110 AR500 Disassembly Instructions Revised: 7/27/2000 Page 2 of 2

Head

HeadHead

Head

Front and Back covers

Front and Back coversFront and Back covers

Front and Back covers

• Loosen 6 screws and remove head enclosure front cover

• Loosen 6 screws and remove head enclosure rear cover

• Loosen 3 clips to replace reflector

Lenses

LensesLenses

Lenses

• Loosen 6 captive screws

• Remove lens clamping ring and lens

• Remove gasket and place on new lens

Lamp and Socket

Lamp and SocketLamp and Socket

Lamp and Socket

• Remove 4 screws

• Pull socket out and replace lamp

Motors and Actuator Arms

Motors and Actuator ArmsMotors and Actuator Arms

Motors and Actuator Arms

• Using fingers or a short screwdriver, spread tabs of drive shaft and remove from brass swivel link

• Disconnect drive cable

• Locate and remove 3 screws attaching Linear Actuator Motor Assembly to head enclosure. Note

position of cable clamp.

• Slide the motor assembly out (be careful of shafts)

Color Filter Assembly

Color Filter AssemblyColor Filter Assembly

Color Filter Assembly

• Disconnect motors

• Remove 3 screws holding the Color Mechanism to the head enclosure

• Carefully slide the mechanism out of the head enclosure

Problems

ProblemsProblems

Problems

• Not many, solid unit

• Connector in hub can be mismade causing burnout

ETC Irideon AR500 Disassembly Instructions

ETC Irideon AR500 Disassembly Instructions

ETC Irideon AR500 Disassembly Instructions

Related papers

Other documents