Art.nr. BR601-331, utgåva 1 - 2005-03-20
8
2:1 Folding and unfolding
2:2 Brakes - Rear wheels
3:1
Locking - Front wheels
3:2
Tilt
3:3 Driving bow
4:1 Mounting the seating system
4:2
Care instructions
4:3 Marking
4:4 Spare parts
4:5 Warranty
4:6
Suitable seating systems
4:7
Technical data
Zitzi Wave
BR601-40, edition 1 - 2010-05-06
4:1 Mounting the seating system
The seating system can easily be attached to the
mountingplate.
-
Press down the ”locker” and turn it to the right,
intothegap,seeg.1.
- Push Zitzi from the front into the mountingplate.
Pushuntilitisblockedupintheback.Seeg2
- Press down the ”locker” and turn it back to its
originalposition,straightforward.Seeg.3
NOTE!
Turn until a ”clicking sound” is heard.
Zitzi is now safely mounted in the frame.
Table of contents
MANUAL
It is very important that everyone in care of
the child reads this manual.
If you need additional information you
are more than welcome to contact
Anatomic SITT AB.
Adjustment / adaptation of
Zitzi Wave must be done by
a medical / suitable person.
Weight:
Tilt:
Seat width:
Length & width:
Seat height:
Max load:
Wheels:
14 kg
+20
0
/-30
0
40 cm
96 x 65 cm
43 cm
65 kg
175 x 250 mm
Tillverkare / Manufacturer
Anatomic SITT AB
Box 6137, SE-60006 Norrköping
SWEDEN - Phone +46 (0)11-16 18 00
Check the checkbox if the product
is CUSTOMIZED. The CE Mark is no
longer valid and should be removed.
Check
here!
4:2 Care instructions
Wipe it off with a damp rag or if the farme is very dirty clean the frame with some kind
carschampoo. Be careful with the electric parts and the gasspring. Make sure that all moveable
parts
arecompleteandxed.Changeifnecessary.
Cleanitfromdirtwitharag.Makesurethatthedrivingwheelisputbackonproperlyafter
cleaning it.
Controll
allmovablepartsfortorndamages.Exchangeifneeded.Ifyoufeelinsecureabout
anything, you are more than welcome to contact us by calling +46 11 16 18 00 or send us an
email at [email protected].
A consumed part or product should be separated by material and then thrown into a junkyard.
4:3
Marking
TheframeareCE-markedandmarkedwhithoneidenticationnumberthataretobe
used under all correspondence regarding this product.
4:4
Spare parts
Only spare parts delivered from Anatomic SITT AB may be used.
4:5
Warranty
1 year, manufacturing defect.
4:6
Suitable seating systems
ZitziDel,ZitziDelPro&AnatomicSITS.Forothercombinations,contactAnatomicSITTAB.
4:7 Technical data
Sticker placement!
2:2 Brakes - Rear wheels
The frame has a central brake pedal that locks
both wheels.
To lock the wheels - Press the front of the pedal
To unlock to wheels - Press the back of the pedal
2:1 Folding and unfolding
The chassis is easy to fold and unfold.
Unfolding - Grab hold of the padded handle and lift so that the undercarriage rises and make
sure that the locking sleeves snaps into place.
F
olding-Standbehindthechassisandpullthelock-handleforfoldingupwards.
Push forward and downwards.
Make
sure that the locking sleeves lock properly!
Be careful to avoid risk of pinching in the moving parts.
You shall ALWAYS lock the wheels
when you leave your Zitzi Wave on an
uneven surface.
!
3
3:2 Tilt the seat
Quick-release Lock-handle
- Release the lock-handle on the left side
- Pull the quick release on the right side and adjust the angle of the seat.
- Note that the quick-release ”clicks” and locks the seat plate.
- Tighten the lock handle
3:1 Direction lock
Locking the direction of travel:
- Twist the knob 90 degrees.
- Push the undercarriage forward so that the
wheels straighten up and the lock snaps in
position.
-
Checktheknobsothatitistightagainstthe
pipe and that the locking shaft has entered the hole.
Unlocking the direction of travel:
- Pull the knob up and twist it 90 degrees.
- Release the knob so that the ground cut-outs
hook up on the pipe.
-
Checkthatthedirectionlockisproperlyunlocked.
3:3 Angle adjustment, driving bow
Knob (A)
- Loosen the knob (A)
- Adjust to desired angle
- Tighthen the knob
Accessories, X-long driving bow
Will replace standard driving bow.
!
Make sure the seat is locked!
-
1
-
2
