agno's MrotatorA Instruction and Maintenance Manual

Brand
agno's
Model
MrotatorA
Type
Instruction and Maintenance Manual
w
ww
www.agnos.com
AGNO’S EQUIPMENT
Instruction and Maintenance Manual
MrotatorA Panoramic Head
w
ww
www.agnos.com
AGNO’S EQUIPMENT
MrotatorA Panoramic Head
Instruction and Maintenance Manual
w
ww
www.agnos.com
AGNO’S EQUIPMENT
Instruction and Maintenance Manual
MrotatorA Panoramic Head
Package contents
1 - MrotatorA body
2 - Protecting gasket
3 - 3/8”-1/4” pitch adapter
4 - Allen wrench
Thank you for choosing our products.If you follow these instruc-
tions, you will be able to use your Mrotator to take wonderful
spherical panoramic photos.
It is not necessary to lubricate the mechanisms, as the factory
lubrication is enough.
If when removing the Mrotator from its package, you notice ha-
los caused by excessive lubrication, they can be removed using
a clean cotton cloth. For the levelling and relevant instructions,
please refer to the document “CORRECT PROCEDURE FOR
LEVELING”, which can be downloaded from our web site.
The polyurethane foam used for the packaging is the same as
the one used to manufacture bath sponges. You may use it for
this purpose instead of throwing it away, in order to make a little
contribution to the prevention of pollution.
w
ww
www.agnos.com
AGNO’S EQUIPMENT
Instruction and Maintenance Manual
MrotatorA Panoramic Head
Product description
1 Rotating body
2 Lens supporting bracket
3 Lens securing screw
4 Lens position reference notch
5 Toroidal level
6 Goniometric scale
7 Goniometric scale reference
w
ww
www.agnos.com
AGNO’S EQUIPMENT
Instruction and Maintenance Manual
MrotatorA Panoramic Head
If necessary, screw the 3/8” to 1/4”
pitch adapter onto the bottom of the MrotatorA
(fi g.1). Position the rubber protection
supplied with the kit between the tripod
and the head (fi g.2)
Fig. 1
Fig. 2
w
ww
www.agnos.com
AGNO’S EQUIPMENT
Instruction and Maintenance Manual
MrotatorA Panoramic Head
Specifi cations
Fit the FC-E8 into its housing, making sure that the back of it is kept in contact with the notch on
the bracket. This allows the converter and its nodal point to be accurately positioned at the centre
of rotation of the MrotatorA.
Fasten the securing screw on the bracket side using the Allen wrench, being careful not to fasten
too tightly in order not to damage the lens.
The threaded ring nuts found on digital cameras are assembled in factory without taking into ac-
count their thread setting. For this reason, it is necessary to orientate the assembly in rotation,
according to the camera we want to use.
Proceed as follows:
1 – Assemble the converter on the housing bracket as described above
2 – Screw the camera on the converter to the bottom.
3 – Loosen the lens securing screw on the housing bracket and rotate the Camera/Converter
assembly until it is parallel to the ground.
4 – Tighten the securing screw on the housing bracket.
For ease of use, the camera can be unscrewed from the converter without disassembling it from
the MrotatorA; in this way the assembly will always be ready and set-up.
w
ww
www.agnos.com
AGNO’S EQUIPMENT
Instruction and Maintenance Manual
MrotatorA Panoramic Head
Technical Features
Head height 150 mm
Loadable weight 0,850 kg.
Head weight 280 gr.
Size 50x50x150
Divisions / Releases 180°-2, 120°-3
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6

agno's MrotatorA Instruction and Maintenance Manual

Brand
agno's
Model
MrotatorA
Type
Instruction and Maintenance Manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents