Comprehensive EXT-DIGAUD-141 User manual
- Category
- Supplementary music equipment
- Type
- User manual
EXT-DIGAUD-141
User Manual
Digital Audio Extender
Release A5
*Preferred
ii
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this unit near water.
6. Clean only with a dry cloth.
7. Do not block any ventilation openings. Install in accordance with the manufacturer’s
instructions.
8. Do not install or place this unit near any heat sources such as radiators,
heat registers, stoves, or other apparatus (including ampliers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized
plug has two blades with one wider than the other. A grounding type plug has two
blades and a third grounding prong. The wide blade or the third prong are provided for
your safety. If the provided plug does not t into your outlet, consult an electrician for
replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs,
convenience receptacles, and the point where they exit from the unit.
11. Only use attachments/accessories specied by the manufacturer.
12. To reduce the risk of electric shock and/or damage to this unit, never handle or touch
this unit or power cord if your hands are wet or damp. Do not expose this
unit to rain or moisture.
13. Unplug this unit during lightning storms or when unused for long periods of time.
14. Refer all servicing to qualied service personnel. Servicing is required when
the unit has been damaged in any way, such as power-supply cord or plug is
damaged, liquid has been spilled or objects have fallen into the unit,
the unit has been exposed to rain or moisture, does not operate normally,
or has been dropped.
15. Batteries that may be included with this unit and/or accessories should never be
exposed to open ame or excessive heat. Always dispose of used batteries
according to the instructions.
Important Safety Instructions
Gefen warrants the equipment it manufactures to be free from defects in material and
workmanship.
If equipment fails because of such defects and Gefen is notied within two (2) years from
the date of shipment, Gefen will, at its option, repair or replace the equipment, provided
that the equipment has not been subjected to mechanical, electrical, or other abuse or
modications. Equipment that fails under conditions other than those covered will be
repaired at the current price of parts and labor in effect at the time of repair. Such repairs
are warranted for ninety (90) days from the day of reshipment to the Buyer.
This warranty is in lieu of all other warranties expressed or implied, including without
limitation, any implied warranty or merchantability or tness for any particular purpose, all of
which are expressly disclaimed.
1. Proof of sale may be required in order to claim warranty.
2. Customers outside the US are responsible for shipping charges to and from Gefen.
3. Copper cables are limited to a 30 day warranty and cables must be in their original
condition.
The information in this manual has been carefully checked and is believed to be accurate.
However, Gefen assumes no responsibility for any inaccuracies that may be contained
in this manual. In no event will Gefen be liable for direct, indirect, special, incidental, or
consequential damages resulting from any defect or omission in this manual, even if
advised of the possibility of such damages. The technical information contained herein
regarding the features and specications is subject to change without notice.
For the latest warranty coverage information, refer to the Warranty and Return Policy under
the Support section of the Gefen Web site at www.gefen.com.
iii
Warranty Information
iv
Technical Support
(818) 772-9100 (800) 545-6900
8:00 AM to 5:00 PM Monday - Friday, Pacic Time
Fax
(818) 772-9120
Email
Web
http://www.gefen.com
Mailing Address
Gefen, LLC
c/o Customer Service
20600 Nordhoff St.
Chatsworth, CA 91311
Product Registration
Register your product here: http://www.gefen.com/kvm/Registry/Registration.jsp
iv
Contacting Gefen Technical Support
v
• Use CAT-5e (or better) cables to connect the Sender and Receiver units. The length
of the cable should not exceed 330 feet (100 meters) in length.
• The Digital Audio Extender will accept audio on either the SPDIF or OPT port, on the
Sender unit, and output the audio on both the OPT and SPDIF ports of the Receiver
unit. However, when both digital and optical cables are used to connect the source
to the Sender unit, the SPDIF port has priority. To hear the audio signal on the OPT
port, on the Receiver unit, disconnect the digital coax cable from the SPDIF port on
the Sender unit.
Digital Audio Extender is a trademark of Gefen, LLC.
© 2015 Gefen, LLC. All Rights Reserved. All trademarks are the property of their respective owners.
Gefen, LLC reserves the right to make changes in the hardware, packaging, and any accompanying documentation
without prior written notice.
v
Operating Notes
This product uses UL or CE listed power supplies.
Pb
vi
Features and Packing List
Features
• Extends any S/PDIF and TOSLINK® digital audio device up to 330 feet (100 meters)
from the source
• Supports multichannel digital audio like Dolby® Digital and DTS™
• Supplies clear digital audio over long distances as if connected locally
• Streamlines audio installations by allowing source devices to be located in off-site or
unseen rack
• One CAT-5e cable used for extension
• Audio is transmitted digitally for zero signal loss
Packing List
The Digital Audio Extender ships with the items listed below. If any of these items are not
present in the box when you rst open it, immediately contact your dealer or Gefen.
• 1 x Digital Audio Extender (Sender unit)
• 1 x Digital Audio Extender (Receiver unit)
• 1 x 6 ft. optical cable
• 1 x 5V DC power supply
• 1 x Quick-Start Guide
viii
Table of Contents
1 Getting Started
Introduction............................................................................................................ 2
Sender unit .................................................................................................... 2
Receiver unit ................................................................................................. 4
Installation ............................................................................................................. 6
Connection Instructions ................................................................................. 6
Sample Wiring Diagram ................................................................................ 7
2 Appendix
Specications ...................................................................................................... 10
1 Getting Started
Digital Audio Extender
Introduction............................................................................................................ 2
Sender unit .................................................................................................... 2
Receiver unit ................................................................................................. 4
Installation ............................................................................................................. 6
Connection Instructions ................................................................................. 6
Sample Wiring Diagram ................................................................................ 7
page | 2
Page Title
Sender unit
SPDIF
CAT-55V DC
OPT
Digital Audio
Extender S
Introduction
Getting Started
Getting Started
1 2 3 4
page | 3
Page TitleIntroduction
ID Name Description
1 SPDIF Connect an RCA-type cable from the
digital output of the source to this port.
If a digital audio source is connected to
both the SPDIF and OPT ports, then this
port has priority and will supply the audio
to the Receiver unit.
2 OPT Connect the included optical audio cable
from this TOSLINK™ port to the digital
output of the source.
If a digital audio source is connected to
both the SPDIF and OPT ports, then the
SPDIF port has priority and will supply the
audio to the Receiver unit.
3 5V DC Connect the included 5V DC power supply
to this power receptacle.
4 CAT-5 Connect a CAT-5e cable (or better) from
this port to the CAT-5 port on the Receiver
unit.
Getting Started
page | 4
Receiver unit
SPDIF
CAT-5
OPT
Digital Audio
Extender R
Introduction
Getting Started
Getting Started
1 2 3 4
page | 5
Introduction
ID Name Description
1 SPDIF Connect an RCA-type cable from the
digital output of the source to this port.
This port will output digital audio from
either the OPT or SPDIF port on the
Sender unit.
If a digital audio source is connected to
both the SPDIF and OPT ports, on the
Sender unit, then the SPDIF audio signal
will be heard on the output.
2 OPT Connect an optical audio cable from this
TOSLINK™ port to an audio amplier.
This port will output digital audio from
either the OPT or SPDIF port on the
Sender unit.
If a digital audio source is connected to
both the SPDIF and OPT ports, on the
Sender unit, then the SPDIF audio signal
will be heard on the output.
3 CAT-5 Connect a CAT-5e cable (or better) from
this port to the CAT-5 port on the Receiver
unit.
4 Power LED This LED indicator will glow solid red
when the Receiver unit is powered.
The Receiver unit is powered only
when the Sender unit is powered and
connected to the Receiver unit using a
CAT-5e (or better) cable.
Getting Started
page | 6
Installation
Getting Started
Getting Started
Connection Instructions
► Audio
1. Connect an RCA- type cable from the digital output of the audio source to the SPDIF
port on the Sender unit.
2. Connect the included optical cable from the optical audio output of the audio source to
the OPT port on the Sender unit.
3. Connect an RCA-type cable from the SPDIF port on the Receiver unit to the AV
receiver.
4. Connect an optical cable from the OPT port on the Receiver unit to the AV receiver.
The Digital Audio Extender will accept audio on either the SPDIF or OPT port, on the
Sender unit, and output the audio on both the OPT and SPDIF ports of the Receiver
unit.
► CAT-5
5. Connect a CAT-5e (or better) cable from the CAT-5 port on the Sender unit to the
CAT-5 port on the Receiver unit.
► Power
6. Connect the included power supply to the 5V DC power receptacle on the Sender unit
and connect the power cord to an available electrical outlet.
Power to the Receiver unit is supplied by the Sender unit, over the CAT-5e cable.
Information
When both digital and optical cables are used to connect the source to the
Sender unit, the SPDIF port has priority. To hear the audio signal on the OPT
port, on the Receiver unit, disconnect the digital coax cable from the SPDIF
port on the Sender unit.
page | 7
Getting Started
Sample Wiring Diagram
Installation
Digital Audio Extender
Sender
Digital Audio Extender
Receiver
Audio Receiver
Speakers with
TOSLINK Input
Speakers with
Coax Input
(Up To 330 Ft)
DIGITAL AUDIO (COAX) CABLE
CAT-5 CABLE
DIGITAL AUDIO (TOSLINK) CABLE
EXT-DIGAUD-141
CAT-5e (or better) CABLE
Connectors, Controls, and Indicators
Audio Input • 1 x S/PDIF
• 1 x TOSLINK®
Audio Output • 1 x S/PDIF
• 1 x TOSLINK®
CAT-5 • 1 x RJ-45, shielded
Power Indicator • 1 x LED, red
Operational
Power Supply • 5V DC
Power Consumption • 5W maximum
Physical
Dimensions (W x H x D) • 3.8” x 1.2” x 1.4” (96mm x 30mm x 35mm)
Shipping Weight • 5 lbs (2.3 kg)
page | 10
Appendix
Specications
Page is loading ...
Page is loading ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
Comprehensive EXT-DIGAUD-141 User manual
- Category
- Supplementary music equipment
- Type
- User manual
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
Gefen EXT-AUD-1000 User manual
-
Gefen EXT-PS5-8R User manual
-
-
Gefen EXT-COMPAUD-141 User manual
-
-
Gefen EXT-DVI-AUDIO-CAT5 User manual
-
Gefen EXT-DIGAUD-141 User manual
-
-
-
Gefen EXT-UHDA-HBT2 User manual