Convergent Design Odyssey 7Q User manual

Updated October 28, 2014 | Firmware Release v3.10.100

PROFESSIONAL MONITOR/RECORDER

USER MANUAL

Updated October 28, 2014 | Firmware Release v3.10.100

USER MANUAL // FIRMWARE V3.10.100

TABLE OF CONTENTS

INTRODUCTION // READ THIS FIRST! 2

PACKAGE CONTENTS 3

OVERVIEW 4

Odyssey7Q Features 4

Odyssey7Q Specicaons 5

RECORDING CAPABILITIES 6

Included Free with Odyssey7Q 6

Recording OPTIONS (available for purchase) 7

RECORDING OPTION RENTALS 9

Rental Acvaon Keys 9

Parameters for Rentals 9

RECORD TIME CAPACITIES 10

Apple ProRes 422 (HQ) & Uncompressed DPX 10

Record Opons (Purchase & Rental) 11

SSD MEDIA 12

2.5” Premium SSD Media 12

Odyssey Ulity Drive 12

ANATOMY 13

Mechanical Drawings 15

GETTING STARTED 16

Odyssey7Q Acvaon 16

Inializing 16

Powering Down 17

Seng Up & Using the Odyssey7Q 17

The Odyssey7Q Menu 17

Demo Mode 17

MENU SYSTEM 18

Odyssey Menu 18

SETUP Menu 19

Outputs Menu 21

Upper Tool Bar (Record Mode) 22

Lower Tool Bar (Record Mode) 25

Upper Tool Bar (Play Mode) 29

Lower Tool Bar (Play Mode) 30

WORKING WITH MEDIA 35

Recording to SSD Media 35

Loss of Power During a Record 35

Downloading Media 35

File Storage 36

CD Data Unpacker 37

CD Clip Merger 37

CD Apple ProRes Transfer Ulity 37

POST PRODUCTION 39

Working with Files Recorded 39

Uncompressed Support (DPX sequence) 39

Apple ProRes 422 (HQ) 40

FS700 RAW Support (DNG Sequences) 40

FS700 RAW: Dealing with RAW Files 40

FS700 FCP X Import Sengs 41

Canon C500 4K RAW Support 42

ARRI Alexa ARRIRAW Support 42

ACCESSORIES 43

Convergent Design Accessories 43

Third Party Accessories 47

RELEASE NOTES 48

Firmware v3.10.29 48

Firmware v2.20.141 51

Firmware v2.10.141 53

Earlier Versions 57

LIMITED WARRANTY 58

APPENDIX 59

Monitor-->Record Opons 59

WEBSITE LINKS 60

Convergent Design, Inc.

4525 Northpark Drive

Colorado Springs, CO 80918

Tel: ++(720)221-3861

Email: CDSupport@convergent-design.com

Website: Convergent-Design.com

1

INTRODUCTION // READ THIS FIRST!

BEFORE YOU BEGIN USING THE ODYSSEY7Q, WE STRONGLY

SUGGEST YOU REVIEW THE INCLUDED QUICK START GUIDE. WE

ALSO STRONGLY RECOMMEND THE FOLLOWING:

1. Always record to the INTERNAL MEDIA OF THE CAMERA; this is critical for proper

timecode and ideal for dual media / backup.

2. DO NOT REMOVE THE FOUR SCREWS FROM REAR OF CASE. This may result in

damage to the OLED panel. Such damage is not covered by warranty.

3. Power and Cabling: Make sure you have PROPER POWER (6.5-34VDC), plugged in to

the proper power port (left side of recorder), and that 3G-rated SDI cables are used.

4. Power source must be able to provide up to 24 watts at all times to the Odyssey7Q.

5. When powering the Odyssey7Q from an ARRI ALEXA camera, we recommend using

the 24V R/S Fischer-3 output from the ALEXA using the optional Convergent Design

cable.

6. Familiarize yourself with the equipment and test prior to shooting.

7. Before using the SSDs it is IMPERATIVE TO FORMAT them in the Odyssey7Q.

Formatting SSD media is a DESTRUCTIVE PROCESS; any existing data will be lost

during format.

8. Ensure that the camera’s viewnder data is not being recorded; IF YOU SEE

VIEWFINDER DATA ON THE ODYSSEY7Q monitor, then it will be recorded! In a future

update, if your camera can provide both clean and data-overlayed video feeds, it will be

possible to monitor one while recording the other.

9. NEVER DELETE ANY FILES OFF AN SSD FROM A COMPUTER, except when going

through a rmware update procedure.

10. While we recommend that you always maintain the latest rmware on your Odyssey7Q,

WE DO NOT RECOMMEND UPDATING FIRMWARE IF YOU ARE IN THE MIDDLE OF

A SHOOT (unless specically instructed to do so by our Technical Support staff).

11. When ofoading media, ALWAYS MAKE A BACKUP COPY, ideally to a RAID1 drive.

12. Be sure to allow the Odyssey7Q to nish closing a Record le before taking any further

action.

13. Always safely eject SSD Media by pressing the button before removing SSD media

from the Odyssey7Q.

2

Odyssey7Q box contains one (1) Odyssey7Q monitor/recorder and one (1) universal power

supply.

PACKAGE CONTENTS

MEDIA AND ACCESSORIES SOLD SEPARATELY!

3

CONTINUED »

ODYSSEY7Q FEATURES

MONITORING

PROFESSIONAL MONITOR: 7.7” 1280x800 OLED panel featuring true blacks, and accurate

color with a full range color gamut for REC709 or DCI-P3 viewing.

IMAGE ANALYSIS TOOLS: Waveform, Vectorscope (in future update), Histogram, False

Color exposure view, Zebra, three-mode Focus Assist, Pixel Zoom (1:1 & 2:1), LUTs, and

Frame Guides.

MULTI-STREAM MONITORING: up to four HD video signals can be input and viewed

simultaneously (quad-split) or live-switched (choose between inputs for full screen display). A

future paid update will allow Multi-Stream Recording of up to four simultaneous Apple ProRes

422 (HQ) les and an XML log le of the live switch.

FLEXIBLE I/O: two dedicated 3G-SDI inputs, two dedicated 3G-SDI outputs, two switchable

3G-SDI input/outputs, one HDMI input, one HDMI output. Active Cross-Conversion means that

all outputs are always active regardless of which input is used.

RECORDING

HIGH-CAPACITY RECORDING: Two high-speed solid state Drives (SSD), available in 256

GB or 512 GB, allow for extended recording.

4K / UHD / 2K / HD VIDEO RECORDING: Record 4K (4096x2160), UHD (3840x2160), 2K

(2048x1080) and HD (1920x1080, 1280x720) Video in Apple ProRes 422 (HQ).

UNCOMPRESSED 4:4:4 RGB VIDEO RECORDING: Record 2K (2048x1080) and HD

(1920x1080) Video in 12-bit or 10-bit uncompressed DPX les.

RAW RECORD OPTIONS: Optional recording features available at any time for purchase or

time-based rental. Options include:

• ARRIRAW (ALEXA)

• CANON RAW (C500)

• SONY RAW (FS7/FS700)

• POV RAW (Indiecam and IO Industries cameras)

OVERVIEW

4

CONTINUED »

ODYSSEY7Q SPECIFICATIONS

Display

7.7" OLED, 1280x800, RGB 8-bit panel, ~ 16 million colors, wide gamut, 3400:1 contrast, 176°

viewing, true blacks

SDI Video I/O

HD-SDI/3G support: Single/Dual link, 2-inputs, 2-outputs, 2 Bi-Direconal (can be inputs or

outputs), Full-size BNCs

HDMI Video I/O

HDMI I/O Version 1.4a support, up to 1080p30 422 8-bit

LUT Support

ARRI, CANON, SONY S-Log, S-Log 2, S-Log 3 or (FUTURE) custom user-loadable LUTs

Focus Assist

Video + Edges (Peaking), Edges Only, Enhanced Edges, user choice of color: Red, Green, or Blue

Zebras

Currently one adjustable level, future two levels, one allows for a user specied range, the other

is acve on a specied IRE level and above

False Color

False Color with 5 programmable levels

Waveform

Luma only, RGB Parade, Red only, Blue only, Green only

Histogram

Luma only, RGB Parade, Red only, Blue only, Green only

Vectorscope

(FUTURE) Color Vectorscope with 2X zoom

1:1 and 2:1 Pixel

Zoom

Image Zoom, Automac Vercal Flip (defeatable) , Aspect Rao Guides

Mul-Stream

Display

Display four independent 1080 HD streams simultaneously (Quad-split) with live-switch

capability

Digital Audio I/O

8-channel embedded audio (48KHz, 24-bit) (2 channel inially, 8-channel via future rmware

update)

Analog Audio I/O

3.5mm stereo headphone output, (FUTURE) 3.5mm stereo unbalanced input up to -10db

Remote** and

Timecode

Timecode: LTC I/O (BNC) or embedded SDI / HDMI, (FUTURE) RS-232 I/O programmable GPIO.

User Interface

Capacive Touchscreen, two mechanical keys

DC Power Input

6.5 to 34vdc with built-in reverse polarity protecon; locking power connector, built-in power

switch

Power Draw

8 was (monitor only), 9-15 was (simultaneous monitor/record mode)

Weight and Size

560 grams / 1.3 lbs., 7.9"" x 6.1"" x 1.0"" (200 x 155 x 25 mm), -10 to +40°c

(Operang), -20 to +70°c (storage)

Onion Skinning

(FUTURE) Overlay pre-recorded sll frame on live video with opacity slider

View Monitor Out

Record Clean Video

(FUTURE) Display the monitor-out (viewnder data) on the OLED while recording a clean video

signal. Available when using the SONY F3, SONY FS700, CANON C500 and ARRI Alexa cameras.

Record Triggers

Touchscreen, SDI record trigger (ARRI, CANON, PANASONIC, RED, SONY), Timecode, Oponal

remote control cable

Recording SSD

Media

Convergent Design SSDs with power-loss protecon, in 256GB and 512GB sizes,

420Mb/sec write, 500Mb/sec read speed, compable with USB 3.0 and Thunderbolt Adapters.

SSDs and adapters sold separately.

Recording Formats

(base Odyssey7Q)

Compressed formats:

4K/UHD 10-bit YCC 422 up to 30p

2K 10-bit YCC 4:2:2 up to 60fps

1080p 10-bit YCC 422 up to 60 fps

(FUTURE): 1080p RGB 12-bit 444 up to 60fps

Uncompressed formats:

2K/1080p 10/12-bit 444 up to 30p

1080p RGB 10bit 444 up to 60fps

OVERVIEW

5

CONTINUED »

The Odyssey7Q can record a variety of video signals and, with optional recording keys, several

RAW data video formats. With another optional recording key the Odyssey7Q will also be able

to record up to four HD video signals simultaneously.

All recording options are available for demo on the Odyssey7Q, but will appear with a blue or

pink line “watermark” across the recorded image.

Recording options are available to purchase or rent on a time-active (daily) basis from the

Convergent Design website at:

Convergent-Design.com/products/recording-options.html

INCLUDED FREE WITH ODYSSEY7Q

VIDEO

4K/UHD (4096x2160, 3840x2160): Apple ProRes 422 (HQ), 4:2:2 YCC 10-bit, frame rates:

23.98p, 24p, 25p, 29.97p

2K/HD (2048x1080, 1920x1080): Uncompressed video in DPX stacks, 12-bit/10-bit 4:4:4,

frame rates: 23.98p, 24p, 25p, 29.97p, 30p

2K/HD (2048x1080, 1920x1080): Uncompressed video in DPX stacks, 10-bit 4:2:2 (recorded as

4:4:4), frame rates: 23.98p, 24p, 25p, 29.97p, 30p, 50p, 59.94p, 60p

2K/HD (2048x1080, 1920x1080): Apple ProRes 422 (HQ), 4:2:2 YCC 10-bit, frame rates:

23.98p, 24p, 25p, 29.97p, 50p, 59.94p, 60p, 50i, 60i

HD (1280x720): Apple ProRes 422 (HQ), 4:2:2 YCC 10-bit, frame rates: 50p, 60p

4K video over 4x SDI feeds

2K/HD video over SDI up to 60p

HD (1080) over HDMI up to 30p or 60i; HD (720) over HDMI up to 60p

MULTI-STREAM HD

Video Monitoring

3G-SDI accepted 1080p/psf frame rates: 23.98, 24, 25, 29.97, 30, 50i, 60i

Up to four HD video signals viewable simultaneously.

OLED display divided into quadrants or a single input may be selected for full screen display.

Live-switch between inputs directly.

Inputs are SDI A, SDI B, SDI A I/O, SDI B I/O (signals auto-detected; [SDI A] must always be

present).

HD video signals do not need to be Genlocked.

HD video signals do not need to match frame rates.

HDMI input available in future free rmware update.

NOTE: this is a monitoring mode only. A future opon will allow recording of up to four HD

video signals.

NOTE: If feeding video from a switcher to Odyssey7Q, the switcher must have internal frame

synchronizers or the cameras input to the switcher must be genlocked.

RECORDING CAPABILITIES

6

CONTINUED »

RECORDING CAPABILITIES (CONT’D)

RECORDING OPTIONS (AVAILABLE FOR PURCHASE)

Additional recording options are available for purchase and/or rental through our website.

ARRI ALEXA ARRIRAW

(Available for purchase

and/or daily rental)

The Odyssey7Q supports all ARRIRAW formats and frame rates output by Alexa Classic

cameras.

ARRIRAW data is recorded as .ari les.

ARRIRAW 16:9 frame rates: 23.98, 24, 25, 29.97, 30, 48*, 50*, 59.97*, 60*

ARRIRAW 4:3 frame rates: 23.98, 24, 25, 29.97, 30, 48*

*Future Firmware Update for 4:3 Support

*NOTE: ARRIRAW above 30fps requires two SSDs to simultaneously record. In a future

rmware update only one SSD will be required for all frame rates.

More Info: hps://convergent-design.com/products/odyssey7q/arri-alexa

CANON C500 Cinema

RAW

(Available for purchase

and/or daily rental)

The Odyssey7Q supports CANON C500 4K RAW. Future rmware updates will support “Slow

& Fast” mode, and other C500 formats.

CANON Cinema RAW data is recorded as .RMF les.

4K & QHD (4096x2160 & 3840x2160)

Supported 4K RAW frame rates: 23.98, 24, 25, 29.97, 50*, 59.94*, 4K Half RAW 50, 59.94,

100*, 120*

2K/1080p 12-bit/10-bit 4:4:4 support 23.98, 24, 25, 29.97

*NOTE: CANON RAW 50-60p and Half RAW 100-120p requires two SSDs to simultaneously

record.

More Info: hps://convergent-design.com/products/odyssey7q/canon-c500

SONY FS7/FS700 RAW

(Available for purchase)

The Odyssey7Q supports SONY FS7/FS700 4K & 2K RAW and high quality video derived from

RAW.

FS 4K RAW frame rates: 23.98, 25, 29.97, 50, 59.94, (FS700 only) 4K 440 frame burst mode:

100, 120

FS RAW 2K frame rates: 23.98, 25, 29.97, 50, 59.94, 100, 120, 200*, 240*

NOTE: FS 4K/2K RAW data is recorded as .DNG les.

FS 4K RAW to UHD Apple ProRes 422 (HQ) / 10-bit / 23.98, 24, 29.97

FS 4K RAW to HD Apple ProRes 422 (HQ) / 10-bit / 23.98, 24, 29.97

*NOTE: 2K RAW 200fps and 240fps, 4K RAW 50/60 and 100/120 Burst Recording require that

you record to two SSDs simultaneously.

More Info: hps://convergent-design.com/products/odyssey7q/sony-fs700

7

NEXT: RECORDING OPTION RENTALS »

RECORDING CAPABILITIES (CONT’D)

POV RAW

(Available for purchase

and/or daily rental)

Supports several industrial/special use cameras’ RAW outputs:

IO Industries Flare 2KSDI: 2K/HD 10-Bit RAW 23.98-60p

Indiecam indieGS2K: 2K/HD 10-Bit RAW 60-120p

Indiecam indieGS2K: HD 10-Bit RAW 23.98-60p

Indiecam indieGS2K: HD 12-Bit RAW 23.98-60p

NOTE: RAW data is recorded as .DNG les.

NOTE: Video outputs do not require Record Opon.

More Info: hps://convergent-design.com/products/odyssey7q/pov-RAW

MULTI-STREAM

(Available for purchase

and/or daily rental

in a future rmware

release)

Supports recording up to four HD streams simultaneously via 3G-SDI.

Addional specicaons will be made available upon release.

NOTE: Mul-Stream Monitoring is acve with UNIT acvaon and does not require the

purchase of this record opon

8

NEXT: RECORD TIME CAPACITIES »

RECORDING OPTION RENTALS

RENTAL ACTIVATION KEYS

Rental Activation Keys may be purchased though our website for the Canon C500 Cinema

RAW, the ARRI Alexa ARRIRAW and POV RAW recording options. Please visit the links in the

Recording Capabilities section for more information.

PARAMETERS FOR RENTALS

Rentals are based on a 24 hr period, Rentals can be added to the unit in daily (24 hour)

increments up to a maximum of 30 days at a time.

A rental starts the rst time a record is performed in the rental codec, then the 24 hour clock

starts.

Note that during a 24 hr rental period you will not be allowed to adjust the clock after the rst

record. Thus users must set a central time, or choose a timezone that will best t all of their

given locations in that 24 hr period.

After 24 hours a user may adjust the clock as needed, till the next record is performed.

Rentals are unit specic, by the unit serial number, and must be purchased via our website.

Once a rental key is input into a unit, there is no way of retrieving or transferring the rental to

another unit.

To activate a rental simply enter the 8 character key into the unit’s activation section.

To check the status of an active rental touch the codec box.

When a rental period has two days remaining, the rental text will change to yellow.

When a rental period has one day remaining, the time will display in the form of minutes and

will be ash for the last hour.

When there is one minute remaining, if a record is started, that entire clip will be recorded

without a watermark regardless of length up to a maximum of 80 mins. (In other words, will let

you nish your last take, which can be a maximum of lling up both drives, based on a RAW

format.

After the nal clip the time remaining will change back to a white 0 mins.

For more information or to purchase Rental Options please visit our the Recording Options

page of our website at Convergent-Design.com/products/recording-options.

For support with Rental Options visit us online at Convergent-Design.com/support

9

CONTINUED »

APPLE PRORES 422 (HQ) & UNCOMPRESSED DPX

The Odyssey7Q can record numerous video and data formats. Record time

capacities vary based on format. The chart below indicates maximum record

time in minutes based on the use of two 512 GB SSDs (1TB). For 512 GB (one

512 GB SSD or two 256 GB SSDs), divide in half. For 256 GB, divide by four.

MAXIMUM RECORD TIME IN MINUTES - TWO 512GB SSDS (1TB)

Recording Format 24fps 25fps 30fps 50fps 60fps

4K/UHD Apple ProRes 422 (HQ) 194 186 155

2K Apple ProRes 422 (HQ) 600 572 475 284 237

1080p Apple ProRes 422 (HQ) 660 636 528 316 264

1080i Apple ProRes 422 (HQ) 636 528

720p Apple ProRes 422 (HQ) 316 264

2K Uncompressed DPX (RGB 444 12-bit) 70 66 60

2K Uncompressed DPX (RGB 444 10-bit) 84 80 62

1080p Uncompressed DPX (RGB 444 12-bit) 70 66 60

1080p Uncompressed DPX (RGB 444 10-bit) 84 80 62 38 33

1080p Compressed 444 (12-bit@24fps, 10-bit@60fps)** 500 480 400

**Not currently supported. Available through a future rmware upgrade.

(PLEASE SEE THE NEXT PAGE TO VIEW RECORD TIME CAPACITIES FOR RECORDING

OPTIONS)

RECORD TIME CAPACITIES

10

RECORD TIME CAPACITIES (RECORD OPTIONS)

RECORD OPTIONS (Purchase & Rental)

Recording options can be purchased and/or rented through our website. The following are the

approximate recording times while recording with these options. The charts below indicate

maximum record time in minutes based on the use of two 512 GB SSDs (1TB). For 512 GB

(one 512 GB SSD or two 256 GB SSDs), divide in half. For 256 GB, divide by four.

ARRIRAW OPTION (Available for Purchase or Daily Rental)

Recording Format 24fps 25fps 30fps 50fps 60fps

ARRIRAW 16:9 100 97 80 46 40

ARRIRAW 4:3**

(top framerate = 48fps, 38min rec. me)

76 73 60

CANON C500 4K RAW OPTION (Available for Purchase or Daily Rental)

Recording Format 24fps 25fps 30fps 50fps 60fps 100fps 120fps

Canon 4K/QHD RAW

(100/120fps = 4K half RAW)

62 60 50 30 25 30 25

SONY FS7/FS700 RAW OPTION (Available for Purchase Only)

Recording Format 24fps 25fps 30fps 50fps 60fps 100fps 120fps 200fps 240fps

Sony 4K RAW 50 50 40 24 20

Sony 2K RAW 202 196 164 96 80 48 40 24 20

4K RAW to HD Apple

ProRes 422 (HQ)

"4K2HD"

660 636 528 316 264

4K RAW to HD

compressed 444**

"4K2HD"

500 480 400

4K RAW to 4K Apple

ProRes 422 (HQ)

“4K24K”

194 186 155

4K RAW burst

(440 frames)

155 takes in 1TB of

Storage

4.4 sec

/ 17.6

@25p

3.7 sec

/ 18.3

@24

POV RAW OPTION (Available for Purchase or Daily Rental)

Recording Format 24fps 25fps 30fps 50fps 60fps 100fps

2K 10-bit RAW 252 242 202 120 100

HD 10-bit RAW 268 256 214 128 106 62 52

HD 12-bit RAW 222 214 178 106 88

MULTI-STREAM HD OPTION (Not Currently Available**)

Recording Format 24fps 25fps 30fps 50fps 60fps

2-Stream Apple ProRes 422 (HQ)** 330 318 264

4-Stream Apple ProRes 422 (HQ)** 165 159 132

** Available through a future rmware upgrade.

11

2.5” PREMIUM SSD MEDIA

To enable recording on the Odyssey7Q, you must use Convergent Design Premium SSD

media. Only Convergent Design Premium SSDs will work in the Odyssey7Q. These SSDs,

available in 256GB and 512GB and must be purchased separately. Firmware updates must

be completed only with Convergent Design Premium SSD or Convergent Design SSD Utility

Drives.

256GB SSD for Odyssey7 and 7Q CD-SSD-256GB

512GB SSD for Odyssey7 and 7Q CD-SSD-512GB

ODYSSEY UTILITY DRIVE

The Odyssey Utility Drive is designed as a lower cost alternative to the Odyssey Premium SSD

media for secondary tasks. The Odyssey Utility Drive can be used for Odyssey7Q rmware

updates and future functionality such as 3D-LUT les.

The Convergent Design SSD Utility Drive will not record video les. It is intended for Odyssey7Q

owners who do not wish to tie up an SSD with utility features, or for Odyssey7Q owners who

use their devices as monitors and do not need to purchase the more expensive recording

media.

Utility Drive for Odyssey7 and 7Q CD-SSD-UTILITY

SSD MEDIA

12

CONTINUED »

ODYSSEY7Q - BOTTOM

There are eleven connector ports on the bottom side of the Odyssey7Q (left to right)

PWR ON

Power input socket to Odyssey7Q (see Geng Started – Power). Just in front of the PWR ON port is

a buon, which is a Force Power On/O control. Hold buon ve seconds to force power o. This is

only to be used if standard power on or o procedures fail (see Geng Started – Inializing).

SDI A IN

BNC connector for 3G-SDI input A

SDI B IN

BNC connector for 3G-SDI input B

LTC IO

BNC connector for Linear Timecode input/output

SDI A IO

BNC connector for 3G-SDI input/output A. In Mul-Stream monitoring mode, the Odyssey7Q can

accept up to four HD video inputs. These IO ports allow addional inputs or addional outputs for

the Odyssey7Q.

HDMI IN

HDMI 1.4 input from HDMI video source.

SDI B IO

BNC connector for 3G-SDI input/output B. In Mul-Stream monitoring mode, the Odyssey7Q can

accept up to four HD video inputs. These IO ports allow addional inputs or addional outputs for

the Odyssey7Q.

SDI A OUT

BNC connector for 3G-SDI output A

SDI B OUT

BNC connector for 3G-SDI output B

AUDIO IN

3.5mm mini-phone stereo socket for analog audio in. This input will be enabled in a free future

rmware update.

AUDIO OUT

3.5mm mini-phone stereo headphone socket.

ODYSSEY7Q - TOP

There are two Solid State Drive (SSD) slots, SSD1 and SSD2.

Only Convergent Design 256 GB and 512 GB SSDs can be used to capture video on the

Odyssey7Q. The Odyssey Utility Drive can be used for rmware updates and other future

functions, but not to record video les. To mount SSD, insert connector-end rst with the label

facing forward and the handle near ush with the back of the Odyssey7Q. Push gently but

rmly until the handle ange is ush with the top of the Odyssey7Q. It is a snug t, but the SSD

should insert smoothly.

ANATOMY

13

ODYSSEY7Q - LEFT SIDE

There are two Function buttons, F1 LOCK and F2 SHUT DOWN.

F1 LOCK

Lockout control for the Odyssey7Q touchscreen. Push to engage and SCREEN LOCK will appear in the

center of the touchscreen’s Upper Tool Bar. Push F1 again to disengage. Engaging F1 also re-calibrates

the touchscreen.

F2 SHUT

DOWN

Preferred method to power down the Odyssey7Q. Properly closes les on the SSDs and performs other

maintenance funcons (see Geng Started -- Powering Down). Push to acvate prompt asking SAFELY

POWER DOWN UNIT? In a future free rmware update it will be possible to program these buons for

addional funcons.

ODYSSEY7Q - RIGHT SIDE

There are three connector ports, (top to bottom) USB, HDMI OUT and RMT.

USB

An access point for servicing by Convergent Design.

HDMI OUT

Output to an HDMI compable device

RMT

A remote control connecon to the Odyssey7Q.

In a future free rmware update the RMT port will allow control interface with funcons of

the Odyssey7Q.

KENSINGTON LOCK PORT

A rectangular hole above the RMT port is for accepng a Kensington Security Lock.

MOUNTING

The Odyssey7Q features three ¼-20 threaded sockets, one on the lower rear of the case and

one each on the left and right sides of the case. Do not exceed 11mm of depth when inserting a

bolt, otherwise damage may occur to the Odyssey7Q. Additionally, there are four M3 threaded

sockets on the rear of the case and two M4 sockets on each of the sides of the case.

ANATOMY

CONTINUED »

14

ANATOMY

MECHANICAL DRAWINGS

15

CONTINUED »

ODYSSEY7Q ACTIVATION

Convergent Design requires each Odyssey7Q to be registered via our website. This is so

that we can provide notices of free rmware updates, issue alerts for critical issues, and track

rentals or purchases of record options.

Upon rst initializing of the Odyssey7Q (see below), a prompt will appear asking if the device is

to be Activated at this time or if it is to be used in DEMO mode. In DEMO mode the Odyssey7Q

is fully functional, however a blue or pink bar “watermark” will appear in any recorded video.

In order to Activate the Odyssey7Q after initial purchase, go to Convergent-Design.com to

register and activate your unit. When you have registered a new account (or logged into your

existing account) you will be able to Add a Device to your account at which time you will be

provided the Basic Activation Key for your device.

The Activation prompt will appear upon every initialization of the Odyssey7Q until the device is

Activated. When Activate is selected, follow the prompts to Activate the Odyssey7Q using the

Basic Activation Key you were given on the website.

Also, make sure your Odyssey7Q has the latest rmware, posted here:

Convergent-Design.com/support/rmware-downloads.html

See Firmware Updates under the Appendix below for more information on how to put new

rmware on your Odyssey7Q.

INITIALIZING

Plug in power to the Odyssey7Q. It should take about 5-10 seconds to initialize, depending on

the mode it is set to. If the Odyssey7Q does not self-initialize, push the PWR ON button next

to the power socket on the lower left corner of the Odyssey7Q.

As part of the initializing process, SMPTE color bars may appear briey on the screen. If there

is a signal input into SDI A IN that matches the record format the Odyssey7Q is set to, then

the image should appear on the screen. If there are SSDs mounted in the Odyssey7Q then

a DETECTING SSD message will appear on the lower left of the screen. If the SSD needs

to be re-initialized or formatted, a second message may appear. If the Trigger Button in the

Upper Tool Bar appears as a red box surrounding a white circle, then the Odyssey7Q is ready

to record.

GETTING STARTED

16

NEXT: MENU SYSTEM »

GETTING STARTED

POWERING DOWN

While it may seem an odd time to note this, it is important to know that there is a preferred

method to shutting down the Odyssey7Q. On the left side of the case, the F2 SHUT DOWN

button should be pressed. This prompts a conrmation to “SAFELY POWER DOWN UNIT?”

Powering down in this fashion properly closes the les and directory system on the SSDs,

preventing corruption. If the Odyssey7Q should ever suffer a failure and the F2 SHUT DOWN

sequence does not function properly, the unit can be Force Power Off by holding the PWR

ON button by the power socket on the lower left corner of the Odyssey7Q, or simply by pulling

the power connector out of the power socket. If the Odyssey7Q is ever powered down in this

fashion, it is important to run a recovery on the SSDs in the Odyssey7Q menu at MENU »

ODYSSEY » SSDs » RECOVER SSD1 » RECOVER SSD2.

SETTING UP & USING THE ODYSSEY7Q

The touch screen of the Odyssey7Q features all of the device’s controls in a straightforward,

easy to navigate structure. Each box is a “virtual button.” Tap it briey to activate/deactivate

it, or hold it for a few seconds to open up the menu dening its function. The controls at the

top of the display (Upper Tool Bar) are the recording, playback and formatting administration.

The controls at the bottom of the display (Lower Tool Bar) are the image analysis adjustments.

THE ODYSSEY7Q MENU

Starting on the left, tapping the

☼

button brings up the initial setup menus for the Odyssey7Q.

Don’t be intimidated by the number of selections in the

☼

section. This is by far the most in-

depth section of the Odyssey7Q touchscreen menus. More information about the Odyssey7Q

Menu System is available on the following pages.

DEMO MODE

Out of the box the Odyssey7Q is in DEMO MODE and must be owner-registered with

Convergent Design. On the Odyssey7Q a watermarking blue bar will appear on the lower

third of the image both on the OLED and in the recording while in DEMO MODE. The Record

Options are also available in their own DEMO MODE even once the unit is activated, so that

they may be tested but will show a blue bar in the frame. Activation of each Record Option

eliminates the blue bar.

To activate the Odyssey7Q after initial purchase, go to Convergent-Design.com, create a user

account and add the device to your account. When you add a device to your account you will

be provided with the Basic Activation Key for that device. Once this is completed, any time you

wish to purchase or rent a Record Option, return to the Convergent Design website and follow

the prompts to the online store. Upon payment the website will present a code which can then

be entered into the Odyssey7Q by tapping the appropriate button under the Activation menu.

To see if a selection has been enabled, tap on the option’s button to see if ACTIVE appears.

17

CONTINUED »

MENU SYSTEM

ODYSSEY MENU

The ODYSSEY Menu allows you to access basic device settings. This is where you can

view and enter activation keys, set date, time & metadata, format & recover SSDs and view

information about the device such as the rmware version and serial number. It is accessed by

tapping

☼

then tapping ODYSSEY.

ODYSSEY

→

Option Description Notes

SET

ACTIVATION

UNIT

Enter Key or

‘OK’

For acvang Odyssey7Q

(required)

Tap to reveal a key code

prompt.

To acvate the Odyssey7Q

aer inial purchase, go

to Convergent-Design.

com, create an account

and add the device. Once

this is completed, anyme

one wishes to purchase or

rent a recording opon,

return to the Convergent

Design website and follow

the prompts. The website

will present a code which

can then be entered into

the Odyssey7Q on the

[acvaon] menu page.

To see if a selecon has

already been enabled, tap

on that opon’s buon to

see if ACTIVE appears.

FS700 RAW

Enter record

opon

key using

on-screen

keyboard

Shows

ACTIVE if a

key has been

entered for

the record

opon.

RAW output of Sony FS7 or FS700

CANON RAW

RAW output of Canon C500

ARRIRAW

RAW output of ARRI ALEXA

POV RAW

RAW output of various industrial

and specialty use cameras such as

IO Industries or IndieCam

MULTI-STREAM

(Available in a future rmware

update) Record up to four HD

signals simultaneously (Mul-

stream monitoring is acve with

UNIT acvaon.)

DEMO MODE: ALL AVAILABLE RECORD OPTIONS ARE FUNCTIONAL IN A DEMO MODE, BUT IF THE

OPTION HAS NOT BEEN ACTIVATED THE IMAGE FOR THAT OPTION WILL APPEAR WITH A LARGE BLUE BAR

“WATERMARK” ON SCREEN WHEN RECORDING. THIS BAR IS RECORDED IN THE IMAGE FILE.

TIME

Set the appropriate me. IMPORTANT FOR

RECORDING OPTION

RENTALS

DATE

Set the appropriate date.

RESET

MENU

Restore all default sengs.

Does not eect rmware

version or record opons.

METADATA

Resets metadata elds

ALL (FACTORY DEFAULTS)

Resets all sengs

SSDS FORMAT SSD1

Permanently erases everything

on SSD1.

FORMATTING IS A

DESTRUCTIVE PROCESS

AND WILL ERASE ANY FILES

CURRENTLY ON THE SSD.

BE SURE TO DOWNLOAD

ALL FILES BEFORE

FORMATTING.

FORMAT SSD2

Permanently erases everything

on SSD2.

FORMAT BOTH

Permanently erases everything

on both cards.

RECOVER SSD1

Non-destrucvely recovers /

rebuilds le system of SSD1

Use only in extreme cases

(such as if a computer

corrupts the SSDs le

system).

RECOVER SSD2

Non-destrucvely recovers /

rebuilds le system of SSD2

PLEASE NOTE: Formang should be performed at the start of use of any new SSDs and the start of

any new project. Recovery is for when the SSD was not properly dismounted from the Odyssey7Q.

This includes physically removing the SSD without running the eject sequence, sudden loss of power

to the Odyssey7Q or improper powering down of the Odyssey7Q. The Recover process accesses any

incomplete les on the SSD and, when possible, properly closes them. NOTE: FORMATTING OF SSDs

SHOULD ALWAYS BE PERFORMED ON THE ODYSSEY7Q.

ABOUT

Displays the rmware version, serial number, warranty status, and which Opons are acvated.

Check our website regularly to ensure you are running the current rmware.

18

CONTINUED »

MENU SYSTEM

SETUP MENU

The SETUP Menu functions as both a detailed status display as well as a selection point

to change status and settings. It allows you to setup the Odyssey7Q and adjust settings for

monitoring and recording including the type of camera input, recording format, video cadence,

frame rate, audio source, timecode source and record trigger. Many of the controls are also

available by pressing other Upper Toolbar buttons. The SETUP menu is accessed by tapping

☼

then tapping SETUP.

☼

╚

ODYSSEY

SETUP

OUTPUTS

SET UP MONITORING / RECORDING

CAMERA: SONY FS7/FS700

MONITOR->RECORD 4K RAW>UHD PRORES

∟

( ACTIVATED )

VIDEO CADENCE: PROGRESSIVE/PSF

TIMECODE SOURCE: SDI/HDMI

AUDIO CHANNELS: 2

AUDIO SOURCE: SDI/HDMI

RECORD TRIGGER: RECORD BUTTON

PROJECT RATE: FOLLOWS INPUT

SETUP MENU OPTIONS

CAMERA:

Tapping status boxes brings up a list of selections for each. Choice of CAMERA determines

MONITOR -> RECORD selections for that camera. CAMERA also determines Trigger,

Timecode and LUT integration.

AVAILABLE CAMERAS:

Sony FS7/FS700

Sony (F3, F5 and F55 and others)

Canon (C500 and others)

ARRI (ARRI Alexa)

POV RAW (IndieCam and IO Industries)

Other (sundry HD video sources)

Panasonic

RED

Mul-Stream (up to 4 HD video sources, monitoring only)

MONITOR->RECORD

Displays options for the currently selected camera

(See the MONITOR-->RECORD OPTIONS chart in APPENDIX (p59) (for full list of

options in this menu selection)

19

Page is loading ...

Convergent Design Odyssey 7Q User manual

This manual is also suitable for

Convergent Design Odyssey 7Q User manual

Related papers

Other documents