Page is loading ...
Page is loading ...
• Further, protect the product from direct solar radiation, strong heat (>45 °C), cold
(<0 °C), dust and dirt, splashes and dripping water, vibrations or mechanical loads.
• Never use the product immediately after it has been brought from a cold room
into a warm one. The condensation generated could destroy the product. Allow
the device to reach room temperature before connecting and using it. This may
take several hours.
• In commercial institutions, the accident prevention regulations of the Employer’s
Liability Insurance Association for Electrical Systems and Operating Materials are
to be observed.
• In schools, educational centres, hobby and self-help workshops, the operation of
the product has to be supervised by trained employees.
• When setting up the product, make sure that the cable is not pinched, kinked or
damaged by sharp edges.
• Any maintenance or repair work may only be carried out by authorised personnel.
• Check the product for damage before each use! If you detect any damage, DO
NOT connect or use the product! This may present a danger to life!
• Consult an expert when in doubt about operation, safety or connection of the
device.
• Maintenance, modications and repairs are to be performed exclusively by an
expert or at a qualied shop.
• If you have questions which remain unanswered by these operating instructions,
contact our technical support service or other technical personnel.
LEDs on the extender
Duplex Lights up when the RJ45 connection is working in the full-duplex mode.
Speed Lights up at a speed of 100 MBit on the RJ45 port.
Link/Act Lights up on active connection to the RJ45 port, blinks during data transfer.
Power Lights up when the device is supplied with power.
CO Lights up on the extender that is in the master mode (CO).
Link/Nego
Flashes slowly while the connection is being established; lights up if the
connection is active; ashes quickly during data transfer.
Connection and getting started
• Before connecting the product, stick the enclosed rubber feet on the underside of both
devices.
• You then have to congure the two extenders, by means of the DIP switches.
Set the DIP switch 1 on one device to “CO” (Master) and on the other one to “CPE” (Slave).
The DIP switch 2 setting must be the same for both devices. “Fast” is used for a high data
rate (e. g. video streaming). “Interleave” is used to ensure that fewer data packets are lost.
Thus, should there be any problems while using the setting “Fast”, change to the setting
“interleave”.
Use the same setting for the DIP switch 3 on both extenders. If the data transfer is approx.
the same in both directions, select “S.ISDN” for synchronous data transfer. However, if only
one point is sending, as is the case for instance during video streaming, set the switch to
“998.ISDN”.
The standard setting for the DIP switch 4 is “6dB”. Should you face any problems here, select
“9dB”. Here again, the settings for both devices must be the same.
• After conguring both extenders, connect the extender that is set to “CO” to the rst network
device, e. g. your router, using a 1:1 wired network cable. Connect the 2nd extender (“CPE”)
to the other device, e.g. a network camera, also using a 1:1 wired network cable.
• Now connect both devices, using a conventional telephone cable with RJ11 plugs. Only the
two middle connectors of the cable have to be assigned.
• Finally, connect the wall plug transformers to the two extenders and then connect each of
them to a mains socket.
• After a few seconds, the devices will be operational and establish a network connection
automatically.
The maximum cable length between the two extenders is approx. 1000 m. Please
note that, depending on the cable length, the transfer rate may be reduced to
10 MBit.
The maximum speed is ca. 100/60 MBit for asynchronous data transfer or
ca. 90 MBit for synchronous data transfer. This speed is reached with a cable length
of up to ca. 300 m.
Operating instructions
Ethernet 2-Wire Extension
Item no. 1604208
Intended use
The product is intended to be used for extending the maximum cable length of an Ethernet
connection with 10/100 MBit. The transmission using VDSL technology takes place via a
2-pole telephone cable with RJ11 plugs. A cable length of 1000 m is possible between the two
extenders. It is also possible to use telephone lines that already exist as well as to transmit the
signal via a telephone jack.
It is intended for indoor use only. Do not use it outdoors. Contact with moisture, e.g. in
bathrooms, must be avoided under all circumstances.
The power is supplied from the wall plug transformers included in the delivery.
For safety and approval purposes, you must not rebuild and/or modify this product. If you use
the product for purposes other than those described above, the product may be damaged.
In addition, improper use can cause hazards such as short circuiting, re, electric shock etc.
Read the instructions carefully and keep them. Make this product available to third parties only
together with its operating instructions.
This product complies with the statutory national and European requirements. All company
names and product names are trademarks of their respective owners. All rights reserved.
Delivery content
• 2 long reach ethernet extenders
• 2 wall plug transformers
• 8 rubber feet
• Operating instructions
Latest operating instructions
Download the latest operating instructions via the link www.conrad.com/downloads or scan the
QR code shown. Follow the instructions on the website.
Explanation of symbols
The lightning symbol inside a triangle is used when there is a potential risk of
personal injury, such as electric shock.
An exclamation mark in a triangle indicates important instructions in this operating
manual that absolutely have to be observed.
The arrow symbol indicates specic tips and advice on operation.
Safety instructions
Read the operating instructions carefully and especially observe the safety
information. If you do not follow the safety instructions and information
on proper handling in this manual, we assume no liability for any resulting
personal injury or damage to property. Such cases will invalidate the warranty/
guarantee.
• The device is not a toy. Keep it out of the reach of children and pets.
• Do not leave packaging material lying around carelessly. This may become
dangerous playing material for children.
• Protect the product from extreme temperatures, direct sunlight, strong jolts, high
humidity, moisture, ammable gases, vapours and solvents.
• Do not place the product under any mechanical stress.
• If it is no longer possible to operate the product safely, take it out of operation and
protect it from any accidental use. Safe operation can no longer be guaranteed
if the product:
- is visibly damaged,
- is no longer working properly,
- has been stored for extended periods in poor ambient conditions or
- has been subjected to any serious transport-related stresses.
• Please handle the product carefully. Jolts, impacts or a fall even from a low height
can damage the product.
• Also observe the safety and operating instructions of any other devices which are
connected to the product.
• The product is only intended for use in dry, indoor locations. No part of the product
should be allowed to become moist or wet, never take hold of it if your hands are
wet! There is a risk of a life-threatening electric shock!
• The design of the wall plug transformers complies with protection class II. Only
connect the wall plug transformer to a standard mains socket connected to the
public supply.
• Only use the external wall plug transformer enclosed to power the unit.
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microlming, or the
capture in electronic data processing systems require the prior written approval by the editor. Reprinting, also in
part, is prohibited. This publication represent the technical status at the time of printing.
Copyright 2017 by Conrad Electronic SE. *1604208_V1_1017_02_mxs_m_en
Care and cleaning
• The product does not require any maintenance, never take it apart.
• Disconnect the product from the power supply before cleaning. Unplug the wall plug
transformer from the mains socket (all network connections will cease to function). Also,
remove the RJ45 and the RJ11 cable.
• Do not use any aggressive cleaning agents, rubbing alcohol or other chemical solutions as
they can cause damage to the housing and malfunctioning.
• Clean the product with a dry, ber-free cloth.
• Do not immerse the product in water.
Disposal
Electronic devices are recyclable waste and must not be disposed of in the
household waste. At the end of its service life, dispose of the product according to
the relevant statutory regulations.
You thus full your statutory obligations and contribute to the protection of the
environment.
Technical data (for each extender)
a) Extender
Input voltage ................................................. 5 V/DC
Ports for data transfer .................................... 1 Port RJ45 (10/100 MBit), 1 Port RJ11 (VDSL)
Operating temperature ..................................0 to +45 °C
Storage temperature ......................................-20 to +90 °C
Humidity during operation ..............................10 - 90 % RH (non-condensing)
Dimensions (W x H x D) ................................approx. 75 x 23 x 102 mm
Weight ...........................................................approx. 203 g
b) Wall plug transformer
Input voltage .................................................. 100 - 240 V/AC, 50-60 Hz
Output voltage/current ...................................5 V/DC, 2 A
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
in other languages
- français: Renkforce RF-4812624 Le manuel du propriétaire
- Deutsch: Renkforce RF-4812624 Bedienungsanleitung
- Nederlands: Renkforce RF-4812624 de handleiding
Related papers
-
Renkforce RF-4451433 Owner's manual
-
Renkforce 1342100 Owner's manual
-
-
-
-
-
-
-
-
Other documents
-
VOLTCRAFT SPAS-2100 Operating instructions
-
VOLTCRAFT SNG 12/1500-OW-N Operating instructions
-
TRU Components POWER CONTROL 2760 Operating instructions
-
-
Routers 2520104 User manual
-
-
Apexis APM-JP6235-WS Operating instructions
-
Conrad N150 Operating Instructions Manual
-
-
