Dakota Digital VHX-62T-FJ Mounting Manual

Dakota Digital
Brand
Dakota Digital
Model
VHX-62T-FJ
Type
Mounting Manual

Dakota Digital VHX-62T-FJ is a digital instrument cluster designed specifically for 1962-’84 Toyota Land Cruisers. It's a direct-fit replacement for the stock gauge cluster and provides a wide range of features and capabilities.

The VHX-62T-FJ includes a high-resolution LCD display that shows all the essential gauges, including speedometer, tachometer, fuel level, oil pressure, and water temperature. It also includes a number of programmable features, such as shift lights, warning lights, and data logging.

One of the most useful features of the VHX-62T-FJ is its ability to interface with a variety of sensors, including GPS, tire pressure sensors, and wideband oxygen sensors. This allows you to add even more gauges and functionality to your Land Cruiser, giving you a complete picture of its performance.

Dakota Digital VHX-62T-FJ is a digital instrument cluster designed specifically for 1962-’84 Toyota Land Cruisers. It's a direct-fit replacement for the stock gauge cluster and provides a wide range of features and capabilities.

The VHX-62T-FJ includes a high-resolution LCD display that shows all the essential gauges, including speedometer, tachometer, fuel level, oil pressure, and water temperature. It also includes a number of programmable features, such as shift lights, warning lights, and data logging.

One of the most useful features of the VHX-62T-FJ is its ability to interface with a variety of sensors, including GPS, tire pressure sensors, and wideband oxygen sensors. This allows you to add even more gauges and functionality to your Land Cruiser, giving you a complete picture of its performance.

Manual # 650473B
VHX-62T-FJ
Dakota Digital VHX Instrument Installation
For 1962-’84 Toyota Land Cruiser
Your new VHX-62T-FJ kit includes:
Installation
Installation
Manuals
Control Box
36” CAT5 Cable
Universal Sender
Pack
VHX Display
1. First, remove the stock gauge cluster; it is held in place by two large screws (arrows). Retain the
factory screws for reassembly. Also, disconnect the wiring harness and speedometer cable to
completely remove the gauge cluster.
Tang Speed Adapter
Pulse Generator
Manual # 650473B
4. Place the VHX system over the back of the bezel and crimp the seven (7) tabs back over
the clear lens. Then, attach the provided 36” CAT5 cable to the back of the VHX system.
Carefully route the other end to the control box mounting location.
2. The stock bezel will be reused; un-crimp the seven (7) tabs that clamp over the stock gauge housing.
The rubber seal should remain inside the stock bezel.
3. If the stock ammeter is still connected in
your rig, tie these wires together. You
can use a short 10-32 screw, or ideally
solder the connection. Be sure to
insulate the connection as these wires
are carrying a large amount of energy.
Manual # 650473B
5. Tip the bottom of the VHX system in the dash to ensure the bottom tabs lay behind the dash and
secure the VHX system to the dash using the two (2) stock mounting screws. You are now done
mounting the VHX display; refer to the main manual for wiring instructions to complete the VHX
installation.
6. The stock oil filter adapter may need to be removed to tap the 1/8 NPT deeper to accommodate the
Dakota Digital sender.
Manual # 650473B
WARNING: This product can expose you to chemicals including lead, which is known to the State of
California to cause cancer and birth defects or other reproductive harm. For more information go to
www.P65Warnings.ca.gov
7. The supplied speed sensor can connect directly to the stock transfer case using the included cable
and brass tang. Before installation, pull out the inner cable and ensure the brass stop is inserted in
the 7/8” end, and then slide the brass tang onto the same end of the cable. See photos below.
Cable and tang, as delivered
Sensor threaded on to cable assembly,
ready for installation
7/8” thread-end of cable assembled with
brass tang
Cable inserted, brass tang in place
delivered
Inner cable flipped 180
degrees
Inner cable removed
8. Refer to the main installation and supplemental manuals to complete the VHX installation.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Dakota Digital VHX-62T-FJ Mounting Manual

Dakota Digital
Brand
Dakota Digital
Model
VHX-62T-FJ
Type
Mounting Manual

Dakota Digital VHX-62T-FJ is a digital instrument cluster designed specifically for 1962-’84 Toyota Land Cruisers. It's a direct-fit replacement for the stock gauge cluster and provides a wide range of features and capabilities.

The VHX-62T-FJ includes a high-resolution LCD display that shows all the essential gauges, including speedometer, tachometer, fuel level, oil pressure, and water temperature. It also includes a number of programmable features, such as shift lights, warning lights, and data logging.

One of the most useful features of the VHX-62T-FJ is its ability to interface with a variety of sensors, including GPS, tire pressure sensors, and wideband oxygen sensors. This allows you to add even more gauges and functionality to your Land Cruiser, giving you a complete picture of its performance.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers